FRONT SEAT ASSEMBLY(for Manual Seat) REASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:


  • B006LWS

    Wear protective gloves. Sharp areas on the parts may injure your hands.

  • There is risk of injury.

  • If the front seat side airbag was deployed, replace the front seat airbag assembly, separate type front seatback frame sub-assembly, separate type front seatback cover and separate type front seatback pad with the necessary parts in accordance with the extent of the collision damage.

  • Replace any other damaged parts as necessary.

PROCEDURE


  1. INSTALL SEAT TRACK ADJUSTING HANDLE


    1. Push in the installation direction shown in the illustration to attach the lock pins and install the seat track adjusting handle.

      B006LU7C01
      *1 Lock Pin - -
      B006N8A Install in this Direction - -

  2. INSTALL FRONT SEATBACK SRRING SUB-ASSEMBLY RH


    1. B006OH3C01
      B006N8A Install in this Direction

      Push in the installation direction shown in the illustration to install the front seatback spring sub-assembly RH to the hook.

  3. INSTALL FRONT SEATBACK HOOK


    1. B006PJGC01
      B006N8A Install in this Direction

      Push the 2 front seatback hooks in the installation direction shown in the illustration.

    2. B006N86

      Attach the clamps to install the 2 front seatback hooks.

  4. INSTALL FRONT SEATBACK EDGE PROTECTOR


    1. B006QFO

      Attach the claw and guide to install the front seatback edge protector.

  5. INSTALL RECLINING ADJUSTER INSIDE COVER RH


    1. B006ODIC01
      B006N8A Install in this Direction (1)
      B006NJK Install in this Direction (2)

      Rotate the part in installation direction (1) shown in the illustration and align the guide.

    2. Push down the guide in installation direction (2) shown in the illustration to install the reclining adjuster inside cover RH.

  6. INSTALL RECLINING ADJUSTER INSIDE COVER LH

    Tech Tips

    Use the same procedure as for the RH side.

  7. INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY RH


    1. B006NO0C01
      B006N8A Install in this Direction (1)
      B006NJK Install in this Direction (2)

      While rotating the part in installation direction (1) shown in the illustration, install the hook.

    2. Pull in installation direction (2) shown in the illustration to install the front seat cushion spring sub-assembly RH to the hook.

  8. INSTALL FRONT SEATBACK FRAME SUB-ASSEMBLY RH


    1. B006Q6WC01
      B006N8A Install in this Direction

      Push in the installation direction and align the guide.

    2. B006LQX

      Install the front seatback frame sub-assembly RH with the 4 bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  9. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH


    1. B006Q69C01
      B006N8A Install in this Direction (1)
      B006NJK Install in this Direction (2)

      Push in installation direction (1) shown in the illustration to install the guide.

    2. Pull in installation direction (2) shown in the illustration, attach the claw.

    3. Install the front seat cushion edge protector RH with the screw.

  10. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH

    Tech Tips

    Use the same procedure as for the RH side.

  11. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH


    1. B006O57C01
      B006N8A Install in this Direction

      Push in the installation direction shown in the illustration to attach the clip.

    2. B006OBLC01
      B006N8A Install in this Direction

      Push the guide in the installation direction shown in the illustration.

    3. Install the front seat lower cushion shield RH with the screw.

  12. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH

    Tech Tips

    Use the same procedure as for the RH side.

  13. INSTALL SEAT COVER WIRE


    1. B006NDKN01

      Install the seat cover wire.

      Tech Tips


      • There are service parts available for wires of 1000 mm or longer and formed wires.


      • When a wire that is less than 1000 mm (3.28 ft.) in length is needed, cut and shape a 1000 mm supplied wire into the dimensions shown in the illustration.


      • Refer to the precautions when creating a wire.

        Click here

      Lentch
      A 150 mm (5.91 in.)
      B 120 mm (4.72 in.)
      C 240 mm (9.45 in.)
      D 270 mm (10.63 in.)
      E 300 mm (11.81 in.)

      Tech Tips

      The dimensions shown in the illustration are the length.

      B006OSZ

  14. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

    Tech Tips


    • Refer to the precautions on wrinkles to avoid creating any on the separate type front seat cushion cover when installing the seat cover.

      Click here


    • As shown in the illustration, fix all of the cover seam allowances in the same direction.

      B006KTEE01

    1. Temporarily install the separate type front seat cushion cover to the separate type front seat cushion pad.

    2. Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 18 new hog rings in the order shown in the illustration.

      B006L97C04
      *1 Hog Ring Pliers - -
      *a Cutout - -

    3. Using hog ring pliers, connect the 2 straps of the separate type front seat cushion cover to the separate type front seat cushion pad with 2 new hog rings.

      Tech Tips


      • Do not dirty or damage the separate type front seatback cover.


      • Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seatback pad.

      B006NQXC01
      *1 Hog Ring Pliers - -

  15. INSTALL SEAT CUSHION COVER WITH PAD


    1. A01IFTK

      While sliding the part in the direction indicated by the arrow shown in the illustration, align the J hook to install the separate type front seat cushion cover with pad.

  16. INSTALL FRONT SEAT AIRBAG ASSEMBLY RH

    Click here

  17. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH

    Click here

  18. INSTALL SEATBACK FELT


    1. Install the seatback felt.

  19. INSTALL SEAT COVER WIRE


    1. B006OPDN01

      Install the seat cover wire.

