FRONT SEAT ASSEMBLY(for Front Passenger Side Power Seat) REASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:


  • B006LWS

    Wear protective gloves. Sharp areas on the parts may injure your hands.

  • There is risk of injury.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. INSTALL SEATBACK CLIMATE CONTROL DUCT RH


    1. B006PBO

      Attach the claw and install the seatback climate control duct RH.

  2. INSTALL SEATBACK CLIMATE CONTROL BLOWER RH


    1. B006QD5

      Install the seatback climate control blower RH with the 4 screws.

  3. INSTALL FRONT SEATBACK HOOK


    1. B006O1NC03
      B006N8A Install in this Direction

      Install the 2 front seatback hooks.

  4. INSTALL FRONT SEATBACK SPRING SUB-ASSEMBLY RH


    1. B006O8RC01
      B006N8A Install in this Direction (1)
      B006NJK Install in this Direction (2)

      Push in the installation direction (1) shown in the illustration to attach the hook.

    2. Push in the installation direction (2) shown in the illustration to attach the claw and install the front seatback spring sub-assembly RH.

  5. INSTALL FRONT SEATBACK EDGE PROTECTOR


    1. B006MJCC02
      B006N8A Install in this Direction (1)
      B006NJK Install in this Direction (2)

      Attach the guide in the installation direction (1) shown in the illustration.

    2. Attach the claw in the installation direction (2) shown in the illustration and install the 2 front seatback edge protectors.

  6. INSTALL RECLINING ADJUSTER INSIDE COVER LH


    1. B006POSC03
      *a Guide A
      *b Guide B
      B006N8A Install in this Direction (1)
      B006NJK Install in this Direction (2)

      Rotate the part in the installation direction (1) shown in the illustration and attach the guide A.

    2. Push down the guide B in the installation direction (2) shown in the illustration to install the reclining adjuster inside cover LH.

  7. INSTALL RECLINING ADJUSTER INSIDE COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  8. INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY RH


    1. B006P7HC02
      *a Hook
      *b Guide
      B006N8A Install in this Direction (1)
      B006NJK Install in this Direction (2)

      Push in the installation direction (1) shown in the illustration to attach the hook.

    2. Pull in the installation direction (2) shown in the illustration to attach the guide and install the front seat cushion spring sub-assembly RH.

  9. INSTALL FRONT SEAT CUSHION BRACKET RH


    1. B006LH4

      Attach the guide.

    2. Install the front seat cushion bracket RH with the 4 screws.

  10. INSTALL SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY RH


    1. B006O53C01
      *a Hook
      *b Guide
      *c Bracket
      B006N8A Install in this Direction (1)
      B006NJK Install in this Direction (2)

      Move in the installation direction (1) shown in the illustration to attach the hook and align the guide.

    2. Close the seat cushion climate control blower assembly RH bracket in the installation direction (2) shown in the illustration.

    3. Install the seat cushion climate control blower assembly RH with the screw.

  11. INSTALL SEAT CUSHION CLIMATE CONTROL DUCT RH


    1. B006MJWC01
      B006N8A Install in this Direction

      Insert the seat cushion climate control duct RH in the installation direction shown in the illustration and align the spring with the guide.

      Note

      Do not dirty or damage the seat cushion climate control duct RH.

    2. Attach the claw and install the seat cushion climate control duct RH.

  12. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH


    1. B006O5LC01
      B006N8A Install in this Direction

      Attach the claw and hook.

    2. Install the front seat cushion edge protector LH with the screw.

  13. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH

    Tech Tips

    Use the same procedure described for the LH side.

  14. INSTALL LOWER INNER RECLINING ADJUSTER ARM SUB-ASSEMBLY RH


    1. B006KSO

      Install the lower inner reclining adjuster arm sub-assembly RH with the 4 bolts.

      Torque:
      32 N*m  { 326 kgf*cm, 24 ft.*lbf }

  15. INSTALL FRONT SEAT CUSHION HINGE COVER LH


    1. B006MGIC01
      *a Guide A
      *b Guide B
      B006N8A Install in this Direction (1)
      B006NJK Install in this Direction (2)

      Push in the installation direction (1) shown in the illustration to attach the guide A.

