POWER MIRROR CONTROL SYSTEM(w/ Memory) Power Mirror Surface Position is not Memorized

DESCRIPTION

When the seat memory switch is operated, the switch input signal is sent via CAN communication from the outer mirror control ECU assembly LH*1 or RH*2 to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) then sends the memorization request or recall request signals to the outer mirror control ECU assembly LH and outer mirror control ECU assembly RH via CAN communication. The outer mirror control ECU assembly LH and outer mirror control ECU assembly RH memorize the mirror position when a memorization request signal is received, and move the mirror to the memorized position when a recall request signal is received.


WIRING DIAGRAM

B006MG8E05
B006MG8E02

CAUTION / NOTICE / HINT

Note


  • First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem.

    Click here

  • If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

  • As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.

PROCEDURE


  1. CHECK OUTER REAR VIEW MIRROR ASSEMBLY FUNCTION


    1. Check that the mirror operates.

      Click here

      OK
      Mirror operates normally.
      Result
      Result Proceed to
      OK A
      NG (Driver side outer rear view mirror assembly does not operate) B
      NG (Front passenger side outer rear view mirror assembly does not operate) C

    B

    GO TO OTHER FLOWCHART (Driver Side Power Mirror cannot be Adjusted with Power Mirror Switch) Click here

    C

    GO TO OTHER FLOWCHART (Front Passenger Side Power Mirror cannot be Adjusted with Power Mirror Switch) Click here

    A

  2. CHECK SEAT MEMORY SWITCH (SEAT POSITION MEMORY FUNCTION)


    1. Perform a seat memory operation properly.

      Click here

    2. When any seat memory switch (M1, M2 or M3 switch) is pressed, check that the driver side seat moves to the memorized position.

      OK
      Driver side seat moves to memorized position.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO FRONT POWER SEAT CONTROL SYSTEM Click here

    OK

  3. READ VALUE USING GTS (MIRROR MEMORY)


    1. Using the GTS, read the Data List.

      Click here


      1. for LH side


        Body Electrical > Mirror L > Data List
        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        Mirror Memory No.1 Mirror position memorized in memory switch M1 OFF or ON

        OFF: Not memorized

        ON: Memorized

        		 -
        Mirror Memory No.2 Mirror position memorized in memory switch M2 OFF or ON

        OFF: Not memorized

        ON: Memorized

        		 -
        Mirror Memory No.3 Mirror position memorized in memory switch M3 OFF or ON

        OFF: Not memorized

        ON: Memorized

        		 -

        Body Electrical > Mirror L > Data List
        Tester Display
        Mirror Memory No.1
        Mirror Memory No.2
        Mirror Memory No.3

      2. for RH side


        Body Electrical > Mirror R > Data List
        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        Mirror Memory No.1 Mirror position memorized in memory switch M1 OFF or ON

        OFF: Not memorized

        ON: Memorized

        		 -
        Mirror Memory No.2 Mirror position memorized in memory switch M2 OFF or ON

        OFF: Not memorized

        ON: Memorized

        		 -
        Mirror Memory No.3 Mirror position memorized in memory switch M3 OFF or ON

        OFF: Not memorized

        ON: Memorized

        		 -

        Body Electrical > Mirror R > Data List
        Tester Display
        Mirror Memory No.1
        Mirror Memory No.2
        Mirror Memory No.3
      OK
      The display is as specified in the normal condition column.
      Result
      Result Proceed to
      LH side mirror position cannot be memorized A
      LH side mirror position memory exists but cannot be recalled B
      RH side mirror position cannot be memorized C
      RH side mirror position memory exists but cannot be recalled D
      Both LH side mirror position and RH side mirror position cannot be memorized E

    B

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH Click here

    C

    CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - OUTER MIRROR CONTROL ECU ASSEMBLY RH) Click here

