POWER MIRROR CONTROL SYSTEM(w/ Memory) Power Retractable Mirrors do not Operate with Power Retract Mirror Switch

DESCRIPTION

When the outer mirror switch assembly mirror retract switch is operated, return/retract signals are sent to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) sends return/retract signals to the outer mirror control ECU assembly via CAN communication. The outer mirror control ECU assembly returns and retracts the outer rear view mirror assembly based on the received signals.

WIRING DIAGRAM

B006OH7E01

CAUTION / NOTICE / HINT

Note


  • First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem.

    Click here

  • If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

  • As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.

PROCEDURE


  1. READ VALUE USING GTS (OUTER MIRROR FOLD SW)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Main Body > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Outer Mirror Fold SW Mirror retract switch signal OFF or ON

      OFF: Mirror retract switch not in retract position

      ON: Mirror retract switch in retract position

      		 -

      Body Electrical > Main Body > Data List
      Tester Display
      Outer Mirror Fold SW
      OK
      On the GTS screen, ON or OFF is displayed for each item according to the table above.
      Result
      Proceed to
      OK
      NG

    NG

    INSPECT OUTER MIRROR SWITCH ASSEMBLY (MIRROR RETRACT SWITCH) Click here

    OK

  2. CHECK MALFUNCTIONING PARTS


    1. Check the malfunctioning parts.

      Click here

      Result
      Result Proceed to
      Both mirrors are malfunctioning A
      LH side mirror is malfunctioning B
      RH side mirror is malfunctioning C

    A

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    C

    INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (POWER RETRACT FUNCTION) Click here

    B

  3. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (POWER RETRACT FUNCTION)


    1. Remove the outer rear view mirror assembly LH.

      Click here

    2. Inspect the outer rear view mirror assembly LH.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - OUTER MIRROR CONTROL ECU ASSEMBLY LH)


    1. Disconnect the I19 outer rear view mirror assembly LH connector.

    2. Disconnect the I30 outer mirror control ECU assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I19-3 (MR) - I30-3 (MR+) Always Below 1 Ω
      I19-11 (MF) - I30-11 (MR-) Always Below 1 Ω
      I19-3 (MR) or I30-3 (MR+) - Body ground Always 10 kΩ or higher
      I19-11 (MF) or I30-11 (MR-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  5. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (POWER RETRACT FUNCTION)


    1. Remove the outer rear view mirror assembly RH.

      Click here

    2. Inspect the outer rear view mirror assembly RH.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH Click here

    OK

  6. CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - OUTER MIRROR CONTROL ECU ASSEMBLY RH)


    1. Disconnect the I3 outer rear view mirror assembly RH connector.

    2. Disconnect the I15 outer mirror control ECU assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I3-3 (MR) - I15-3 (MR+) Always Below 1 Ω
      I3-11 (MF) - I15-11 (MR-) Always Below 1 Ω
      I3-3 (MR) or I15-3 (MR+) - Body ground Always 10 kΩ or higher
      I3-11 (MF) or I15-11 (MR-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  7. INSPECT OUTER MIRROR SWITCH ASSEMBLY (MIRROR RETRACT SWITCH)


    1. Remove the outer mirror switch assembly.

      Click here

    2. Inspect the outer mirror switch assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE OUTER MIRROR SWITCH ASSEMBLY Click here

    OK

  8. CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])


    1. Disconnect the I27*1 or I11*2 outer mirror switch assembly connector.


      • *1: for LHD


      • *2: for RHD

    2. Disconnect the G62 and G64 main body ECU (multiplex network body ECU) connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      I27-11 (MR) - G62-14 (RET) Always Below 1 Ω
      I27-17 (MAT) - G62-15 (RTR) Always Below 1 Ω
      I27-18 (E) - G64-6 (MIRE) Always Below 1 Ω
      I27-11 (MR) or G62-14 (RET) - Body ground Always 10 kΩ or higher
      I27-17 (MAT) or G62-15 (RTR) - Body ground Always 10 kΩ or higher
      I27-18 (E) or G64-6 (MIRE) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      I11-17 (MR) - G62-14 (RET) Always Below 1 Ω
      I11-11 (MAT) - G62-15 (RTR) Always Below 1 Ω
      I11-10 (E) - G64-6 (MIRE) Always Below 1 Ω
      I11-17 (MR) or G62-14 (RET) - Body ground Always 10 kΩ or higher
      I11-11 (MAT) or G62-15 (RTR) - Body ground Always 10 kΩ or higher
      I11-10 (E) or G64-6 (MIRE) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR