REAR NO. 1 SEAT ASSEMBLY(for Power Captain Seat with Memory) REASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

B006LWS

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedures listed below are for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart.

    Click here

PROCEDURE


  1. INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH


    1. B006PZR

      Install the rear seat cushion frame sub-assembly LH to the No. 1 seat leg sub-assembly LH with the 6 nuts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  2. INSTALL POWER SEAT MOTOR ASSEMBLY


    1. B006MQO

      Install the power seat motor assembly with the 3 nuts.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }
    2. B006LV4C01
      B006N8A Install in this Direction

      While turning the cable end as shown in the illustration, connect it.

    3. Attach the cable clamp.

  3. INSTALL REAR SEAT WIRE LH (w/o Manual Walk-in Mechanism)


    1. B006R61

      Attach the claw and clamp to install the rear seat wire LH.

    2. Connect the 2 connectors.

  4. INSTALL REAR SEAT WIRE RH (w/ Manual Walk-in Mechanism)


    1. B006Q70

      Attach the claw and clamp to install the rear seat wire RH.

    2. Connect the 2 connectors.

  5. INSTALL SEAT TRACK CONTROL CABLE ASSEMBLY (w/o Manual Walk-in Mechanism)


    1. B006PBXC01
      B006N8A Install in this Direction

      While turning the cable end as shown in the illustration, connect it.

    2. Attach the cable clamp to install the seat track control cable assembly.

      Tech Tips

      Install at the middle level of the cable clamp (triple level) side.

      B006QQ8

  6. INSTALL SEATBACK FELT


    1. Clean and remove any oil from the installation area of the seatback felt.

    2. B006P3Q

      Install 2 new pieces of seatback felt.

      Tech Tips

      Adjust the felt according to R-End.

  7. INSTALL SEAT CUSHION CLIMATE CONTROL DUCT


    1. B006QWR

      Attach the claw to install the seat cushion climate control duct.

  8. INSTALL SEAT CLIMATE CONTROL BLOWER LH


    1. Lift up in installation direction (1) shown in the illustration to attach the hook.

      B006OPGC01
      B006N8A Install in this Direction (1) B006NJK Install in this Direction (2)

    2. Rotate the rear seat climate control blower LH in installation direction (2) shown in the illustration.

    3. Lift up in installation direction (1) shown in the illustration to attach the hook.

      B006Q4VC01
      B006N8A Install in this Direction (1) B006NJK Install in this Direction (2)

    4. Rotate the rear seat climate control blower LH in installation direction (2) shown in the illustration.

    5. Lift up in installation direction (1) shown in the illustration to attach the hook.

      B006OU8C01
      B006N8A Install in this Direction (1) B006NJK Install in this Direction (2)

    6. Push down the rear seat climate control blower LH in installation direction (2) shown in the illustration.

    7. B006OP8

      Return the clamp in the direction indicated by the arrow shown in the illustration.

    8. B006NVQ

      Install the rear seat climate control blower LH with the 2 screws.

    9. Connect the connector.

  9. INSTALL RECLINING ADJUSTING CABLE ASSEMBLY (w/ Manual Walk-in Mechanism)


    1. Set the reclining adjusting cable assembly as shown in the illustration.

      B006NC8C01
      *a Through the top of the frame *b Through the inside of the bracket
      *c Bracket - -

    2. Attach the hook and install the reclining adjusting cable assembly with a new cable tie.

  10. INSTALL RECLINING ADJUSTING CABLE ASSEMBLY RH (w/ Manual Walk-in Mechanism)


    1. Set the reclining adjusting cable assembly RH as shown in the illustration.

      B006RI2C02
      *a Through the hole of the seat leg *b Through the inside of the bracket
      *c Bracket - -

    2. Install the reclining adjusting cable assembly with a new cable tie.

  11. INSTALL NO. 1 SEAT BRACKET RH (w/ Manual Walk-in Mechanism)


    1. B006MLJ

      Attach the guide.

    2. Install the No. 1 seat bracket RH with the screw.

  12. INSTALL REAR NO. 1 SEAT INSIDE RECLINING ADJUSTER COVER (w/o Manual Walk-in Mechanism)


    1. Apply protective tape as shown in the illustration.

      B006M23C01
      *1 Protective Tape - -

    2. While turning the rear No. 1 seat inside reclining adjuster cover as shown in the illustration, install it.

      B006O2DC01
      B006N8A Install in this Direction - -
    3. B006MK2

      Install the screw.