    2. Push in the installation direction (2) shown in the illustration to attach the guide B.

    3. Install the front seat cushion hinge cover LH with the screw.

    4. B006KNRC01
      B006N8A Install in this Direction

      Insert the guide and attach the claw and install the front seat cover.

  16. INSTALL FRONT SEAT CUSHION HINGE COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  17. INSTALL FRONT SEAT PLATE SUB-ASSEMBLY LH


    1. B006MQJC01
      B006N8A Install in this Direction

      Push in the installation direction shown in the illustration and install the front seat plate sub-assembly LH with the screw.

  18. INSTALL FRONT SEAT PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  19. INSTALL FRONT SEAT NO. 1 FOOTREST COVER


    1. B006MF3C03
      *a Clip A
      *b Clip B

      Attach the clip A and install the front seat No. 1 footrest cover.

    2. Install the 2 clips B.

  20. INSTALL FRONT SEATBACK FRAME SUB-ASSEMBLY RH


    1. B006LIQ

      Attach the guide.

    2. B006LRQ

      Install the front seatback frame sub-assembly RH with the 4 bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Tech Tips

      Tighten the bolts while pushing the front seatback frame sub-assembly RH.

      B006QYE

  21. INSTALL FRONT SEAT WIRE RH


    1. B006RGS

      Attach the clamp and claw.

    2. Connect the 3 connectors and install the front seat wire RH.

    3. B006PKK

      Attach the claw and guide.

    4. Install the connector holder with the 2 screws.

  22. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY RH


    1. B006QFP

      Attach the clamp and install the seat heater control sub-assembly RH.

    2. Connect the connector.

  23. INSTALL NO. 1 SEAT WIRE


    1. B006OFK

      Attach the clamp.

    2. Connect the 2 connectors and install the No. 1 seat wire.

  24. INSTALL FRONT NO. 3 SEAT WIRE RH


    1. B006KSB

      Attach the clamp.

    2. B006PA9

      Attach the clamp.

    3. Connect the connector and install the front No. 3 seat wire RH.

  25. INSTALL FRONT NO. 2 SEAT WIRE RH


    1. Attach the clamp.

    2. B006MW4C05
      *a Hook
      *b Clamp

      Attach the hook.

    3. Connect the 3 connectors and install the front No. 2 seat wire RH.

  26. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY RH

    Click here

  27. INSTALL SEAT COVER WIRE


    1. B006MFMN01

      Install the seat cover wire.

      Tech Tips


      • Wire 1000 mm (3.28 ft.) or longer and shaped wire are available as supplied parts.


      • When a wire that is less than 1000 mm (3.28 ft.) in length is needed, cut or shape 1000 mm (3.28 ft.) wire into the dimensions shown in the illustration.


      • Make sure to read the precautions before preparing the wire.

        Click here

      Dimensions
      A 240 mm (9.45 in.)
      B 260 mm (10.24 in.)
      C 340 mm (1.12 ft.)
      D 300 mm (11.81 in.)
      E 150 mm (5.91 in.)

      Tech Tips

      The dimensions shown in the illustration are the lengths.

      B006OSZ

  28. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

    Tech Tips


    • Refer to the precautions on wrinkles to avoid creating any on the separate type front seat cushion cover RH when installing the seat cover.

      Click here


    • As shown in the illustration, fix all of the cover seam allowances in the same direction.

    B006RE0N02

    1. Set the separate type front seat cushion cover.

    2. B006NHMC02
      *a Hog Ring Pliers
      B006PCE Fastening Tape

      Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 21 new hog rings in the order indicated in the illustration.

      Note


      • Be careful not to damage the separate type front seat cushion cover.


      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

    3. Using hog ring pliers, connect the 2 straps of the separate type front seat cushion cover to the separate type front seat cushion pad with 2 new hog rings.

      B006OOQC01
      *a Hog Ring Pliers - -

      Note

      Be careful not to damage the separate type front seat cushion cover.

