ROOF HEADLINING INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • A bolt without a torque specification is shown in the standard bolt chart.

    Click here

PROCEDURE


  1. INSTALL FRONT ROOF HEADLINING TRIM SUB-ASSEMBLY (for Normal Roof)


    1. B006MSPC01
      B006N8A Movement Direction

      Insert the front roof headlining trim sub-assembly into the cabin from the back door.

      Note


      • Check that the corners of the front roof headlining trim sub-assembly are not folded, twisted or otherwise deformed and that none of the mounted parts have fallen off.

      • Make sure that the front roof headlining trim sub-assembly does not get caught on anything as it may become bent or damaged.

      • Do not damage the front roof headlining trim sub-assembly or vehicle interior.

    2. w/o Rear Entertainment System:

      Attach the guide, fastener and clip to install the front roof headlining trim sub-assembly.

      B006ONEC02
      *a Guide *b Fastener

    3. w/ Rear Entertainment System:

      Attach the guide, fastener and clip to install the front roof headlining trim sub-assembly.

      B006KT2C02
      *a Guide *b Fastener
    4. B006MI0C01
      *1 Washer Hose
      *a Connector

      Connect the connector and washer hose and attach the clamp to the rear pillar RH.

    5. B006N10C02
      *1 Washer Hose
      *a Connector
      *b Bolt

      Connect the connector and washer hose and attach the clamp to the front pillar RH.

    6. Install the bolt.

    7. B006NF5

      Connect the connector and attach the clamp to the front pillar LH.

  2. INSTALL FRONT ROOF HEADLINING TRIM SUB-ASSEMBLY (for Sliding Roof)


    1. B006Q02C01
      B006N8A Movement Direction

      Insert the front roof headlining trim sub-assembly into the cabin from the back door.

      Note


      • Check that the corners of the front roof headlining trim sub-assembly are not folded, twisted or otherwise deformed and that none of the mounted parts have fallen off.

      • Make sure that the front roof headlining trim sub-assembly does not get caught on anything as it may become bent or damaged.

      • Do not damage the front roof headlining trim sub-assembly or vehicle interior.

    2. w/o Rear Entertainment System:

      Attach the guide, fastener, claw and clip to install the front roof headlining trim sub-assembly.

      B006RBTC02
      *a Guide *b Fastener

    3. w/ Rear Entertainment System:

      Attach the guide, fastener, claw and clip to install the front roof headlining trim sub-assembly.

      B006LIHC02
      *a Guide *b Fastener
    4. B006NMAC01
      *1 Rear Sliding Roof Drain Hose LH

      Connect the rear sliding roof drain hose LH.

    5. B006L9DC01
      *1 Washer Hose
      *2 Rear Sliding Roof Drain Hose RH
      *a Connector

      Connect the connector, washer hose and rear sliding roof drain hose RH and attach the clamp to the rear pillar RH.

    6. B006N10C03
      *1 Washer Hose
      *a Connector
      *b Bolt

      Connect the connector and washer hose and attach the clamp to the front pillar RH.

    7. Install the bolt.

    8. B006NF5

      Connect the connector and attach the clamp to the front pillar LH.

    9. B006LP3C01
      *A w/ EC Mirror
      *B w/ Rain Sensor

      Connect the connector.

  3. INSTALL TELEVISION BASE (w/ Rear Entertainment System)


    1. B006QE1C01
      B006N8A Install in this Direction

      for 12 Inch:

      Attach the guide, claw and clip to install the television base as shown in the illustration.

    2. B006KW0C01
      B006N8A Install in this Direction

      for 8 Inch:

      Attach the claw and clip to install the television base as shown in the illustration.

  4. INSTALL REAR ROOF SIDE RAIL GARNISH LH


    1. B006QOPC01
      B006N8A Install in this Direction

      Attach the clip to install the rear roof side rail garnish LH as shown in the illustration.

    2. B006NC5C01
      B006N8A Install in this Direction

      w/ Sunshade:

      Attach the claw as shown in the illustration.

      Tech Tips

      Use the same procedure for both sunshade hooks.

  5. INSTALL REAR ROOF SIDE RAIL GARNISH RH


    1. B006RECC01
      B006N8A Install in this Direction

      Attach the clip to install the rear roof side rail garnish RH as shown in the illustration.

    2. B006PBPC01
      B006N8A Install in this Direction

      w/ Sunshade:

      Attach the claw as shown in the illustration.

      Tech Tips

      Use the same procedure for both sunshade hooks.

  6. INSTALL FRONT ROOF SIDE RAIL GARNISH LH


    1. B006QN1C01
      B006N8A Install in this Direction

      Attach the clip to install the front roof side rail garnish LH as shown in the illustration.

  7. INSTALL FRONT ROOF SIDE RAIL GARNISH RH


    1. B006PGGC01
      B006N8A Install in this Direction

      Attach the clip to install the front roof side rail garnish RH as shown in the illustration.

  8. INSTALL NO. 1 COOLER AIR DUCT

    Click here

  9. INSTALL COOLER PLATE

    Click here

  10. INSTALL SEAT BELT ANCHOR COVER


    1. B006QOLC01
      B006N8A Install in this Direction

      Attach the guide, claw and clip to install the seat belt anchor cover as shown in the illustration.

  11. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY

    Click here

  12. INSTALL REAR ASSIST GRIP ASSEMBLY LH


    1. B006RLU

      Install the 2 clips and 2 assist grip covers to the rear assist grip.

      Tech Tips

      Temporarily install the assist grip covers.

    2. B006NWHC01
      B006N8A Install in this Direction

      Attach the clip.

    3. Push in the assist grip covers to install the rear assist grip assembly LH.

  13. INSTALL REAR ASSIST GRIP ASSEMBLY RH


    1. B006LUV

      Install the 2 clips and 2 assist grip covers to the rear assist grip.

      Tech Tips

      Temporarily install the assist grip covers.

    2. B006RKMC01
      B006N8A Install in this Direction

      Attach the clip.

    3. Push in the assist grip covers to install the rear assist grip assembly RH.

  14. INSTALL ASSIST GRIP SUB-ASSEMBLY

    Tech Tips

    Use the same procedure for both assist grip sub-assemblies.


    1. B006LHD

      Install the 2 clips and 2 assist grip covers to the rear assist grip.

      Tech Tips

      Temporarily install the assist grip covers.

    2. B006RIWC01
      B006N8A Install in this Direction

      Attach the clip.

    3. Push in the assist grip covers to install the assist grip sub-assembly.

  15. INSTALL RAIN SENSOR COVER (w/ Rain Sensor)

    Click here

  16. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

    Click here

  17. INSTALL VISOR HOLDER

    Tech Tips

    Use the same procedure for both visor holders.


    1. B006LV7

      Attach the claw.

    2. B006KNKC01
      B006N8A Install in this Direction

      Push in the visor holder to install it.

  18. INSTALL VISOR ASSEMBLY LH


    1. B006P9PC03
      *1 Visor Holder

      Install the visor assembly LH with the 2 screws.

    2. Connect the visor assembly LH to the visor holder.

  19. INSTALL VISOR ASSEMBLY RH


    1. B006NL3C03
      *1 Visor Holder

      Install the visor assembly RH with the 2 screws.

    2. Connect the visor assembly RH to the visor holder.

  20. INSTALL VISOR BRACKET COVER LH


    1. B006N3UC01
      B006N8A Install in this Direction

      Attach the claw to install the visor bracket cover LH as shown in the illustration.

  21. INSTALL VISOR BRACKET COVER RH


    1. B006Q2PC01
      B006N8A Install in this Direction

      Attach the claw to install the visor bracket cover RH as shown in the illustration.

  22. INSTALL MAP LIGHT ASSEMBLY


    1. for LED Type:

      Click here

    2. for Bulb Type:

      Click here

  23. INSTALL INNER UPPER ROOF SIDE GARNISH LH


    1. B006M17C01
      B006N8A Install in this Direction

      w/ Power Back Door:

      Pass the power back door rod through the inner upper roof side garnish LH.

    2. B006KQTC01
      B006N8A Install in this Direction

      Attach the guide, claw and clip to install the inner upper roof side garnish LH as shown in the illustration.

    3. B006MOR

      Install the 2 bolts.

    4. B006LGWC01
      B006N8A Cover Closing Direction

      Connect the rear No. 2 seat outer belt assembly LH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    5. Attach the claw to close the cover.

    6. w/ Power Back Door:

      Connect the power back door rod.

      Click here

  24. INSTALL INNER UPPER ROOF SIDE GARNISH RH


    1. B006M14C01
      B006N8A Install in this Direction

      Attach the guide, claw and clip to install the inner upper roof side garnish RH as shown in the illustration.

    2. B006KWL

      Install the 2 bolts.

    3. B006LGWC01
      B006N8A Cover Closing Direction

      Connect the rear No. 2 seat outer belt assembly RH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    4. Attach the claw to close the cover.

