POWER MIRROR CONTROL SYSTEM(w/ Memory) Reverse Shift-linked Function of Power Mirrors does not Operate

DESCRIPTION

The ECM sends the reverse signal to the main body ECU (multiplex network body ECU) via CAN communication. When receiving the reverse signal, the main body ECU (multiplex network body ECU) sends the reverse request signal to each outer mirror control ECU assembly. Each outer mirror control ECU assembly then performs control in response to the reverse signal.

WIRING DIAGRAM

B006KROE01

CAUTION / NOTICE / HINT

Note


  • First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem.

    Click here

  • If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

  • As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.

Tech Tips

The reverse shift-linked function will not activate when the mirror select switch is in the neutral position (off).

PROCEDURE


  1. CHECK OUTER REAR VIEW MIRROR ASSEMBLY FUNCTION (MEMORY AND MIRROR RESTORING OPERATION)


    1. Check that the mirror operates.

      Click here

      OK
      Mirror operates normally.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO OTHER FLOWCHART (Power Mirror Surface Position is not Memorized) Click here

    OK

  2. CHECK FOR DTC (SFI SYSTEM)


    1. Check for DTCs.

      2GR-FKS:

      Click here


      Powertrain > Engine > Trouble Codes

      2AR-FE:

      Click here


      Powertrain > Engine > Trouble Codes
      OK
      DTCs output does not occur.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO SFI SYSTEM 2GR-FKS: GO TO SFI SYSTEM Click here
    GO TO SFI SYSTEM 2AR-FE: GO TO SFI SYSTEM Click here

    OK

  3. CHECK SHIFT POSITION INDICATOR FUNCTION


    1. Check that the shift position indicator operates.

      Click here

      OK
      Shift position indicator operates normally.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO METER / GAUGE SYSTEM Click here

    OK

  4. CONFIRM MALFUNCTIONING PARTS


    1. Check the malfunctioning outer rear view mirror assembly.

      Click here

      Result
      Result Proceed to
      Both the left and right outer rear view mirror assemblies do not operate A
      Outer rear view mirror assembly LH does not operate B
      Outer rear view mirror assembly RH does not operate C

    A

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    C

    CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH Click here

    B

  5. CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH


    1. Temporarily replace the outer rear view mirror assembly LH with a new or normally functioning one.

      Click here

    2. Check that the reverse shift-linked function operates.

      Click here

      OK
      Reverse shift-linked function operates normally.
      Result
      Proceed to
      OK
      NG

    OK

    END (OUTER REAR VIEW MIRROR ASSEMBLY LH IS DEFECTIVE)

    NG

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH Click here

  6. CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH


    1. Temporarily replace the outer rear view mirror assembly RH with a new or normally functioning one.

      Click here

    2. Check that the reverse shift-linked function operates.

      Click here

      OK
      Reverse shift-linked function operates normally.
      Result
      Proceed to
      OK
      NG

    OK

    END (OUTER REAR VIEW MIRROR ASSEMBLY RH IS DEFECTIVE)

    NG

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH Click here