  13. INSTALL REAR NO. 1 SEAT INSIDE RECLINING ADJUSTER COVER (w/ Manual Walk-in Mechanism)


    1. B006OLVC03
      B006N8A Install in this Direction

      Install the rear No. 1 seat inside reclining adjuster cover with the 2 clips.

  14. INSTALL RECLINING COVER PROTECTOR RH


    1. w/o Manual Walk-in Mechanism:


      1. B006QL5C01
        B006N8A Install in this Direction

        Install the reclining cover protector RH.

    2. w/ Manual Walk-in Mechanism:


      1. B006KTNC02
        B006N8A Install in this Direction

        Attach the guide.

      2. Install the reclining cover protector RH with the clip.

  15. INSTALL RECLINING COVER PROTECTOR RH


    1. w/o Manual Walk-in Mechanism:


      1. B006NWVC01
        B006N8A Install in this Direction

        Attach the claw and install the reclining cover protector RH with the 2 clips.

    2. w/ Manual Walk-in Mechanism:


      1. B006OS2C02
        B006N8A Install in this Direction

        Attach the guide.

      2. Install the reclining cover protector RH with the clip.

  16. INSTALL REAR NO. 1 SEAT INSIDE RECLINING ADJUSTER COVER (w/o Manual Walk-in Mechanism)


    1. B006NKZC01
      B006N8A Install in this Direction

      Attach the guide and install the rear No. 1 seat inside reclining adjuster cover with the clip.

  17. INSTALL REAR NO. 1 SEAT INSIDE RECLINING ADJUSTER COVER (w/ Manual Walk-in Mechanism)


    1. B006NTBC02
      B006N8A Install in this Direction

      Attach the guide and install the rear No. 1 seat inside reclining adjuster cover with the clip.

  18. INSTALL INSIDE RECLINING ADJUSTER COVER LH (w/o Manual Walk-in Mechanism)


    1. B006P2XC01
      B006N8A Install in this Direction

      Attach the clamp and install the inside reclining adjuster cover LH.

  19. INSTALL INSIDE RECLINING ADJUSTER COVER RH (w/ Manual Walk-in Mechanism)


    1. B006KMSC02
      B006N8A Install in this Direction

      Attach the guide.

    2. Install the inside reclining adjuster cover RH with the 2 screws.

  20. INSTALL NO. 1 SEATBACK FRAME SUB-ASSEMBLY LH (w/o Manual Walk-in Mechanism)


    1. Temporarily install the No. 1 seatback frame sub-assembly LH with the 4 bolts.

    2. B006PXJC01
      *1 Bolt A
      *2 Bolt B

      Tighten the 4 bolts to install the No. 1 seatback frame sub-assembly LH.

      Torque:
      for Bolt A
      55 N*m  { 561 kgf*cm, 41 ft.*lbf }
      for Bolt B
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Tech Tips

      Tighten the bolts while pushing the No. 1 seatback frame sub-assembly LH as shown in the illustration.

      B006QM2
    3. B006MFE

      Attach the wire harness clamp.

  21. INSTALL NO. 1 SEATBACK FRAME SUB-ASSEMBLY RH (w/ Manual Walk-in Mechanism)


    1. Temporarily install the No. 1 seatback frame sub-assembly RH with the 4 bolts.

    2. B006M08C02
      *1 Bolt A
      *2 Bolt B

      Tighten the 4 bolts to install the No. 1 seatback frame sub-assembly RH.

      Torque:
      for Bolt A
      55 N*m  { 561 kgf*cm, 41 ft.*lbf }
      for Bolt B
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Tech Tips

      Tighten the bolts while pushing the No. 1 seatback frame sub-assembly RH as shown in the illustration.

      B006MDV

    3. While turning the cable end as shown in the illustration, connect it.

      B006O27C01
      B006N8A Install in this Direction - -

    4. Attach the cable clamp.

      Tech Tips

      Install at the middle level of the cable clamp (triple level) side.

