SMART ENTRY AND START SYSTEM(for Entry Function) CUSTOMIZE PARAMETERS

CUSTOMIZE SMART ENTRY AND START SYSTEM (for Entry Function)

1. Customizing with the GTS

   
   

   1. Connect the GTS to the DLC3.

   2. Turn the engine switch on (IG).

   3. Turn the GTS on.

   4. Enter the following menus: Customize Setting / Wireless Door Lock, Entry & Start or Warning.

   5. Select the setting by referring to the table below.

      
      Wireless Door Lock

      Tester Display	Description	Default	Setting	ECU
      Wireless Control	Function that turns the wireless door lock control system on or off	ON	0:OFF,1:ON	Main body ECU (Multiplex network body ECU)
      Hazard Answer Back	When the doors are locked by the entry lock function, the hazard warning lights flash once. When the doors are unlocked by the entry lock function, the hazard warning lights flash twice.	ON	0:OFF,1:ON	Main body ECU (Multiplex network body ECU)
      Open Door Warning	The buzzer sounds when the lock sensor on the door outside handle assembly is touched to perform entry lock with a door open.*1	ON	0:OFF,1:ON	Main body ECU (Multiplex network body ECU)
      Auto Lock Time	Function that regulates the interval between unlocking and automatic relocking of doors.	30 s	00:30 s,01:60 s,10:120 s	Main body ECU (Multiplex network body ECU)
      Wireless Buzzer Resp	Wireless buzzer response.*2	ON	0:OFF,1:ON	Main body ECU (Multiplex network body ECU)
      Wireless Buzzer Vol	Buzzer answer-back volume.*2	Level5	0000:Level7,0001:Level6,0010:Level5,0011:Level4,0100:Level3,0101:Level2,0110:Level1,0111:Level0	Main body ECU (Multiplex network body ECU)

      
      

      • *1: w/ Door Ajar Warning Buzzer Function

      • *2: w/ Wireless Door Lock Buzzer Answer-back Function

      
      Warning

      Tester Display	Description	Default	Setting	ECU
      Key Low Battery Warning	Enables or disables the sounding of the buzzer when the transmitter battery is low and the engine switch is turned off after being on (IG) for 20 minutes or more.	ON	0:OFF,1:ON	Certification ECU (Smart key ECU assembly)

      
      Entry & Start

      Tester Display	Description	Default	Setting	ECU
      Park Wait Time	Function that sets the period of time (lock confirmation time) that the door is prevented from being unlocked by operating the front door outside handle assembly after an entry lock operation is performed.	2.5s	00:0.5s,01:1.5s,10:2.5s,11:5s	Certification ECU (Smart key ECU assembly)
      Ignition Available Area	Function that sets the area that the key must be in before the engine switch can be operated.	Front or All*	00:Front,01:All	Certification ECU (Smart key ECU assembly)
      Back Door Opening Operation	Function that sets the back door when the user is carrying the electrical key transmitter sub-assembly and presses the back door opener switch assembly (open switch).	Long	00:Long,01:Twice,10:OFF	Certification ECU (Smart key ECU assembly)
      Auto Entry Cancel SW	Function that enables or disables the smart entry and start system.	OFF	0:OFF,1:ON	Certification ECU (Smart key ECU assembly)
      Touch Activation Over Threshold	The function that limits the consecutive entry lock operation to only 2 times can be changed between Active and Not Active. When in Not Active mode, there is no limit for the number of times that the consecutive entry lock operation can be performed.	Active or Not Active*	0:Active,1:Not Active	Certification ECU (Smart key ECU assembly)
      Engine Start Indicator	Function that turns the smart key indicator on the combination meter assembly on or off.	ON	0:OFF,1:ON	Certification ECU (Smart key ECU assembly)

      
      

      • *: Default setting differs depending on the country.

2. Customizing with the multi-display

   
   

   1. Turn the engine switch on (IG).

   2. Enter the following menus: SETUP / Vehicle / Vehicle customization / Door lock settings.

   3. Select the setting by referring to the table below.

      Display	Default	Content	Setting	Relevant ECU
      Smart entry and start system	On	Function that enables or disables the smart entry and start system.	On or Off	Certification ECU (Smart key ECU assembly)
      Lock/unlock feedback lights	On	When the doors are locked by the entry lock function, the hazard warning lights flash once. When the doors are unlocked by the entry lock function, the hazard warning lights flash twice.	On or Off	Main body ECU (Multiplex network body ECU)
      Lock/unlock feedback-Tone*2	5	Buzzer answer-back volume.	Off, 1, 2, 3, 4, 5, 6 or 7	Main body ECU (Multiplex network body ECU)

      
      

      • *1: Default setting differs depending on the country.

      • *2: w/ Wireless Door Lock Buzzer Answer-back Function

3. Entry cancel function (manual operation)

   Tech Tips

   While the smart entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter sub-assembly near the engine switch.

   
   

   1. The following functions are disabled when the smart entry and start system is canceled.

      
      

      1. Entry unlock/lock functions

      2. Push-button start function

      3. Key lock-in prevention function

      4. Entry warning functions

   2. When canceling the smart entry and start system through manual operation:

      
      

      1. Make sure the following conditions are met:

      
      

      • The engine switch is off.

      • The driver door is closed.

      • The driver door is unlocked.

   3. Press the unlock switch of the electrical key transmitter sub-assembly.

   4. Open the driver door within 5 seconds of completing the step above (driver door: closed → opened).

   5. With the driver door open, press the unlock switch of the electrical key transmitter sub-assembly 2 times within 5 seconds of completing the step above.

      Note

      If the driver door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.

   6. Perform the following procedure within 30 seconds of completing the step above.

      
      

      1. Close and open the driver door twice (driver door: open → closed → opened → closed → opened).

      2. With the driver door open, press the unlock switch of the electrical key transmitter sub-assembly 2 times.

         Note

         If the driver door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.

      3. Close and open the driver door (driver door: open → closed → opened).

   7. Close the driver door within 5 seconds (driver door: open → closed).

   8. Check that the wireless buzzer sounds twice (short beeps) to confirm that the smart entry and start system has been canceled.

   9. Perform the following procedure to restore the smart entry and start system to the active state from the canceled state.

      
      

      1. Perform the procedure to cancel the smart entry and start system again.

      2. Check that the wireless buzzer sounds once (short beep) to confirm that the smart entry and start system has been restored to the active state.

         Tech Tips

         
         

         • The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.

         • The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.