SIDE AIRBAG SENSOR(for Front Door) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are installed, removed or replaced during the door side airbag sensor removal/installation are shown below.

Necessary procedure after parts removed/installed/replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative Functions when not Performed Link
Disconnect cable from negative (-) battery terminal Drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes) Stop and start system

Click here

Correct the steering angle neutral point Panoramic view monitor system

Click here

Servo motor initialization Air conditioning system

Click here

Reset slide door close position Power slide door system

Click here

Reset back door close position Back door opener

Click here

Initialize back door lock Power door lock control system

Click here

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing.

    B006M99

    Click here

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    • If the airbag deploys for any reason, it may cause a serious accident.

    B006LHC

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE LOWER DOOR FRAME GARNISH LH

    Click here

  4. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG LH

    Click here

  5. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL

    Click here

  6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

    Click here

  7. REMOVE FRONT ARMREST ASSEMBLY LH

    Click here

  8. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

    Click here

  9. REMOVE DOOR SIDE AIRBAG SENSOR LH


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:


      • B006LHC

        Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      • B006P0Z

        If this procedure is performed without disconnecting the negative (-) terminal of the battery, the airbag may deploy even if an impact is applied only to the door side airbag sensor LH. Therefore, make sure that the negative (-) terminal of the battery is disconnected before performing this procedure.

    3. Disconnect the airbag connector.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.


      1. Push down the housing lock and slide the CPA. (At this time, the airbag connector cannot be disconnected yet.)

      2. Push down the housing lock again and disconnect the airbag connector.

        Note

        Do not push down the upper part of the CPA shown in the illustration when disconnecting the airbag connector.

        B006NUOC32
        *a Housing Lock *b CPA
        *c CPA Upper Part - -
    4. B006LRL

      Remove the bolt.

      Note


      • Loosen the bolt while holding the door side airbag sensor LH because the door side airbag sensor LH guide is easily damaged.

      • If the door side airbag sensor LH has been dropped, replace it with a new one.

    5. Detach the guide and remove the door side airbag sensor LH.

  10. REMOVE CLIP


    1. B006PI8

      Remove the clip.