INSTRUMENT PANEL SAFETY PAD(for LHD) INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips

A bolt without a torque specification is shown in the standard bolt chart.

Click here

PROCEDURE


  1. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY


    1. B006QWDC01
      B006N8A Movement Direction

      Insert the instrument panel safety pad assembly into the vehicle from the slide door opening.

      Note


      • Make sure that the instrument panel safety pad assembly does not get caught on anything as it may become bent or damaged.

      • Do not damage the instrument panel safety pad assembly or vehicle interior.

    2. B006PO7C01
      B006N8A Movement Direction

      Set the instrument panel safety pad assembly on the instrument panel reinforcement assembly.

    3. w/o Navigation System:


      1. Attach the guide to install the instrument panel safety pad assembly.

      2. Install the 2 passenger airbag installation bolts <H>.

        Torque:
        20 N*m  { 204 kgf*cm, 15 ft.*lbf }

      3. Install the 8 bolts <A>, 2 clips <F> and 4 nuts <G>.

      4. Connect the connector and attach the clamp.

        B006LNAC02
        *a Guide *b Passenger Airbag Installation Bolt <H>
        *c Bolt <A> *d Clip <F>
        *e Nut <G> *f Connector
        *g Clamp *h Passenger Airbag Connector
      5. B006PD0C03
        *a Lock Slider
        *b Lock Position

        Connect the passenger airbag connector.

        Note

        When handling the passenger airbag connector, take care not to damage the airbag wire harness.

      6. Check that the lock slider is in the lock position.

    4. w/ Navigation System:


      1. Attach the guide to install the instrument panel safety pad assembly.

      2. Install the 2 passenger airbag installation bolts <H>.

        Torque:
        20 N*m  { 204 kgf*cm, 15 ft.*lbf }

      3. Install the 8 bolts <A>, 2 clips <F> and 4 nuts <G>.

      4. Connect the connector and attach the clamp.

        B006ONRC03
        *a Guide *b Passenger Airbag Installation Bolt <H>
        *c Bolt <A> *d Clip <F>
        *e Nut <G> *f Connector
        *g Clamp *h Passenger Airbag Connector
      5. B006PD0C03
        *a Lock Slider
        *b Lock Position

        Connect the passenger airbag connector.

        Note

        When handling the passenger airbag connector, take care not to damage the airbag wire harness.

      6. Check that the lock slider is in the lock position.

  2. INSTALL SHIFT LEVER ASSEMBLY

    Click here

  3. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

    Click here

  4. INSTALL LOWER FRONT PILLAR GARNISH LH

    Click here

  5. INSTALL LOWER FRONT PILLAR GARNISH RH

    Click here

  6. INSTALL FRONT PILLAR GARNISH LH

    Click here

  7. INSTALL FRONT PILLAR GARNISH RH

    Click here

  8. INSTALL PILLAR ASSIST GRIP ASSEMBLY

    Click here

  9. INSTALL ASSIST GRIP PLUG

    Click here

  10. INSTALL LOWER INSTRUMENT PANEL


    1. B006QULC01
      B006N8A Install in this Direction

      Attach the claw to install the lower instrument panel as shown in the illustration.

    2. B006OHVC02
      *a Connector
      *b Bolt <A>
      *c Screw <C>
      *d Screw <D>

      Connect the connector.

    3. Install the 2 bolts <A>, 4 screws <C> and screw <D>.

  11. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    1. B006LKUC01
      *a Screw <C>
      *b Clip <E>
      B006N8A Install in this Direction

      Attach the claw to install the lower No. 1 instrument panel finish panel as shown in the illustration.

    2. Install the screw <C> and clip <E>.

  12. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. B006NW3C01
      B006N8A Install in this Direction

      Connect the connector.

    2. Attach the guide and claw to install the No. 2 instrument panel under cover sub-assembly as shown in the illustration.

  13. INSTALL COWL SIDE TRIM BOARD RH

    Click here

  14. INSTALL NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. B006LYCC01
      B006N8A Install in this Direction

      for VIP Captain Seat:


      1. Attach the claw to install the No. 3 instrument cluster finish panel garnish as shown in the illustration.

    2. B006KKCC01
      B006N8A Install in this Direction

      except VIP Captain Seat:


      1. Attach the claw to install the No. 3 instrument cluster finish panel garnish as shown in the illustration.

  15. INSTALL GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY


    1. B006LTZ

      Attach the claw to install the glove compartment door stopper sub-assembly.

  16. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


    1. B006OF9C01
      *a Hinge

      Attach the hinge.

