FRONT SEAT SIDE AIRBAG ASSEMBLY(for Power Seat) INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:


  • B006LWS

    Wear protective gloves. Sharp areas on the parts may injure your hands.

  • There is risk of injury.

  • If the front seat side airbag was deployed, replace the front seat airbag assembly, separate type front seatback frame sub-assembly, separate type front seatback cover and separate type front seatback pad with the necessary parts in accordance with the extent of the collision damage.

  • Replace any other damaged parts as necessary.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL FRONT SEAT AIRBAG ASSEMBLY LH


    1. Install the front seat airbag assembly LH with 2 new nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Note


      • The nuts must not be reused.

      • Make sure that the separate type front seatback frame sub-assembly is not deformed. If it is, replace it with a new one.

    2. B006LLTC01
      B006PCE Fastener

      Attach the wire harness clamp and fastener.

    3. B006P1NC01
      *a Housing Lock
      *b CPA
      *c CPA Upper Part
      B006N8A Connect in this Direction

      Attach the claw to connect the airbag connector.

    4. Attach the 3 wire harness clamps.

    5. Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.

      B006Q9AC01
      *a Correct *b Incorrect
      *c CPA - -

    6. While holding the CPA be sure to engage the connectors until they are locked and check that the CPA is in its original position (when locking, make sure that a click sound can be heard).

      Note


      • Be careful not to damage the side airbag connector or wire harness.


      • When connecting the connector, make sure to push it straight in.


      • Do not hold any parts other than the yellow CPA when connecting the connector.


      • If the upper portion of the yellow CPA is held when connecting the connector, the partial connection prevention mechanism will not function due to deformation of the yellow CPA. Therefore, hold the sides of the yellow CPA.

  2. INSTALL SEATBACK FELT

    Click here

  3. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD

    Click here

  4. INSTALL FRONT SEAT HEADREST SUPPORT

    Click here

  5. INSTALL FRONT POWER SEAT SWITCH RH (w/ Shoulder Switch)

    Click here

  6. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH

    Click here

  7. INSTALL ASSIST GRIP

    Click here

  8. INSTALL ASSIST GRIP PLUG

    Click here

  9. INSTALL FRONT SEAT INNER CUSHION SHIELD LH

    Click here

  10. INSTALL FRONT SEAT CUSHION SHIELD LH

    Click here

  11. INSTALL FRONT SEAT INNER CUSHION SHIELD RH (for Front Passenger Side)

    Click here

  12. INSTALL FRONT SEAT CUSHION SHIELD RH (for Front Passenger Side)

    Click here

  13. INSTALL FRONT SEAT INNER NO. 1 CUSHION SHIELD LH (for Driver Side)

    Click here

  14. INSTALL FRONT SEAT INNER LEG COVER

    Click here

  15. INSTALL FRONT SEAT LEG ASSEMBLY LH

    Click here

  16. INSTALL FRONT SEAT ASSEMBLY

    for LH Side:

    Click here

    for RH Side:

    Click here

  17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  18. PERFORM DIAGNOSTIC SYSTEM CHECK

    Click here

  19. CHECK SRS WARNING LIGHT

    Click here