FRONT SEAT ASSEMBLY(for Manual Seat) INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.
If the front seat side airbag was deployed, replace the front seat airbag assembly, separate type front seatback frame sub-assembly, separate type front seatback cover and separate type front seatback pad with the necessary parts in accordance with the extent of the collision damage.
Replace any other damaged parts as necessary.

PROCEDURE

INSTALL FRONT SEAT ASSEMBLY RH
1. Place the front seat assembly RH in the vehicle, as shown in the illustration.
  
  Note
  
  Do not damage the front seat assembly RH, body exterior or interior parts.
2. Tilt the front seat assembly RH toward the rear of the vehicle.
  
  Note
  
  Do not damage the front seat assembly RH or interior parts.
3. Connect the connector.
4. Connect the connector of the front seat airbag assembly RH.
5. Align the adjuster pin of the front seat assembly RH with the hole in the body.
6. Temporarily install the front seat assembly RH with the 4 bolts.
7. Operate the seat track adjusting handle to slide the front seat assembly RH to the rearmost position.
8. Tighten the 2 bolts on the front side of the front seat assembly RH in the order shown in the illustration.
  
  Torque:
  
  39 N*m { 398 kgf*cm, 29 ft.*lbf }
9. Operate the seat track adjusting handle to slide the front seat assembly RH to the frontmost position.
10. Tighten the 2 bolts on the rear side of the front seat assembly RH in the order shown in the illustration.
  
  Torque:
  
  39 N*m { 398 kgf*cm, 29 ft.*lbf }
INSTALL FRONT SEAT LEG COVER
1. Operate the seat track adjusting handle to slide the front seat assembly RH to the rearmost position.
2. Attach the guide and claw to install the front seat leg cover.

INSTALL FRONT SEAT NO. 1 LEG COVER

	Installation in this Direction (1)
	Installation in this Direction (2)

Inner Side:

Push in installation direction (1) shown in the illustration and attach the hook to install the front No.1 seat leg cover.
Push the part closed in installation direction (2) shown in the illustration to attach the claw.

	Installation in this Direction (1)
	Installation in this Direction (2)

Outer Side:

Push in installation direction (1) shown in the illustration and attach the hook to install the front No.1 seat leg cover.
Push the part closed in installation direction (2) shown in the illustration to attach the claw.

INSTALL RH SEAT FRONT SEAT LEG COVER
1. Operate the seat track adjusting handle to slide the front seat assembly RH to the frontmost position.
2. Installation in this Direction
  
  Push in the installation direction shown in the illustration and align the claw and guide.
3. Installation in this Direction
  
  Push in the installation direction shown in the illustration to attach the claw.
4. Installation in this Direction
  
  Push in the installation direction shown in the illustration to attach the claw and install the front seat leg cover.
5. Return the floor carpet to its original position.
INSTALL NO. 3 MOULDING FLOOR CARPET
1. Temporarily install the 2 No. 3 floor carpet mouldings.
2. Using a screwdriver, rotate the screw portion 90° clockwise and lock it to install the 2 No. 3 floor carpet mouldings.
INSTALL REAR DOOR SCUFF PLATE RH

Click here
INSTALL DOOR SCUFF PLATE ASSEMBLY RH

Click here
INSTALL COWL SIDE TRIM BOARD RH

Click here
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here
INSPECT SRS WARNING LIGHT

Click here
INSPECT SEAT BELT WARNING LIGHT

Click here