POWER DOOR LOCK CONTROL SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body or Master Switch / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Main Body > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      ACC SW Engine switch (ACC) signal OFF or ON

      OFF: Engine switch off

      ON: Engine switch (ACC)

      		 -
      IG SW Engine switch on (IG) signal OFF or ON

      OFF: Engine switch off or (ACC)

      ON: Engine switch on (IG)

      		 -
      RR Door Courtesy SW Rear door courtesy light switch assembly RH signal OFF or ON

      OFF: Slide door RH closed

      ON: Slide door RH open

      		 -
      RL Door Courtesy SW Rear door courtesy light switch assembly LH signal OFF or ON

      OFF: Slide door LH closed

      ON: Slide door LH open

      		 -
      Back Door Courtesy SW Back door courtesy switch signal OFF or ON

      OFF: Back door closed

      ON: Back door open

      		 -
      Back Door Open Back door lock signal Prohibit or Permit

      Prohibit: Back door locked

      Permit: Back door unlocked

      		 -
      Door Key SW-Lock Driver door key-linked lock/unlock switch lock signal OFF or ON

      OFF: Driver door key cylinder not turned to lock position

      ON: Driver door key cylinder turned to lock position

      		 -
      D Door Key SW-UL Driver door key-linked lock / unlock switch unlock signal OFF or ON

      OFF: Driver door key cylinder not turned to unlock position

      ON: Driver door key cylinder turned to unlock position

      		 -
      FR Door Lock Pos Front door RH unlock detection switch signal LOCK or UNLOCK

      LOCK: Front door RH locked

      UNLOCK: Front door RH unlocked

      		 -
      FR Door Courtesy SW Front door courtesy light switch assembly RH signal OFF or ON

      OFF: Front door RH closed

      ON: Front door RH open

      		 -
      FL Door Lock Pos Front door LH unlock detection switch signal LOCK or UNLOCK

      LOCK: Front door LH locked

      UNLOCK: Front door LH unlocked

      		 -
      FL Door Courtesy SW Front door courtesy light switch assembly LH signal OFF or ON

      OFF: Front door LH closed

      ON: Front door LH open

      		 -
      RR-Door Lock Pos SW Slide door RH unlock detection switch signal OFF or ON

      OFF: Slide door RH locked

      ON: Slide door RH unlocked

      		 -
      RL-Door Lock Pos SW Slide door LH unlock detection switch signal OFF or ON

      OFF: Slide door LH locked

      ON: Slide door LH unlocked

      		 -
      Auto Lock Speed-sensitive automatic door lock function OFF or ON Customize setting displayed -
      Auto Lock/Shift Shift-linked automatic door lock function OFF or ON Customize setting displayed -
      Auto Unlock/Shift Shift-linked automatic door unlock function OFF or ON Customize setting displayed -
      All Unlock/Open-Close Driver door-linked automatic door unlock function OFF or ON Customize setting displayed -
      The Number of DTC Number of trouble codes 0 to 255 Number of stored DTCs displayed -

      Body Electrical > Master Switch > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Door Lock Switch Status Multiplex network master switch assembly lock signal OFF or ON

      OFF: Lock side of multiplex network master switch assembly not pushed

      ON: Lock side of multiplex network master switch assembly pushed

      		 -
      Door Unlock Switch Status Multiplex network master switch assembly unlock signal OFF or ON

      OFF: Unlock side of multiplex network master switch assembly not pushed

      ON: Unlock side of multiplex network master switch assembly pushed

      		 -

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Active Test.

    5. Perform the Active Test according to the display on the GTS.


      Body Electrical > Main Body > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Door Lock Door lock motor OFF/Unlock/Lock -
      Trunk and Back-Door Open Back door lock motor OFF/ON -
      Shock Detection Unlock Operate door lock motor UNLOCK/LOCK -