      Tech Tips


      • There are service parts available for wires of 1000 mm or longer and formed wires.


      • When a wire that is less than 1000 mm (3.28 ft.) in length is needed, cut and shape a 1000 mm supplied wire into the dimensions shown in the illustration.


      • Refer to the precautions when creating a wire.

        Click here

      A 260 mm (10.24 in.)
      B 530 mm (1.74 ft.)

      Tech Tips

      The dimensions shown in the illustration are the length.

      B006OSZ

  20. INSTALL SEPARATE TYPE FRONT SEATBACK COVER

    Tech Tips


    • Refer to the precautions on wrinkles to avoid creating any on the separate type front seatback cover when installing the seat cover.

      Click here


    • As shown in the illustration, fix all of the cover seam allowances in the same direction.

      B006Q23N01

    1. Set the separate type front seatback cover.

    2. Using hog ring pliers, install the separate type front seatback cover with 10 new hog rings in the order shown in the illustration.

      Tech Tips


      • Do not dirty or damage the separate type front seatback cover.


      • Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seatback pad.

      B006MX0C03
      *1 Hog Ring Pliers *2 Fastening Tape
      *a Cutout - -

  21. INSTALL SEATBACK COVER WITH PAD


    1. B006NSCC01
      B006N8A Install in this Direction (1)
      B006NJK Install in this Direction (2)

      Push in installation direction (1) shown in the illustration to temporarily install the seatback cover with pad.

    2. Push in the rear end of the seatback cover with pad in installation direction (2) shown in the illustration.

    3. B006ML3

      Install the bracket of the separate type front seatback cover RH with the nut.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
    4. B006ODNC01
      B006PCE Fastening Tape

      Secure the wire harness of the front seat airbag assembly RH with fastening tape.

  22. INSTALL FRONT SEAT HEADREST SUPPORT


    1. B006MCHC01
      B006N8A Install in this Direction

      Push in the installation direction shown in the illustration and attach the claw to install the 2 front seat headrest supports.

    2. B006KYF

      Close the fastener.

    3. Install 3 new hog rings.

      B006LXDC04
      *1 Hog Ring Pliers - -
      *a Cutout - -
    4. B006QDZ

      Install the band in the position shown in the illustration.

  23. INSTALL FRONT SEATBACK HOOK


    1. A01IGIU

      Attach the claw to install the front seatback hook.

  24. INSTALL FRONT SEAT INNNER CUSHION SHIELD RH


    1. B006O8HC02
      B006N8A Install in this Direction

      Push in the installation direction shown in the illustration to attach the claw and guide.

    2. B006L1JC01
      B006N8A Install in this Direction

      Push in the installation direction shown in the illustration and attach the claw.

    3. B006LKCC01
      B006N8A Install in this Direction

      Push in the installation direction shown in the illustration and attach the claw and clip to install the front seat cushion inner shield RH.

  25. INSTALL FRONT SEAT CUSHION SHIELD RH


    1. B006RLHC01
      B006N8A Install in this Direction (1)
      B006NJK Install in this Direction (2)

      Push in installation direction (1) shown in the illustration to align the guide.

    2. Push in installation direction (2) shown in the illustration to attach the guide and claw.

    3. B006M77C01
      B006N8A Install in this Direction

      Push in the installation direction shown in the illustration to attach the claw.

    4. Install the front seat cushion shield RH with the screw.

  26. INSTALL FRONT SEAT CUSHION PROTECTOR


    1. B006PYP

      Install a new front seat cushion protector.

  27. INSTALL VERTICAL ADJUSTING HANDLE RH


    1. B006L5PC01
      B006N8A Install in this Direction

      With the seatback adjuster lever pulled up, push in the installation direction shown in the illustration to align the guide.

    2. B006P9O

      Install the vertical adjuster handle RH with the screw.

  28. INSTALL RECLINING ADJUSTER RELEASE HANDLE RH


    1. B006KN8C01
      B006N8A Install in this Direction

      Push in the installation direction shown in the illustration and attach the claw to install the reclining adjuster release handle RH.

  29. INSTALL FRONT SEAT LEG COVER


    1. B006Q78C01
      B006N8A Install in this Direction

      Push in the installation direction shown in the illustration to install the front seat leg cover.

  30. INSTALL FRONT SEAT LEG ASSEMBLY RH


    1. B006OS8

      Install the front seat leg assembly RH with the 5 nuts.

      Torque:
      19.5 N*m  { 199 kgf*cm, 14 ft.*lbf }
    2. B006Q9NC01
      *1 Wire Harness Clamp
      *2 Connector Clamp

      Attach the wire harness clamp and connector clamp.

  31. INSTALL SEAT ADJUSTER COVER CAP RH


    1. B006KNPC01
      B006N8A Install in this Direction

      Push in the installation direction shown in the illustration to install the 2 seat adjuster cover caps RH.

  32. INSTALL FRONT SEAT INNER ARMREST ASSEMBLY RH


    1. B006KTQ

      Install the front seat inner armrest assembly RH with the bolt.

      Torque:
      19 N*m  { 194 kgf*cm, 14 ft.*lbf }

  33. INSTALL NO. 1 SEAT ARMREST CAP


    1. A01IGCQ

      Attach the claw and install the No. 1 seat armrest cap.

  34. INSTALL FRONT SEAT HEADREST ASSEMBLY


    1. Install the front seat headrest assembly.