FRONT SEAT ASSEMBLY(for Driver Side Power Seat) REMOVAL

CAUTION / NOTICE / HINT

Additional Work After Servicing
Replacement Part or Procedure Necessary Procedures Effects/Inoperative Functions when not Performed Link
Disconnect cable from negative (-) battery terminal Drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes) Stop and start system

Click here

Correct the steering angle neutral point Panoramic view monitor system

Click here

Servo motor initialization Air conditioning system

Click here

Reset slide door close position Power slide door system

Click here

Reset back door close position Back door opener

Click here

Initialize back door lock Initialize back door lock

Click here

CAUTION:


  • B006LWS

    Wear protective gloves. Sharp areas on the parts may injure your hands.

  • There is risk of injury.

  • If the front seat side airbag was deployed, replace the front seat airbag assembly, separate type front seatback frame sub-assembly, separate type front seatback cover and separate type front seatback pad with the necessary parts in accordance with the extent of the collision damage.

  • Replace any other damaged parts as necessary.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing.

    B006M99

    Click here

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Click here

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE COWL SIDE TRIM BOARD LH

    Click here

  4. REMOVE DOOR SCUFF PLATE ASSEMBLY LH

    Click here

  5. REMOVE REAR DOOR SCUFF PLATE LH

    Click here

  6. REMOVE NO. 3 FLOOR CARPET MOULDING


    1. B006OH9C01
      B006N8A Removal in this Direction
      B006PCE Protective Tape

      Using a screwdriver with its tip wrapped in protective tape, rotate the screw portion 90° counterclockwise to unlock it.

    2. Pull in the removal direction shown in the illustration to remove the guide and 2 No. 3 floor carpet mouldings.

  7. REMOVE FRONT SEAT LEG COVER LH


    1. Operate the power seat switch knob LH (for Slide) to slide the front seat assembly LH to the frontmost position.

    2. B006M0IC01
      B006N8A Removal in this Direction

      Pull in the removal direction shown in the illustration to fold back the floor carpet.

    3. B006KUHC01
      B006Q1Z Place Hand Here
      B006N8A Removal in this Direction

      Place your hand at the positions shown in the illustration and pull in the removal direction to detach the claw

    4. B006N7FC02
      B006Q1Z Place Hand Here
      B006N8A Removal in this Direction

      Place your hand at the positions shown in the illustration and pull in the removal direction to detach the claw

    5. B006L6HC02
      B006Q1Z Place Hand Here
      B006N8A Removal in this Direction

      Place your hand at the positions shown in the illustration and pull in the removal direction shown in the illustration to detach the claw and guide and remove the front seat leg cover LH.

  8. REMOVE FRONT SEAT NO. 1 LEG COVER


    1. for Outer Side:


      1. B006MBRC01
        B006N8A Removal in this Direction (1)
        B006NJK Removal in this Direction (2)

        Using a screwdriver with its tip wrapped in protective tape, detach the claw and open the front seat No. 1 leg cover in removal direction (1) as shown in the illustration.

      2. Pull in removal direction (2) shown in the illustration to detach the hook and remove the front seat No. 1 leg cover.

    2. for Inner Side:


      1. B006LT7C01
        B006N8A Removal in this Direction (1)
        B006NJK Removal in this Direction (2)

        Using a screwdriver with its tip wrapped in protective tape, detach the claw and open the front seat No. 1 leg cover in removal direction (1) as shown in the illustration.

      2. Pull in removal direction (2) shown in the illustration to detach the hook and remove the front seat No. 1 leg cover.

  9. REMOVE FRONT SEAT ASSEMBLY LH


    1. B006LQV

      Remove the 2 bolts on the rear side of the front seat assembly LH.

    2. Operate the power seat switch knob LH (for Slide) to slide the front seat assembly LH to the rearmost position.

    3. B006OAG

      Remove the 2 bolts on the front side of the front seat assembly RH.

    4. Operate the power seat switch knob LH (for Slide) to slide the front seat assembly LH to the frontmost position.

    5. Operate the power seat switch knob LH (for Vertical) to set the seat cushion height of the front seat assembly LH to the uppermost position.

    6. Operate the power seat switch knob LH (for Reclining) to set the seatback of the front seat assembly LH to the perpendicular position.

    7. B006LHC

      Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here

    8. Disconnect the front seat airbag assembly LH connector.


      1. Push the slider to detach the primary lock. Continue pushing and slide the slider to detach the secondary lock and then disconnect the airbag connector.

        B006PX0C12
        *1 Slider - -
        *a Push *b Slide

    9. Disconnect the connector.

    10. B006RHG

      Remove the front seat assembly LH as shown in the illustration.

      Note


      • Protect the front seat legs.


      • Do not damage the front seat assembly LH, body exterior or interior parts.