FRONT SEAT ASSEMBLY(for Front Passenger Side Power Seat) INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. INSTALL FRONT SEAT ASSEMBLY RH


    1. B006RIG

      Place the front seat assembly RH in the vehicle, as shown in the illustration.

      Note

      Do not damage the front seat assembly RH, body exterior or interior parts.

    2. Tilt the front seat assembly RH toward the rear of the vehicle.

      Note

      Do not damage the front seat assembly RH or interior parts.

    3. Connect the connector.

    4. Connect the connector of the front seat airbag assembly RH.

    5. Align the adjuster pin of the front seat assembly RH with the hole in the body.

    6. Temporarily install the front seat assembly RH with the 4 bolts.

    7. Operate the ottoman lever to fully close the ottoman of the front seat assembly RH.

    8. Operate the power seat switch knob to slide the front seat assembly RH to the rearmost position.

    9. B006NSVN01

      Tighten the 2 bolts on the front side of the front seat assembly RH in the order shown in the illustration.

      Torque:
      39 N*m  { 398 kgf*cm, 29 ft.*lbf }

    10. Operate the power seat switch knob to slide the front seat assembly RH to the frontmost position.

    11. B006L6KN01

      Tighten the 2 bolts on the rear side of the front seat assembly RH in the order shown in the illustration.

      Torque:
      39 N*m  { 398 kgf*cm, 29 ft.*lbf }

  2. INSTALL FRONT SEAT LEG COVER


    1. B006NY2

      Operate the seat track adjusting handle to slide the front seat assembly RH to the rearmost position.

    2. Attach the guide and claw to install the front seat leg cover.

  3. INSTALL FRONT SEAT NO. 1 LEG COVER


    1. B006LENC01
      B006N8A Installation in this Direction (1)
      B006NJK Installation in this Direction (2)

      for Inner Side:


      1. Push in installation direction (1) shown in the illustration and attach the hook to install the front seat No.1 leg cover.

      2. Push the part closed in installation direction (2) shown in the illustration to attach the claw.

    2. B006NDYC01
      B006N8A Installation in this Direction (1)
      B006NJK Installation in this Direction (2)

      for Outer Side:


      1. Push in installation direction (1) shown in the illustration and attach the hook to install the front No.1 seat leg cover.

      2. Push the part closed in installation direction (2) shown in the illustration to attach the claw.

  4. INSTALL FRONT SEAT LEG COVER RH


    1. Operate the power seat switch knob RH (for Slide) to slide the front seat assembly LH to the frontmost position.

    2. B006NQNC01
      B006N8A Installation in this Direction

      Push in the installation direction shown in the illustration and align the claw and guide.

    3. B006R8YC01
      B006N8A Installation in this Direction

      Push in the installation direction shown in the illustration to attach the claw.

    4. B006MNTC01
      B006N8A Installation Direction

      Push in the installation direction shown in the illustration to attach the claw and install the front seat leg cover RH.

    5. Return the floor carpet to its original position.

  5. INSTALL NO. 3 FLOOR CARPET MOULDING


    1. Temporarily install the 2 No. 3 floor carpet mouldings.

    2. Using a screwdriver, rotate the screw portion 90° clockwise and lock it to install the 2 No. 3 floor carpet mouldings.

  6. INSTALL REAR DOOR SCUFF PLATE RH

    Click here

  7. INSTALL DOOR SCUFF PLATE ASSEMBLY RH

    Click here

  8. INSTALL COWL SIDE TRIM BOARD RH

    Click here

  9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  10. INSPECT SRS WARNING LIGHT

    Click here

  11. INSPECT SEAT BELT WARNING LIGHT

    Click here