    D

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH Click here

    E

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    A

  4. CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - OUTER MIRROR CONTROL ECU ASSEMBLY LH)


    • *1: w/o Panoramic View Monitor System

    • *2: w/ Panoramic View Monitor System


    1. Disconnect the I19*1 or I33*2 outer rear view mirror assembly LH connector.

    2. Disconnect the I30 outer mirror control ECU assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      w/o Panoramic View Monitor System
      Tester Connection Condition Specified Condition
      I19-7 (VC) - I30-5 (LVC) Always Below 1 Ω
      I19-8 (HSRL) - I30-13 (HSSR) Always Below 1 Ω
      I19-16 (VSRL) - I30-6 (VSSR) Always Below 1 Ω
      I19-15 (E1) - I30-14 (LE1) Always Below 1 Ω
      I19-7 (VC) or I30-5 (LVC) - Body ground Always 10 kΩ or higher
      I19-8 (HSRL) or I30-13 (HSSR) - Body ground Always 10 kΩ or higher
      I19-16 (VSRL) or I30-6 (VSSR) - Body ground Always 10 kΩ or higher
      I19-15 (E1) or I30-14 (LE1) - Body ground Always 10 kΩ or higher
      w/ Panoramic View Monitor System
      Tester Connection Condition Specified Condition
      I33-14 (VC) - I30-5 (LVC) Always Below 1 Ω
      I33-6 (HSRL) - I30-13 (HSSR) Always Below 1 Ω
      I33-15 (VSRL) - I30-6 (VSSR) Always Below 1 Ω
      I33-16 (E1) - I30-14 (LE1) Always Below 1 Ω
      I33-14 (VC) or I30-5 (LVC) - Body ground Always 10 kΩ or higher
      I33-6 (HSRL) or I30-13 (HSSR) - Body ground Always 10 kΩ or higher
      I33-15 (VSRL) or I30-6 (VSSR) - Body ground Always 10 kΩ or higher
      I33-16 (E1) or I30-14 (LE1) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH


    1. Temporarily replace the outer rear view mirror assembly LH with a new or normally functioning one.

      Click here

    2. Check that the memory and reactivation function operates.

      Click here

      OK
      Memory and reactivation function operates normally.
      Result
      Proceed to
      OK
      NG

    OK

    END (OUTER REAR VIEW MIRROR ASSEMBLY LH IS DEFECTIVE)

    NG

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH Click here

  6. CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - OUTER MIRROR CONTROL ECU ASSEMBLY RH)


    • *1: w/o Panoramic View Monitor System

    • *2: w/ Panoramic View Monitor System


    1. Disconnect the I3*1 or I32*2 outer rear view mirror assembly RH connector.

    2. Disconnect the I15 outer mirror control ECU assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      w/o Panoramic View Monitor System
      Tester Connection Condition Specified Condition
      I3-7 (VC) - I15-5 (RVC) Always Below 1 Ω
      I3-8 (HSSR) - I15-13 (HSSR) Always Below 1 Ω
      I3-16 (VSSR) - I15-6 (VSSR) Always Below 1 Ω
      I3-15 (E1) - I15-14 (RE1) Always Below 1 Ω
      I3-7 (VC) or I15-5 (RVC) - Body ground Always 10 kΩ or higher
      I3-8 (HSSR) or I15-13 (HSSR) - Body ground Always 10 kΩ or higher
      I3-16 (VSSR) or I15-6 (VSSR) - Body ground Always 10 kΩ or higher
      I3-15 (E1) or I15-14 (RE1) - Body ground Always 10 kΩ or higher
      w/ Panoramic View Monitor System
      Tester Connection Condition Specified Condition
      I32-14 (VC) - I15-5 (RVC) Always Below 1 Ω
      I32-6 (HSSR) - I15-13 (HSSR) Always Below 1 Ω
      I32-15 (VSSR) - I15-6 (VSSR) Always Below 1 Ω
      I32-16 (E1) - I15-14 (RE1) Always Below 1 Ω
      I32-14 (VC) or I15-5 (RVC) - Body ground Always 10 kΩ or higher
      I32-6 (HSSR) or I15-13 (HSSR) - Body ground Always 10 kΩ or higher
      I32-15 (VSSR) or I15-6 (VSSR) - Body ground Always 10 kΩ or higher
      I32-16 (E1) or I15-14 (RE1) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH


    1. Temporarily replace the outer rear view mirror assembly RH with a new or normally functioning one.

      Click here

    2. Check that the memory and reactivation function operates.

      Click here

      OK
      Memory and reactivation function operates normally.
      Result
      Proceed to
      OK
      NG

    OK

    END (OUTER REAR VIEW MIRROR ASSEMBLY RH IS DEFECTIVE)

    NG

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH Click here