POWER WINDOW CONTROL SYSTEM Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master Switch

DESCRIPTION

If the manual up and down function operates normally but the auto up and down function does not, then fail-safe mode may be functioning.

If power window initialization has not been performed, the auto up and down function will not operate.

Click here

WIRING DIAGRAM

B006KQZE02

CAUTION / NOTICE / HINT

Note


  • The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

    Click here

  • If the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) has been replaced with a new one, initialize the power window control system.

    Click here

  • Check that the "D Window Auto Up" and "D Window Auto Down" power window control system customize settings are "ON" before proceeding with work.

    Click here

  • After the catch protection function operates, the auto operation is not performed the first time auto up is performed. All auto up operations performed after the first operate normally.

Tech Tips

If the pulse sensor built into the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) is malfunctioning, the power window control system enters fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the multiplex network master switch assembly at the auto up position, and opened manually by pushing down the multiplex network master switch assembly.

Click here

PROCEDURE


  1. READ VALUE USING GTS (MASTER SWITCH)


    1. Read the Data List according to the display on the GTS.

      Click here


      Body Electrical > Master Switch > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      D Door P/W Auto SW Driver door power window auto switch signal OFF or ON

      OFF: Driver door power window auto switch not being operated

      ON: Driver door power window auto switch being operated

      		 -

      Body Electrical > Master Switch > Data List
      Tester Display
      D Door P/W Auto SW
      OK
      On the GTS screen, ON or OFF is displayed accordingly.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY Click here

    OK

  2. READ VALUE USING GTS (D-DOOR MOTOR)


    1. Read the Data List according to the display on the GTS.

      Click here


      Body Electrical > D-Door Motor > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      D Door P/W Auto SW Driver door power window auto switch signal OFF or ON

      OFF: Driver door power window auto switch not being operated

      ON: Driver door power window auto switch being operated

      		 -

      Body Electrical > D-Door Motor > Data List
      Tester Display
      D Door P/W Auto SW
      OK
      On the GTS screen, ON or OFF is displayed accordingly.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY Click here

    OK

  3. PERFORM INITIALIZATION (FOR DRIVER DOOR)


    1. Initialize the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD).

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  4. CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION)


    1. Check that the driver door power window moves when the auto up and down function of the multiplex network master switch assembly is operated.

      Click here

      OK
      Driver door auto up and down function is normal.
      Result
      Result Proceed to
      OK A
      NG (for LHD) B
      NG (for RHD) C

    A

    END (PROBLEM DUE TO INITIALIZATION FAILURE)

    B

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH Click here

    C

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH Click here

  5. REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY


    1. Replace the multiplex network master switch assembly.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  6. CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION)


    1. Check that the driver door power window moves when the auto up and down function of the multiplex network master switch assembly is operated.

      Click here

      OK
      Driver door auto up and down function is normal.
      Result
      Result Proceed to
      OK A
      NG (for LHD) B
      NG (for RHD) C

    A

    END (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WAS DEFECTIVE)

    B

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH Click here

    C

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH Click here