TILT ROOF HOUSING REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the tilt roof housing sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Disconnect cable from negative battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and Start System (for 2AR-FE)

Click here

Stop and Start System (for 2GR-FKS)

Click here

Memorize steering angle neutral point Panoramic View Monitor System

Click here

Initialize back door lock Power Door Lock Control System

Click here

Initialize servo motor Air Conditioning System

Click here

Reset slide door close position Power Slide Door System

Click here

Reset back door close position Power Back Door System

Click here

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

B006LSF

Click here

PROCEDURE


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    B006LHC

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE FRONT SLIDING ROOF GARNISH RH


    1. Fully open the sunshade trim sub-assembly.

    2. B006L1N

      Remove the front sliding roof garnish RH.

  4. REMOVE FRONT SLIDING ROOF GARNISH LH

    Tech Tips

    Use the same procedure described for the RH side.

  5. REMOVE TILT ROOF GLASS SUB-ASSEMBLY


    1. Unlock the lock of the tilt roof glass sub-assembly and tilt up the tilt roof glass sub-assembly.

    2. B006M58

      Using a T25 "TORX" socket wrench, remove the 4 screws and tilt roof glass sub-assembly.

      Tech Tips

      The illustration shows the RH side. The vertical orientation of the LH side is opposite that of the image shown in the illustration.

  6. REMOVE ROOF HEADLINING ASSEMBLY

    Click here

  7. REMOVE TELEVISION BRACKET


    1. w/ 9 Inch Television Display:


      1. B006KZE

        Disconnect the sliding roof drive gear connector.

      2. Detach the clamp.

    2. w/ 12 Inch Television Display:


      1. B006MAF

        Disconnect the sliding roof drive gear connector.

      2. Detach the clamp.

    3. w/o Television Display:


      1. B006PHE

        Disconnect the sliding roof drive gear connector.

      2. Detach the clamp.

    4. B006MTP

      Remove the 4 bolts.

    5. Detach the clip and guide and remove the television bracket.

  8. REMOVE TILT ROOF HOUSING SUB-ASSEMBLY


    1. B006MKPC01
      B006N8A Open

      Open the plate to break it as shown in the illustration.

      Note

      When opening the plate to break it, make sure that the tilt roof housing sub-assembly and vehicle body are not damaged.

      Tech Tips

      The plate is used when the vehicle is assembled at the factory and is not needed for reinstallation.

    2. B006RHEC01
      *1 Tilt Roof Drain Hose Assembly
      *2 Sliding Roof Drain Hose

      Disconnect the 2 tilt roof drain hose assemblies and 2 sliding roof drain hoses.

    3. B006KRV

      Remove the 7 nuts and tilt roof housing sub-assembly.

    4. B006QW4C01
      B006N8A Rotate

      Rotate to remove the plate as shown in the illustration.

      Tech Tips

      The plate is used when the vehicle is assembled at the factory and is not needed for reinstallation.

  9. REMOVE TILT ROOF LOCK STRIKER


    1. B006LYR

      Remove the 3 bolts and tilt roof lock striker.

  10. REMOVE TILT ROOF PANEL COVER


    1. B006PX2C01
      B006N8A Remove in this Direction

      Remove the tilt roof panel cover.

  11. REMOVE TILT ROOF LOCK HANDLE ASSEMBLY


    1. B006NXR

      Remove the 2 screws and tilt roof lock handle assembly.

  12. REMOVE TILT ROOF GLASS SEAL


    1. B006P3CC01
      B006N8A Remove in this Direction

      Remove the tilt roof glass seal.

      Note

      Always replace the tilt roof glass seal with a new one.

  13. REMOVE TILT ROOF WEATHERSTRIP


    1. B006ONU

      Remove the tilt roof weatherstrip from the tilt roof glass sub-assembly.