  25. INSTALL BACK DOOR SIDE GARNISH LH (w/ Power Back Door)

    Click here

  26. INSTALL BACK DOOR SERVICE HOLE COVER LH (w/ Power Back Door)

    Click here

  27. INSTALL CENTER BACK DOOR GARNISH (w/ Power Back Door)

    Click here

  28. INSTALL QUARTER LOCK PILLAR GARNISH LH


    1. B006LP0C01
      B006N8A Install in this Direction

      Attach the guide, claw and clip to install the quarter lock pillar garnish LH as shown in the illustration.

    2. B006OOSC03
      *1 No. 1 Slide Door Weatherstrip LH

      Connect the No. 1 slide door weatherstrip LH in the range shown in the illustration.

  29. INSTALL QUARTER LOCK PILLAR GARNISH RH


    1. B006OHGC01
      B006N8A Install in this Direction

      Attach the guide, claw and clip to install the quarter lock pillar garnish RH as shown in the illustration.

    2. B006PWIC02
      *1 No. 1 Slide Door Weatherstrip RH

      Connect the No. 1 slide door weatherstrip RH in the range shown in the illustration.

  30. INSTALL REAR QUARTER TRIM PANEL ASSEMBLY LH


    1. Connect the connector.

    2. Attach the claw and clip to install the rear quarter trim panel assembly LH as shown in the illustration.

      B006P3WC01
      B006N8A Install in this Direction - -
    3. B006OYM

      Install the screw.

    4. B006MMUC03
      *1 No. 1 Slide Door Weatherstrip LH

      Connect the No. 1 slide door weatherstrip LH in the range shown in the illustration.

  31. INSTALL REAR QUARTER TRIM PANEL ASSEMBLY RH


    1. Connect the connector.

    2. Attach the claw and clip to install the rear quarter trim panel assembly RH as shown in the illustration.

      B006LAJC02
      B006N8A Install in this Direction - -
    3. B006MQ6

      Install the screw.

    4. B006Q3PC03
      *1 No. 1 Slide Door Weatherstrip RH

      Connect the No. 1 slide door weatherstrip RH in the range shown in the illustration.

  32. INSTALL ROPE HOOK ASSEMBLY

    Tech Tips

    Use the same procedure for both rope hook assemblies.


    1. B006O14

      Install the rope hook assembly with the bolt.

    2. B006O13

      Attach the claw to close the cover.

  33. INSTALL NO. 2 LUGGAGE COMPARTMENT TRIM HOOK


    1. B006PHZC01
      B006N8A Install in this Direction

      Turn the end of the No. 2 luggage compartment trim hook horizontal, and then install the No. 2 luggage compartment trim hook.

  34. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    1. B006MIPC01
      B006N8A Install in this Direction

      Turn the end of the No. 1 luggage compartment trim hook horizontal, and then install the No. 1 luggage compartment trim hook.

  35. INSTALL DECK SIDE GARNISH LH


    1. Attach the claw to install the deck side garnish LH as shown in the illustration.

      B006O34C01
      B006N8A Install in this Direction - -

  36. INSTALL DECK SIDE GARNISH RH


    1. Attach the claw to install the deck side garnish RH as shown in the illustration.

      B006P8YC01
      B006N8A Install in this Direction - -

  37. INSTALL REAR UPPER NO. 2 FLOOR BOARD PLATE


    1. B006MR6C01
      B006N8A Install in this Direction

      Attach the guide, claw and clip to install the rear upper No. 2 floor board plate as shown in the illustration.

    2. B006MFJC01
      *a Alignment Mark
      B006Q1Z Press Position of the Rear Seat Track Slide Stopper
      B006N8A Slide Direction

      Press the part of the rear seat track slide stopper shown in the illustration, slide the rear seat track slide stopper in the direction indicated by the arrow and align the alignment marks.

    3. B006KW1C01
      *a Protective Tape
      B006Q1Z Lock Position

      Using a screwdriver, return the lock of the rear seat track slide stopper to its original condition.

      Tech Tips

      Tape the screwdriver tip before use.

  38. INSTALL REAR UPPER NO. 1 FLOOR BOARD PLATE


    1. B006M95C01
      B006N8A Install in this Direction

      Attach the guide, claw and clip to install the rear upper No. 1 floor board plate as shown in the illustration.

    2. B006KOLC01
      *a Alignment Mark
      B006Q1Z Press Position of the Rear Seat Track Slide Stopper
      B006N8A Slide Direction

      Press the part of the rear seat track slide stopper shown in the illustration, slide the rear seat track slide stopper in the direction indicated by the arrow and align the alignment marks.

