SPIRAL CABLE INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. INSTALL STEERING SENSOR

    Click here

  2. INSTALL SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

    Note


    • Do not replace the spiral with sensor cable sub-assembly with the battery connected and the engine switch on (IG).

    • Do not rotate the spiral with sensor cable sub-assembly with the battery connected and the engine switch on (IG).


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:


      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

      B006LHC

    3. Check that the front wheels are facing straight ahead.

    4. Attach the claw to install the spiral with sensor cable sub-assembly.

      Note

      When replacing the spiral with sensor cable sub-assembly with a new one, remove the lock pin before installing the steering wheel assembly.

    5. Connect each connector.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.

    6. B006PSPC01
      *a Slider
      *b Lock Position

      Connect the airbag connector and check that the slider is in the lock position.

      Tech Tips

      If the slider is not in the lock position, the airbag connector is not completely connected. Disconnect the airbag connector, check the airbag connector and spiral with sensor cable sub-assembly terminals and connector housings for deformation or foreign matter, and then reconnect the airbag connector.

  3. INSTALL UPPER STEERING COLUMN COVER

    Click here

  4. INSTALL LOWER STEERING COLUMN COVER

    Click here

  5. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

  6. ADJUST SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

    Note

    Do not adjust the spiral with sensor cable sub-assembly with the battery connected and the engine switch on (IG).


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:


      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

      B006LHC
    3. B006P3NC01
      *a Check Window
      *b Matchmark
      B006N7C Colored Roller

      Check the check window shown in the illustration.

      With the steering wheel straight ahead, align the matchmarks to check the U-turn point of the cable from the check window.

      Note

      When the following conditions cannot be checked via the check window with the front wheels facing straight ahead, there may be a malfunction in the spiral with sensor cable sub-assembly. In this case, replace the spiral with cable sensor sub-assembly with a new one.

    4. If the spiral with sensor cable sub-assembly is not centered, center it.


      1. B006P4CC01
        B006REL Interlock
        B006N8A Counterclockwise

        While pushing on the interlock indicated in the illustration, rotate the spiral with sensor cable sub-assembly counterclockwise slowly by hand until it stops.

        Note


        • When rotating the spiral with sensor cable sub-assembly, make sure to push on the interlock indicated in the illustration to release the interlock mechanism.

        • Do not turn the spiral with sensor cable sub-assembly using the airbag wire harness.

      2. B006OZDC01
        *a Check Window
        *b Matchmark
        B006N7C Colored Roller
        B006REL Interlock

        While pushing on the interlock indicated in the illustration, rotate the spiral with sensor cable sub-assembly 2.5 times clockwise from the lock position.

        Tech Tips

        The spiral with sensor cable sub-assembly will rotate approximately 2.5 turns to both the left and right from the center.

      3. Check the check window shown in the illustration.

        With the steering wheel straight ahead, align the matchmarks to check the colored roller from the check window.

        If the cable cannot be centered, it is possible that the spiral with sensor cable sub-assembly is broken. Replace the spiral with sensor cable sub-assembly with a new one.

  7. INSTALL STEERING WHEEL ASSEMBLY

    Click here

  8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  9. PERFORM DIAGNOSTIC SYSTEM CHECK

    Click here

  10. CHECK SRS WARNING LIGHT

    Click here