  29. INSTALL SEAT CUSHION COVER WITH PAD


    1. B006R0F

      Attach the claw and install the connector of the occupant detection sensor.

    2. Attach the J hook and clip.

      B006QMM
    3. B006PCJ

      Attach the J hook and install the seat cushion cover with pad.

    4. B006LRB

      Connect the connector.

    5. B006OR7

      Attach the clamp.

    6. Connect the connector.

  30. INSTALL FRONT SEAT INNER NO. 1 CUSHION SHIELD LH


    1. B006OIVC01
      B006N8A Install in this Direction

      Attach the clip.

    2. Install the front seat inner No. 1 cushion shield LH with the screw.

  31. INSTALL FRONT SEAT INNER NO. 1 CUSHION SHIELD RH

    Tech Tips

    Use the same procedure described for the LH side.

  32. INSTALL FRONT SEAT NO. 2 FOOTREST COVER


    1. B006LKHC01
      B006N8A Install in this Direction

      Push in the installation direction shown in the illustration to install the hook and guide.

    2. B006P0PC01
      B006N8A Install in this Direction

      Push up in the installation direction shown in the illustration and install the front seat No. 2 footrest cover with the 2 screws.

    3. Attach the clamp.

    4. While sliding the part in the direction indicated by the arrow shown in the illustration, align the part with the J hook to install it.

      B006Q3V

  33. INSTALL FRONT SEAT AIRBAG ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

    Click here

  34. INSTALL SEATBACK FELT


    1. B006LN7

      Install the seatback felt.

  35. INSTALL FRONT SEATBACK HEATER ASSEMBLY RH

    Click here

  36. INSTALL SEAT COVER WIRE


    1. B006OPDN01

      Install the seat cover wire.

      Tech Tips


      • Wire 1000 mm (3.28 ft.) or longer and shaped wire are available as supplied parts.


      • When a wire that is less than 1000 mm (3.28 ft.) in length is needed, cut or shape 1000 mm (3.28 ft.) wire into the dimensions shown in the illustration.


      • Make sure to read the precautions before preparing the wire.

        Click here

      Dimensions
      A 260 mm (10.24 in.)
      B 530 mm (1.74 ft.)

      Tech Tips

      The dimensions shown in the illustration are the lengths.

      B006OSZ

  37. INSTALL SEPARATE TYPE FRONT SEATBACK COVER

    Tech Tips


    • When installing the separate type front seatback cover, refer to the precautions in order to prevent wrinkles from forming.

      Click here


    • Align the seam allowance in a single direction as shown in the illustration.

      B006OFUN05

    1. Set the separate type front seatback cover.

    2. Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 10 new hog rings in the order indicated in the illustration and attach the fastening tape.

      B006MX0C11
      *a Hog Ring Pliers - -
      B006PCE Fastening Tape - -

      Note


      • Be careful not to damage the separate type front seatback cover.


      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

  38. INSTALL SEATBACK COVER WITH PAD


    1. B006NSCC01
      B006N8A Install in this Direction (1)
      B006NJK Install in this Direction (2)

      Push in the installation direction (1) shown in the illustration to temporarily install the seatback cover with pad.

    2. Push in the rear end of the seatback cover with pad in the installation direction (2) shown in the illustration.

    3. B006ML3C02
      *a Inner Bracket
      *b Outer Bracket

      Install the 2 brackets of the separate type front seatback cover with a new nut in the order indicated in the illustration.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Note


      • Be sure to wrap the front seat airbag assembly RH with the bracket when installing.

      • Check that the band is not twisted after installing the bracket.

      • If the bracket is not securely installed, the front seat airbag assembly RH may not deploy properly. For this reason, the bracket must be securely installed.

    4. B006PHH

      Attach the clamp.

    5. Connect the connector.

    6. B006M3FC04
      B006PCE Fastening Tape

      Secure the wire harness of the front seat airbag assembly RH with fastening tape.

    7. B006M01

      Attach the J hook.

    8. B006RIB

      Install the 2 clips.