    3. B006MPUC01
      *a Protective Tape
      B006Q1Z Lock Position

      Using a screwdriver, return the lock of the rear seat track slide stopper to its original condition.

      Tech Tips

      Tape the screwdriver tip before use.

  39. INSTALL BACK DOOR SCUFF PLATE


    1. Attach the guide, claw and clip to install the back door scuff plate as shown in the illustration.

      B006RCXC01
      B006N8A Install in this Direction - -

  40. INSTALL UTILITY BOX SUB-ASSEMBLY


    1. B006KL8C01
      B006N8A Install in this Direction

      Attach the guide and claw to install the utility box sub-assembly as shown in the illustration.

  41. INSTALL REAR NO. 3 FLOOR BOARD ASSEMBLY


    1. B006QKJC01
      B006N8A Install in this Direction

      Attach the guide to install the rear No. 3 floor board assembly as shown in the illustration.

  42. INSTALL REAR NO. 2 FLOOR BOARD ASSEMBLY


    1. B006QAVC01
      B006N8A Install in this Direction

      Attach the guide to install the rear No. 2 floor board assembly as shown in the illustration.

  43. INSTALL REAR NO. 1 FLOOR BOARD ASSEMBLY


    1. B006LQ6C01
      B006N8A Install in this Direction

      Attach the guide to install the rear No. 1 floor board assembly as shown in the illustration.

  44. INSTALL CENTER PILLAR GARNISH LH

    Tech Tips

    Move the front shoulder belt anchor adjuster and shoulder belt anchor cover to the lowest position and install the center pillar garnish LH.


    1. Pass the front seat outer belt floor anchor through the center pillar garnish LH.

    2. B006L64C01
      B006N8A Install in this Direction

      Attach the claw and clip to install the center pillar garnish LH as shown in the illustration.

    3. B006O3WC03
      *1 Front Door Opening Trim Weatherstrip LH
      *2 No. 1 Slide Door Weatherstrip LH

      Connect the front door opening trim weatherstrip LH and No. 1 slide door weatherstrip LH in the range shown in the illustration.

  45. INSTALL CENTER PILLAR GARNISH RH

    Tech Tips

    Move the front shoulder belt anchor adjuster and shoulder belt anchor cover to the lowest position and install the center pillar garnish RH.


    1. Pass the front seat outer belt floor anchor through the center pillar garnish RH.

    2. B006Q0JC01
      B006N8A Install in this Direction

      Attach the claw and clip to install the center pillar garnish RH as shown in the illustration.

    3. B006O3QC02
      *1 Front Door Opening Trim Weatherstrip RH
      *2 No. 1 Slide Door Weatherstrip RH

      Connect the front door opening trim weatherstrip RH and No. 1 slide door weatherstrip RH in the range shown in the illustration.

  46. INSTALL LOWER CENTER PILLAR GARNISH LH


    1. B006PYOC01
      B006N8A Install in this Direction

      Attach the claw and clip to install the lower center pillar garnish LH as shown in the illustration.

    2. B006PRN

      except Super Long Slide Seat:

      Connect the front seat outer belt assembly LH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    3. B006NU9C04
      *1 Front Door Opening Trim Weatherstrip LH
      *2 No. 1 Slide Door Weatherstrip LH

      Connect the front door opening trim weatherstrip LH and No. 1 slide door weatherstrip LH in the range shown in the illustration.

  47. INSTALL LOWER CENTER PILLAR GARNISH RH


    1. B006PRLC01
      B006N8A Install in this Direction

      Attach the claw and clip to install the lower center pillar garnish RH as shown in the illustration.

    2. B006RDU

      Connect the front seat outer belt assembly RH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    3. B006NU0C03
      *1 Front Door Opening Trim Weatherstrip RH
      *2 No. 1 Slide Door Weatherstrip RH

      Connect the front door opening trim weatherstrip RH and No. 1 slide door weatherstrip RH in the range shown in the illustration.

  48. INSTALL OUTER LAP BELT ANCHOR COVER

    Tech Tips


    • Use the same procedure for outer lap belt anchor covers.

    • For the LH side, use the same procedure for vehicles without super long slide seat.


    1. B006MERC01
      B006N8A Install in this Direction

      Attach the claw to install the outer lap belt anchor cover as shown in the illustration.

  49. INSTALL NO. 2 ASSIST GRIP


    1. B006PUB

      Install the No. 2 assist grip with the 3 bolts.