    2. Press the parts labeled A in the illustration in the direction indicated by the arrows and attach the stoppers to install the glove compartment door assembly.

    3. Attach the claw to connect the glove compartment door stopper sub-assembly.

  17. INSTALL INSTRUMENT PANEL CUP HOLDER


    1. B006PD6C01
      *a Screw <B>
      B006N8A Install in this Direction

      Attach the claw to install the instrument panel cup holder as shown in the illustration.

    2. Install the 2 screws <B>.

  18. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. B006Q55

      Attach the guide and claw to connect the hood lock control lever sub-assembly and fuel lid lock open lever to the lower instrument panel finish panel assembly.

    2. Connect the connector.

    3. B006PVBC01
      *a Bolt <A>
      B006N8A Install in this Direction

      Attach the claw to install the lower instrument panel finish panel assembly as shown in the illustration.

    4. Install the 2 bolts <A>.

  19. INSTALL NO. 1 SWITCH HOLE BASE


    1. B006N5ZC01
      B006N8A Install in this Direction

      Connect the connector.

    2. Attach the claw to install the No. 1 switch hole base as shown in the illustration.

  20. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  21. INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL


    1. B006M06C01
      *a Clip <E>
      B006N8A Install in this Direction

      Attach the claw to install the lower No. 2 instrument panel finish panel as shown in the illustration.

    2. Install the clip <E>.

  22. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. B006L46C01
      *a Screw <B>
      B006N8A Install in this Direction

      Connect the connector.

    2. Attach the guide and claw to install the No. 1 instrument panel under cover sub-assembly as shown in the illustration.

    3. Install the 2 screws <B>.

  23. INSTALL COWL SIDE TRIM BOARD LH

    Click here

  24. INSTALL COMBINATION METER ASSEMBLY


    1. B006NYRC01
      B006N8A Install in this Direction

      Connect the connector and attach the clamp.

    2. Attach the claw to install the combination meter assembly as shown in the illustration.

  25. INSTALL INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. B006P4SC01
      B006N8A Install in this Direction

      Connect the connector.

    2. Attach the claw to install the instrument panel finish panel assembly as shown in the illustration.

  26. INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. B006MTBC01
      B006N8A Install in this Direction

      Connect the connector.

    2. Attach the claw to install the lower center instrument cluster finish panel sub-assembly as shown in the illustration.

  27. INSTALL COMBINATION SWITCH ASSEMBLY

    Click here

  28. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


    1. B006LG8C01
      B006N8A Install in this Direction

      Install the shift lever knob sub-assembly and twist it in the direction indicated by the arrow.

  29. INSTALL AIR CONDITIONING CONTROL ASSEMBLY

    Click here

  30. INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Audio, w/o Navigation System)

    Click here

  31. INSTALL NAVIGATION RECEIVER ASSEMBLY (w/ Audio, w/ Navigation System)

    Click here

  32. INSTALL RADIO TUNER OPENING COVER (w/o Audio)


    1. B006MGQ

      Install the radio tuner opening cover with the 4 screws.

  33. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Audio)


    1. B006LLVC01
      B006N8A Install in this Direction

      Connect the connector.

    2. Attach the claw to install the center instrument cluster finish panel sub-assembly as shown in the illustration.

  34. INSTALL NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY (w/ Audio)


    1. B006PUSC01
      B006N8A Install in this Direction

      Attach the claw to install the No. 4 instrument panel register assembly as shown in the illustration.

  35. INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY (w/ Audio)


    1. B006N9YC01
      B006N8A Install in this Direction

      Attach the claw to install the No. 3 instrument panel register assembly as shown in the illustration.

  36. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL


    1. B006O1TC01
      B006N8A Install in this Direction

      Attach the claw to install the upper instrument panel finish panel as shown in the illustration.

  37. INSTALL HEADLIGHT DIMMER SWITCH ASSEMBLY

    Click here

  38. INSTALL CONSOLE BOX ASSEMBLY

    Click here

  39. INSTALL REAR NO. 1 SEAT ASSEMBLY LH


    1. for Power Captain Seat without Memory:

      Click here

    2. for Power Captain Seat with Memory:

      Click here

  40. INSTALL REAR NO. 1 SEAT ASSEMBLY RH


    1. for Power Captain Seat without Memory:

      Click here

    2. for Power Captain Seat with Memory:

      Click here

  41. INSTALL FRONT SEAT ASSEMBLY LH

    Click here

  42. INSTALL FRONT SEAT ASSEMBLY RH

    Click here

  43. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  44. CHECK SRS WARNING LIGHT

    Click here