FRONT SEAT ASSEMBLY(for Super Long Slide Seat) REMOVAL

CAUTION / NOTICE / HINT

Additional Work After Servicing
Replacement Part or Procedure Necessary Procedures Effects/Inoperative Functions when not Performed Link
Disconnect cable from negative (-) battery terminal Drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes) Stop and start system

Click here

Correct the steering angle neutral point Panoramic view monitor system

Click here

Servo motor initialization Air conditioning system

Click here

Reset slide door close position Power slide door system

Click here

Reset back door close position Back door opener

Click here

Initialize back door lock Initialize back door lock

Click here

CAUTION:


  • B006LWS

    Wear protective gloves. Sharp areas on the parts may injure your hands.

  • There is risk of injury.

  • If the front seat side airbag was deployed, replace the front seat airbag assembly, separate type front seatback frame sub-assembly, separate type front seatback cover and separate type front seatback pad with the necessary parts in accordance with the extent of the collision damage.

  • Replace any other damaged parts as necessary.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing.

    B006M99

    Click here

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Click here

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE NO.1 SEAT LEG COVER SUB-ASSEMBLY (for Front Seat Rear Side)


    1. Keep the rear No. 2 seat assembly LH flipped up.

    2. B006LYTC01
      B006N8A Removal in this Direction

      Operate the seat track handle control lever LH of the rear No. 1 seat assembly LH in the direction indicated by the arrow to move the rear No. 1 seat assembly LH to the rearmost position.

    3. Operate the seat track handle control lever LH of the rear No. 1 seat assembly LH again in the direction indicated by the arrow to move the rear No. 1 seat assembly LH to the right side of the vehicle and then further back to the rearmost position.

    4. Operate the seat track lock open lever LH of the front seat assembly LH to slide the front seat assembly LH to the rear No. 1 seat assembly LH center position.

    5. B006NA8C01
      B006N8A Removal in this Direction (1)
      B006NJK Removal in this Direction (2)
      B006PCE Protective Tape

      Outer Side:


      1. Using a screwdriver with its tip wrapped in protective tape, detach the claw and open the No. 1 seat leg cover in removal direction (1) as shown in the illustration.

      2. Pull in removal direction (2) shown in the illustration to detach the hook and remove the No. 1 seat leg cover.

    6. B006QZPC01
      B006N8A Removal in this Direction (1)
      B006NJK Removal in this Direction (2)
      B006PCE Protective Tape

      Inner Side:


      1. Using a screwdriver with its tip wrapped in protective tape, detach the claw and open the No. 1 seat leg cover in removal direction (1) as shown in the illustration.

      2. Pull in removal direction (2) shown in the illustration to detach the hook and remove the No. 1 seat leg cover.

  4. REMOVE NO.1 SEAT LEG COVER SUB-ASSEMBLY (for Front Seat Front Side)


    1. B006L90

      Operate the front seat cushion lever in the direction indicated by the arrow to move the ottoman of the front seat assembly LH to the uppermost position.

    2. B006QTUC02
      B006N8A Removal in this Direction (1)
      B006NJK Removal in this Direction (2)
      B006PCE Protective Tape

      Using a screwdriver with its tip wrapped in protective tape, detach the claw and open the No. 1 seat leg cover in removal direction (1) as shown in the illustration.

    3. Pull in removal direction (2) shown in the illustration to detach the hook and remove the No. 1 seat leg cover.

  5. REMOVE FRONT SEAT LOWER CUSHION SHIELD


    1. B006QEBC01
      B006Q1Z Place Hand Here
      B006N8A Removal in this Direction

      Place your hands at the positions shown in the illustration and pull in the removal direction shown in the illustration to detach the claw and guide.

    2. B006PMZC01
      B006Q1Z Place Hand Here
      B006N8A Removal in this Direction

      Place your hands at the positions shown in the illustration and pull in the removal direction shown in the illustration to detach the claw and guide and remove the front seat lower cushion shield.

  6. REMOVE FRONT SEAT ASSEMBLY LH


    1. B006N5J

      Remove the 2 bolts on the front side of the front seat assembly LH.

    2. B006Q80

      Remove the 2 bolts on the rear side of the front seat assembly LH.

    3. Operate the reclining adjuster release handle LH to set the seatback of the front seat assembly LH to the perpendicular position.

    4. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:


      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

      B006LHC

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here

    5. B006OJD

      Disconnect the front seat airbag assembly LH connector.


      1. Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

        B006PX0C03
        *1 White Housing Lock - -
        *a Push *b Slide

    6. Disconnect the pretensioner connector.

    7. Disconnect the connector and wire harness clamp.

    8. Operate the front seat cushion lever to move the ottoman of the front seat assembly LH to the lowermost position.

    9. B006LYP

      Remove the front seat assembly LH as shown in the illustration.

      Note


      • Protect the front seat legs.


      • Do not damage the front seat assembly LH, body exterior or interior parts.