FRONT SEAT ASSEMBLY(for Front Passenger Side Power Seat) REMOVAL

CAUTION / NOTICE / HINT

Additional Work After Servicing
Replacement Part or Procedure Necessary Procedures Effects/Inoperative Functions when not Performed Link
Disconnect cable from negative (-) battery terminal Drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes) Stop and start system

Click here

Correct the steering angle neutral point Panoramic view monitor system

Click here

Servo motor initialization Air conditioning system

Click here

Reset slide door close position Power slide door system

Click here

Reset back door close position Back door opener

Click here

Initialize back door lock Initialize back door lock

Click here

CAUTION:


  • B006LWS

    Wear protective gloves. Sharp areas on the parts may injure your hands.

  • There is risk of injury.

  • If the front seat side airbag was deployed, replace the front seat airbag assembly, separate type front seatback frame sub-assembly, separate type front seatback cover and separate type front seatback pad with the necessary parts in accordance with the extent of the collision damage.

  • Replace any other damaged parts as necessary.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing.

    Click here

    B006M99

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Click here

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE COWL SIDE TRIM BOARD RH

    Click here

  4. REMOVE DOOR SCUFF PLATE ASSEMBLY RH

    Click here

  5. REMOVE REAR DOOR SCUFF PLATE RH

    Click here

  6. REMOVE NO. 3 FLOOR CARPET MOULDING


    1. B006QTJC01
      B006N8A Removal in this Direction
      B006PCE Protective Tape

      Using a screwdriver with its tip wrapped in protective tape, rotate the screw portion 90° counterclockwise to unlock it.

    2. Pull in the removal direction shown in the illustration to remove the guide and 2 No. 3 floor carpet mouldings.

  7. REMOVE FRONT SEAT LEG COVER RH


    1. B006O17C01
      B006N8A Removal in this Direction

      Operate the power seat switch knob RH (for Slide) to slide the front seat assembly RH to the frontmost position.

    2. Pull in the removal direction shown in the illustration to fold back the floor carpet.

    3. B006N0AC01
      B006Q1Z Place Hand Here
      B006N8A Removal in this Direction

      Place your hand at the positions shown in the illustration and pull in the removal direction to detach the claw

    4. B006P74C01
      B006Q1Z Place Hand Here
      B006N8A Removal in this Direction

      Place your hand at the positions shown in the illustration and pull in the removal direction to detach the claw

    5. B006KOOC01
      B006Q1Z Place Hand Here
      B006N8A Removal in this Direction

      Place your hands at the positions shown in the illustration and pull in the removal direction shown in the illustration to detach the claw and guide and remove the front seat leg cover RH.

  8. REMOVE FRONT SEAT NO. 1 LEG COVER


    1. B006PBRC01
      B006N8A Removal in this Direction (1)
      B006NJK Removal in this Direction (2)
      B006PCE Protective Tape

      for Outer Side:


      1. Using a screwdriver with its tip wrapped in protective tape, detach the claw and open the front No. 1 seat leg cover in removal direction (1) as shown in the illustration.

      2. Pull in removal direction (2) shown in the illustration to detach the hook and remove the front No. 1 seat leg cover.

    2. B006R1MC01
      B006N8A Removal in this Direction (1)
      B006NJK Removal in this Direction (2)
      B006PCE Protective Tape

      for Inner Side:


      1. Using a screwdriver with its tip wrapped in protective tape, detach the claw and open the front No. 1 seat leg cover in removal direction (1) as shown in the illustration.

      2. Pull in removal direction (2) shown in the illustration to detach the hook and remove the front No. 1 seat leg cover.

  9. REMOVE FRONT SEAT LEG COVER


    1. B006NMBC01
      B006N8A Removal in this Direction

      Detach the claw and guide and remove the front seat leg cover.

  10. REMOVE FRONT SEAT ASSEMBLY RH


    1. B006L6K

      Remove the 2 bolts on the rear side of the front seat assembly RH.

    2. Operate the power seat switch knob RH (for Slide) to slide the front seat assembly RH to the rearmost position.

    3. B006NSV

      Remove the 2 bolts on the front side of the front seat assembly RH.

    4. Operate the power seat switch knob RH (for Slide) to slide the front seat assembly RH to the center position.

    5. Operate the power seat switch knob RH (for Reclining) to set the seatback of the front seat assembly RH to the perpendicular position.

    6. Operate the ottoman lever to fully open the ottoman of the front seat assembly RH.

    7. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      B006LHC

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here

    8. Disconnect the front seat airbag assembly RH connector.


      1. Push the slider to detach the primary lock. Continue pushing and slide the slider to detach the secondary lock and then disconnect the airbag connector.

        B006PX0C03
        *1 Slider - -
        *a Push *b Slide

    9. Disconnect the connector.

    10. B006MG9

      Remove the front seat assembly RH as shown in the illustration.

      Note


      • Protect the front seat legs.


      • Do not damage the front seat assembly RH, body exterior or interior parts.