FRONT SEAT ASSEMBLY(for Manual Seat) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are installed, removed or replaced during the front seat assembly removal/installation are shown below.

Necessary procedure after parts removed/installed/replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative Functions when not Performed Link
Disconnect cable from negative (-) battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and Start System (for 2AR-FE)

Click here

Stop and Start System (for 2GR-FKS)

Click here

Memorize steering angle neutral point Panoramic View Monitor System

Click here

Initialize back door lock Power Door Lock Control System

Click here

Initialize servo motor Air Conditioning System

Click here

Reset slide door close position Power Slide Door System

Click here

Reset back door close position Power Back Door System

Click here

CAUTION:


  • B006LWS

    Wear protective gloves. Sharp areas on the parts may injure your hands.

  • There is risk of injury.

  • If the front seat side airbag was deployed, replace the front seat airbag assembly, separate type front seatback frame sub-assembly, separate type front seatback cover and separate type front seatback pad with the necessary parts in accordance with the extent of the collision damage.

  • Replace any other damaged parts as necessary.

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the RH side.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing.

    B006M99

    Click here

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    • If the airbag deploys for any reason, it may cause a serious accident.

    B006LHC

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE COWL SIDE TRIM BOARD RH

    Click here

  4. REMOVE DOOR SCUFF PLATE ASSEMBLY RH

    Click here

  5. REMOVE REAR DOOR SCUFF PLATE RH

    Click here

  6. REMOVE NO. 3 FLOOR CARPET MOULDING


    1. B006QTJC01
      B006N8A Removal in this Direction
      B006PCE Protective Tape

      Using a screwdriver with its tip wrapped in protective tape, rotate the screw portion 90° counterclockwise to unlock it.

    2. Pull in the removal direction shown in the illustration to remove the guide and 2 No. 3 floor carpet mouldings.

  7. REMOVE FRONT SEAT LEG COVER


    1. Operate the seat track adjusting handle to slide the front seat assembly RH to the frontmost position.

    2. B006O17C01
      B006N8A Removal in this Direction

      Pull in the removal direction shown in the illustration to fold back the floor carpet.

    3. B006N0AC01
      B006Q1Z Place Hand Here
      B006N8A Removal in this Direction

      Place your hand at the positions shown in the illustration and pull in the removal direction to detach the claw

    4. B006P74C01
      B006Q1Z Place Hand Here
      B006N8A Removal Direction

      Place your hand at the positions shown in the illustration and pull in the removal direction to detach the claw

    5. B006KOOC01
      B006Q1Z Place Hand Here
      B006N8A Removal Direction

      Place your hand at the positions shown in the illustration and pull in the removal direction shown in the illustration to detach the claw and guide and remove the front seat leg cover.

  8. REMOVE FRONT SEAT NO. 1 SEAT LEG COVER


    1. B006PBRC01
      B006N8A Removal in this Direction (1)
      B006NJK Removal in this Direction (2)
      B006PCE Productive Tape

      Outer Side:


      1. Using a screwdriver with its tip wrapped in protective tape, detach the claw and open the front No. 1 seat leg cover in removal direction (1) as shown in the illustration.

      2. Pull in removal direction (2) shown in the illustration to detach the hook and remove the front No. 1 seat leg cover.

    2. B006R1MC01
      B006N8A Removal in this Direction (1)
      B006NJK Removal in this Direction (2)
      B006PCE Productive Tape

      Inner Side:


      1. Using a screwdriver with its tip wrapped in protective tape, detach the claw and open the front No. 1 seat leg cover in removal direction (1) as shown in the illustration.

      2. Pull in removal direction (2) shown in the illustration to detach the hook and remove the front No. 1 seat leg cover.

  9. REMOVE FRONT SEAT LEG COVER


    1. B006NMBC01
      B006N8A Removal in this Direction

      Detach the claw and guide and remove the front seat leg cover.

  10. REMOVE FRONT SEAT ASSEMBLY RH


    1. B006L6K

      Remove the 2 bolts on the rear side of the front seat assembly RH.

    2. Operate the seat track adjusting handle to slide the front seat assembly RH to the rearmost position.

    3. B006KI8

      Remove the 2 bolts on the front side of the front seat assembly RH.

    4. Operate the seat track adjusting handle to slide the front seat assembly RH to the center position.

    5. w/ Vertical


      1. Operate the vertical adjuster handle RH to set the seat cushion height of the front seat assembly RH to the uppermost position.

    6. Operate the reclining adjuster release handle RH to set the seatback of the front seat assembly RH to the perpendicular position.

    7. Disconnect the front seat airbag assembly RH connector.


      1. Push the slider to detach the primary lock. Continue pushing and slide the slider to detach the secondary lock and then disconnect the airbag connector.

        B006PX0C03
        *1 Slider - -
        *a Push *b Slide

    8. Disconnect the connector.

    9. B006KV5

      Remove the front seat assembly RH as shown in the illustration.

      Note


      • Protect the front seat legs.


      • Do not damage the front seat assembly RH, body exterior or interior parts.