    9. B006NXBC01
      *a Hog Ring Pliers

      Using hog ring pliers, install 4 new hog rings.

  39. INSTALL SEATBACK CLIMATE CONTROL COVER RH


    1. B006RCEC01
      B006N8A Install in this Direction

      Install the seatback climate control cover RH with the 4 screws.

  40. INSTALL FRONT SEAT HEADREST SUPPORT


    1. B006MCHC01
      B006N8A Install in this Direction

      Push in the installation direction shown in the illustration and attach the claw to install the 2 front seat headrest supports.

  41. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY RH


    1. B006LRGC01
      B006N8A Install in this Direction (1)
      B006NJK Install in this Direction (2)

      Push in the installation direction (1) shown in the illustration to install the guide.

    2. Push in the installation direction (2) shown in the illustration to attach the claw and install the front seatback board sub-assembly RH.

    3. B006R4O

      Attach the band.

  42. INSTALL ASSIST GRIP


    1. Attach the guide.

    2. B006PK5

      Install the assist grip with the 2 bolts.

      Torque:
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }

  43. INSTALL ASSIST GRIP PLUG


    1. B006PN8

      Attach the claw and guide install the 2 assist grip plugs.

  44. INSTALL FRONT POWER SEAT SWITCH (w/ Shoulder Switch)

    Click here

  45. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH

    Click here

  46. INSTALL FRONT SEAT INNER CUSHION SHIELD RH


    1. B006PYIC01
      B006N8A Install in this Direction

      Push in the installation direction shown in the illustration to attach the claw.

    2. B006PXRC01
      B006N8A Install in this Direction

      Push in the installation direction shown in the illustration to attach the clip and claw.

    3. B006NR3C01
      B006N8A Install in this Direction

      Push in the installation direction shown in the illustration and attach the guide and claw.

    4. B006L1JC01
      B006N8A Install in this Direction

      Push in the installation direction shown in the illustration to attach the claw and install the front seat inner cushion shield RH.

  47. INSTALL FRONT POWER SEAT SWITCH (for Ottoman)

    Click here

  48. INSTALL FRONT POWER SEAT SWITCH RH

    Click here

  49. INSTALL FRONT SEAT CUSHION SHIELD RH


    1. B006LCW

      Attach the clamp.

    2. Connect the 2 connectors.

    3. B006P44C01
      B006N8A Install in this Direction

      Push in the installation direction shown in the illustration to attach the clip and claw.

    4. B006M4DC01
      B006N8A Install in this Direction

      Push in the installation direction shown in the illustration to install the guide.

    5. B006MA7C01
      B006N8A Install in this Direction

      Push in the installation direction shown in the illustration to attach the claw and guide.

    6. B006PZOC01
      B006N8A Install in this Direction

      Push in the installation direction shown in the illustration to attach the claw and install the front seat cushion shield RH.

  50. INSTALL POWER SEAT SWITCH KNOB RH (for Reclining)


    1. B006R6CC01
      B006N8A Install in this Direction

      Push in the installation direction shown in the illustration and attach the claw to install the power seat switch knob RH.

  51. INSTALL POWER SEAT SWITCH KNOB RH (for Slide)


    1. B006RG4C01
      B006N8A Install in this Direction

      Push in the installation direction shown in the illustration and attach the claw to install the power seat switch knob RH.

  52. INSTALL FRONT SEAT LEG COVER


    1. B006L2L

      Install the front seat leg cover.

  53. INSTALL FRONT SEAT LEG ASSEMBLY RH


    1. B006KX3

      Install the front seat leg assembly RH with the 5 nuts.

      Torque:
      19.5 N*m  { 199 kgf*cm, 14 ft.*lbf }
    2. B006MNL

      Attach the claw and clamp.

  54. INSTALL SEAT ADJUSTER COVER CAP RH

    B006QLPC01
    B006N8A Install in this Direction

    1. Push in the installation direction shown in the illustration to install the 2 seat adjuster cover caps RH.

  55. INSTALL FRONT SEAT HEADREST ASSEMBLY


    1. Install the front seat headrest assembly.