FRONT DOOR LOCK INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for both the LH and RH sides.

  • The procedure described below is for the LH side.

PROCEDURE


  1. INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY


    1. B006M61

      Engage the guide to install the front door inside locking cable assembly to the front door lock assembly.

  2. INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    1. B006LHO

      Engage the guide to install the front door lock remote control cable assembly to the front door lock assembly.

  3. INSTALL FRONT DOOR LOCK COVER SUB-ASSEMBLY


    1. B006PBS

      Engage the hinges.

    2. B006OEAC01
      B006N8A Install in this Direction

      Engage the claws to install the front door lock cover sub-assembly as shown in the illustration.

  4. INSTALL FRONT DOOR LOCK ASSEMBLY

    Note


    • When reusing a removed front door lock assembly, replace the door lock wiring harness seal with a new one.

    • Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.

    • Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the front door lock assembly.


    1. Apply MP grease to the sliding parts of the front door lock assembly.

    2. When reusing the front door lock assembly:


      1. Install a new door lock wiring harness seal to the front door lock assembly.

    3. B006QO8C01
      *1 Front Door Lock Open Rod
      B006N8A Install in this Direction

      Connect the front door lock open rod to install the front door lock assembly as shown in the illustration.

      Tech Tips

      Make sure that the front door lock open rod is securely connected to the front door lock assembly.

    4. Using a T30 "TORX" socket wrench, install the front door lock assembly with the 3 screws.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    5. Connect the connector.

  5. INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)

    Click here

  6. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

    Click here

  7. INSTALL FRONT DOOR GLASS RUN

    Click here

  8. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

    Click here

  9. INSTALL FRONT DOOR SERVICE HOLE COVER

    Click here

  10. INSTALL FRONT DOOR REAR BELT SEAL

    Click here

  11. INSTALL FRONT DOOR FRONT BELT SEAL

    Click here

  12. INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP

    Click here

  13. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

    Click here

  14. INSTALL COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

    Click here

  15. INSTALL REFLEX REFLECTOR (w/o Courtesy Light)

    Click here

  16. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG

    Click here

  17. INSTALL DOOR FRAME LOWER GARNISH

    Click here

  18. INSTALL FRONT ARMREST ASSEMBLY

    Click here

  19. INSTALL FRONT ARMREST BASE UPPER PANEL LH (for Driver Side)

    Click here

  20. INSTALL FRONT ARMREST BASE UPPER PANEL RH (for Front Passenger Side)

    Click here

  21. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Torque:
    5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  22. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here

  23. INSPECT POWER WINDOW OPERATION

    Click here