  50. INSTALL NO. 1 ASSIST GRIP


    1. B006OON

      Install the No. 1 assist grip with the 3 bolts.

  51. INSTALL ASSIST GRIP PLUG

    Tech Tips

    Use the same procedure for both assist grip plugs.


    1. B006ODHC01
      B006N8A Install in this Direction

      Attach the claw to install the assist grip plug as shown in the illustration.

  52. INSTALL ASSIST GRIP PLUG

    Tech Tips

    Use the same procedure for all assist grip plugs.


    1. B006KYSC01
      B006N8A Install in this Direction

      Attach the claw to install the assist grip plug as shown in the illustration.

  53. INSTALL REAR DOOR SCUFF PLATE LH


    1. Attach the guide, claw and clip to install the rear door scuff plate LH as shown in the illustration.

      B006RKBC01
      B006N8A Install in this Direction - -

  54. INSTALL REAR DOOR SCUFF PLATE RH


    1. Attach the guide, claw and clip to install the rear door scuff plate RH as shown in the illustration.

      B006MY9C01
      B006N8A Install in this Direction - -

  55. INSTALL DOOR SCUFF PLATE ASSEMBLY LH


    1. except Super Long Slide Seat:


      1. B006OW1C01
        B006N8A Install in this Direction

        Attach the claw and clip to install the door scuff plate assembly LH as shown in the illustration.

    2. for Super Long Slide Seat:


      1. B006PNOC01
        B006N8A Install in this Direction

        Attach the claw and clip to install the door scuff plate assembly LH as shown in the illustration.

  56. INSTALL DOOR SCUFF PLATE ASSEMBLY RH


    1. B006OWHC01
      B006N8A Install in this Direction

      Attach the claw and clip to install the door scuff plate assembly RH as shown in the illustration.

  57. INSTALL COWL SIDE TRIM BOARD LH


    1. B006LYAC01
      *a Cap Nut
      B006N8A Install in this Direction

      Attach the guide, claw and clip to install the cowl side trim board LH as shown in the illustration.

    2. Install the cap nut.

  58. INSTALL COWL SIDE TRIM BOARD RH


    1. B006O1UC01
      *a Cap Nut
      B006N8A Install in this Direction

      Attach the guide, claw and clip to install the cowl side trim board RH as shown in the illustration.

    2. Install the cap nut.

  59. INSTALL LOWER FRONT PILLAR GARNISH LH


    1. B006MJMC01
      B006N8A Install in this Direction

      Attach the claw to install the lower front pillar garnish LH as shown in the illustration.

  60. INSTALL LOWER FRONT PILLAR GARNISH RH


    1. B006NX4C01
      B006N8A Install in this Direction

      Attach the claw to install the lower front pillar garnish RH as shown in the illustration.

  61. INSTALL FRONT PILLAR GARNISH LH


    1. B006MZAC01
      B006N8A Install in this Direction (1)
      B006NJK Install in this Direction (2)

      Attach the guide and clip to install the front pillar garnish LH as shown in the illustration.

    2. B006Q3IC02
      *1 Front Door Opening Trim Weatherstrip LH

      Connect the front door opening trim weatherstrip LH in the range shown in the illustration.

  62. INSTALL FRONT PILLAR GARNISH RH


    1. B006PJIC01
      B006N8A Install in this Direction (1)
      B006NJK Install in this Direction (2)

      Attach the guide and clip to install the front pillar garnish RH as shown in the illustration.

    2. B006QDFC01
      *1 Front Door Opening Trim Weatherstrip RH

      Connect the front door opening trim weatherstrip RH in the range shown in the illustration.

  63. INSTALL PILLAR ASSIST GRIP ASSEMBLY

    Tech Tips

    Use the same procedure for both pillar assist grip assemblies.


    1. B006QJ3

      Install the pillar assist grip assembly with the 2 bolts.

  64. INSTALL ASSIST GRIP PLUG

    Tech Tips

    Use the same procedure for both assist grip plugs.


    1. B006MOPC01
      B006N8A Install in this Direction

      Attach the claw to install the 2 assist grip plugs as shown in the illustration.

  65. INSTALL REAR NO. 2 SEAT ASSEMBLY LH

    Click here

  66. INSTALL REAR NO. 2 SEAT ASSEMBLY RH

    Click here

  67. FILL UP WINDSHIELD WASHER JAR WITH WASHER FLUID

    Click here

  68. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

    Click here

  69. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  70. CHECK SRS WARNING LIGHT

    Click here