FRONT DOOR LOCK REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front door lock removal/installation are shown below.

Necessary procedure after parts removed/installed/replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Disconnect cable from negative battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and Start System (for 2AR-FE)

Click here

Stop and Start System (for 2GR-FKS)

Click here

Memorize steering angle neutral point Panoramic view monitor system

Click here

Initialize back door lock Power door lock control system

Click here

Initialize servo motor Air conditioning system

Click here

Reset slide door close position Power slide door system

Click here

Reset back door close position Power back door system

Click here


  • Front door glass sub-assembly

  • Front door glass run

 Initialize Power Window Control System

  • Auto up and down function

  • Jam protection function

  • Remote control function

  • Key-linked function

  • Wireless transmitter-linked function

  • Key-off operation function

  • Catch protection function

  • Window open warning function

Click here

Tech Tips


  • Use the same procedure for both the LH and RH sides.

  • The procedure described below is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE FRONT ARMREST BASE UPPER PANEL LH (for Driver Side)

    Click here

  4. REMOVE FRONT ARMREST BASE UPPER PANEL RH (for Front Passenger Side)

    Click here

  5. REMOVE FRONT ARMREST ASSEMBLY

    Click here

  6. REMOVE DOOR FRAME LOWER GARNISH

    Click here

  7. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG

    Click here

  8. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

    Click here

  9. REMOVE REFLEX REFLECTOR (w/o Courtesy Light)

    Click here

  10. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

    Click here

  11. REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP

    Click here

  12. REMOVE FRONT DOOR FRONT BELT SEAL

    Click here

  13. REMOVE FRONT DOOR REAR BELT SEAL

    Click here

  14. REMOVE FRONT DOOR SERVICE HOLE COVER

    Click here

  15. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

    Click here

  16. REMOVE FRONT DOOR GLASS RUN

    Click here

  17. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

    Click here

  18. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)

    Click here

  19. REMOVE FRONT DOOR LOCK ASSEMBLY


    1. B006PM7C01
      *1 Front Door Lock Open Rod
      B006N8A Remove in this Direction

      Disconnect the connector.

    2. Using a T30 "TORX" socket wrench, remove the 3 screws.

    3. Disconnect the front door lock open rod to remove the front door lock assembly as shown in the illustration.

    4. When reusing the front door lock assembly:


      1. B006OPA

        Remove the door lock wiring harness seal from the front door lock assembly.

  20. REMOVE FRONT DOOR LOCK COVER SUB-ASSEMBLY


    1. B006QENC01
      *a Protective Tape
      B006N8A Remove in this Direction

      Using a screwdriver with its tip wrapped in protective tape, disengage the claws as shown in the illustration.

    2. B006PBS

      Disengage the hinges to remove the front door lock cover sub-assembly from the front door lock assembly.

  21. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    1. B006LHO

      Disengage the guide to remove the front door lock remote control cable assembly from the front door lock assembly.

  22. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY


    1. B006M61

      Disengage the guide to remove the front door inside locking cable assembly from the front door lock assembly.