POWER BACK DOOR SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Turn the engine switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the engine switch on (IG).

    4. Turn the GTS on.

    5. Enter the following menus: Body Electrical / Back Door, Main Body or Entry&Start / Data List.

    6. According to the display on the GTS, read the Data List.


      Body Electrical > Back Door > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Door Lock Status Back door condition signal Lock or Unlock

      Lock: Back door locked

      Unlock: Back door unlocked

      		 -
      Half Latch SW Latch switch signal ON or OFF

      ON: Back door lock motor open-latched

      OFF: Back door lock motor full-latched or half-latched

      		 Refer to "POWER BACK DOOR OPERATION TIMING CHART"*1
      Closer Position SW Initial switch signal ON or OFF

      ON: Back door lock sector gear in center position (Initial switch on)

      OFF: Back door lock sector gear out of center position (Initial switch off)

      		 Refer to "POWER BACK DOOR OPERATION TIMING CHART"*1
      Pawl Position Switch Pawl switch signal ON or OFF

      ON: Back door lock motor open-latched

      OFF: Back door lock motor except open-latched

      		 Refer to "POWER BACK DOOR OPERATION TIMING CHART"*1
      Courtesy SW Back door courtesy switch signal ON or OFF

      ON: Back door open

      OFF: Back door closed

      		 Refer to "POWER BACK DOOR OPERATION TIMING CHART"*1
      PBD Touch Sensor (Right) Power back door sensor assembly RH signal ON, OFF or Open

      ON: Power back door sensor assembly RH pressed

      OFF: Power back door sensor assembly RH not pressed

      Open: Power back door sensor assembly RH circuit open

      		 -
      PBD Touch Sensor (Left) Power back door sensor assembly LH signal ON, OFF or Open

      ON: Power back door sensor assembly LH pressed

      OFF: Power back door sensor assembly LH not pressed

      Open: Power back door sensor assembly LH circuit open

      		 -
      PBD Main SW Power slide door main switch ON/OFF signal ON or OFF

      ON: Power slide door main switch on

      OFF: Power slide door main switch off

      		 -
      PBD Close SW Back door control switch signal ON or OFF

      ON: Back door control switch pushed

      OFF: Back door control switch not pushed

      		 -
      IG SW Engine switch signal ON or OFF

      ON: Engine switch on (IG)

      OFF: Engine switch off

      		 "OFF" is also displayed for this item when the engine switch is on (ACC).
      PBD Position (3/4-Open) Load signal detected during back door closing operation (3/4 - Open) Caution or OK

      Caution: Load detected between back door 3/4 and fully open position during back door closing operation

      OK: No load detected between back door 3/4 and fully open position during back door closing operation

      		 -
      PBD Position (2/4-3/4) Load signal detected during back door closing operation (2/4 - 3/4) Caution or OK

      Caution: Load detected between back door 2/4 and 3/4 open position during back door closing operation

      OK: No load detected between back door 2/4 and 3/4 open position during back door closing operation

      		 -
      PBD Position (1/4-2/4) Load signal detected during back door closing operation (1/4 - 2/4) Caution or OK

      Caution: Load detected between back door 1/4 and 2/4 open position during back door closing operation

      OK: No load detected between back door 1/4 and 2/4 open position during back door closing operation

      		 -
      PBD Position (Close-1/4) Load signal detected during back door closing operation (Close - 1/4) Caution or OK

      Caution: Load detected between back door fully closed and 1/4 open position during back door closing operation

      OK: No load detected between back door fully closed and 1/4 open position during back door closing operation

      		 -
      PBD SW Operation Power back door switch operation ON or 0.8 s Current customize setting displayed -
      PBD Buzz In Use Power back door warning buzzer operation condition signal OFF or ON Current customize setting displayed The warning buzzer that sounds when the power back door is operating cannot be customized (even if this function is set to "OFF", the buzzer will still sound).
      Door Unlock with 1 Motion. Door or doors to be unlocked when back door locked and power back door operated by pressing transmitter switch (electrical key transmitter sub-assembly).*2 Back Door or ALL DOORS Current customize setting displayed -
      Wireless Power Back Door Open Function that operates the power back door by pushing the transmitter switch (electrical key transmitter sub-assembly).*3 Lock:OFF/Unlock:OFF, Lock:OFF/Unlock:ON, Lock:OFF/Unlock:Twice, Lock:OFF/Unlock:0.8s, Lock:Twice/Unlock:Twice or Lock:0.8s/Unlock:0.8 Current customize setting displayed -
      #Codes Number of DTCs Min.: 0, Max.: 255

      When system is normal: 0

      When a malfunction is detected: More than 0

      		 -

      • *1: Refer to "POWER BACK DOOR OPERATION TIMING CHART"

        Click here

      • **cut**: ock: 0.8s

      Tech Tips


      • *2: "ALL DOORS" is only available for vehicles with the wireless one motion function.

      • *3: "Lock:Twice/Unlock:Twice" and "Lock:0.8s/Unlock:0.8s" are only available for vehicles with the wireless one motion function.


      Body Electrical > Main Body > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Back Door Open Back door lock Permit or Prohibit

      Permit: Back door unlocked

      Prohibit: Back door locked

      		 -
      Back Door Open SW Map light assembly (power back door switch) signal ON or OFF

      ON: Map light assembly (power back door switch) on

      OFF: Map light assembly (power back door switch) off

      		 -

      Body Electrical > Entry&Start > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Tr/B-Door Unlock SW Back door opener switch assembly (open switch) signal ON or OFF

      ON: Back door opener switch assembly (open switch) on

      OFF: Back door opener switch assembly (open switch) off

      		 -

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Turn the engine switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the engine switch on (IG).

    4. Turn the GTS on.

    5. Enter the following menus: Body Electrical / Back Door / Active Test.

    6. According to the display on GTS perform the "Active Test".


      Body Electrical > Back Door > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Latch Release Latch release operation ON or OFF -
      PBD Motor Power back door motor operation OFF, Forward or Reverse -
      PBD Clutch Clutch operation ON or OFF -
      PBD Buzzer Power back door warning buzzer sound ON or OFF -
      Courtesy SW Signal Back door courtesy light switch output ON or OFF -