      B006QQ8

  22. INSTALL REAR NO. 1 SEAT INSIDE RECLINING ADJUSTER COVER


    1. B006MY6

      Install the rear No. 1 seat inside reclining adjuster cover with the 2 clips.

  23. INSTALL NO. 2 SEAT WIRE (w/o Manual Walk-in Mechanism)


    1. B006R6V

      Attach the clamp.

    2. Connect the 3 connectors and install the No. 2 seat wire.

  24. INSTALL REAR NO. 2 SEAT WIRE RH (w/ Manual Walk-in Mechanism)


    1. B006LDG

      Attach the clamp.

    2. Connect the 2 connectors and install the rear No. 2 seat wire RH.

  25. INSTALL REAR SEATBACK SPRING DAMPER RH


    1. B006L7U

      Install the rear seatback spring damper RH with the 2 nuts.

      Torque:
      14.5 N*m  { 148 kgf*cm, 11 ft.*lbf }

  26. INSTALL REAR SEATBACK SPRING DAMPER


    1. B006PXY

      Install the rear seatback spring damper with the 2 nuts.

      Torque:
      14.5 N*m  { 148 kgf*cm, 11 ft.*lbf }

  27. INSTALL REAR SEATBACK CLIMATE CONTROL BLOWER LH


    1. B006R2W

      Install the rear seatback climate control blower LH with the 4 screws.

    2. Connect the connector.

  28. INSTALL REAR NO. 1 SEATBACK CLIMATE CONTROL DUCT


    1. B006Q0D

      Install the rear No. 1 seatback climate control duct with the 4 screws.

  29. INSTALL REAR NO. 2 SEATBACK CLIMATE CONTROL DUCT


    1. B006P0Q

      Attach the claw to install the rear No. 2 seatback climate control duct.

  30. INSTALL POWER SEAT SWITCH BEZEL


    1. w/o Manual Walk-in Mechanism:


      1. B006MZD

        Install the power seat switch bezel with the 2 screws.

    2. w/ Manual Walk-in Mechanism:


      1. B006NDO

        Install the power seat switch bezel with the 2 screws.

  31. INSTALL REAR SEAT SHOULDER BELT COVER LH


    1. B006QKFC01
      B006N8A Install in this Direction

      Push as shown in the illustration to attach the guide.

    2. Attach the claw to install the rear seat shoulder belt cover LH.

  32. INSTALL NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH

    Click here

  33. INSTALL REAR SEAT INNER RECLINING COVER LH (w/o Manual Walk-in Mechanism)


    1. B006LKS

      Install the rear seat inner reclining cover LH with the 2 screws.

  34. INSTALL REAR SEAT INNER RECLINING COVER RH (w/ Manual Walk-in Mechanism)


    1. B006PHAC02
      B006N8A Install in this Direction

      Attach the claw.

    2. Install the rear seat inner reclining cover RH with the 2 screws.

  35. INSTALL REAR SEAT SHOULDER BELT COVER LH


    1. B006R9R

      Attach the claw to install the rear seat shoulder belt cover LH.

  36. INSTALL REAR NO. 2 SEAT PROTECTOR


    1. w/o Manual Walk-in Mechanism:


      1. B006NPOC04
        B006N8A Install in this Direction(1)
        B006NJK Install in this Direction(2)

        Attach the guide and set the rear No. 2 seat protector as shown in the illustration.

      2. B006QTDC01
        B006N8A Install in this Direction (1)
        B006NJK Install in this Direction (2)

        Attach the guide.

      3. Install the rear No. 2 seat protector with the 5 clips.

      4. B006R6RC01
        B006N8A Install in this Direction

        Install the seat track control cable assembly to the rear No. 2 seat protector.

    2. w/ Manual Walk-in Mechanism:


      1. B006QFDC07
        B006N8A Install in this Direction(1)
        B006NJK Install in this Direction(2)

        Attach the guide and set the rear No. 2 seat protector as shown in the illustration.

      2. B006NYYC02
        B006N8A Install in this Direction (1)
        B006NJK Install in this Direction (2)

        Attach the guide.

      3. Install the rear No. 2 seat protector with the 4 clips.

      4. B006OREC02
        B006N8A Install in this Direction

        Install the reclining adjusting cable assembly to the rear No. 2 seat protector.

  37. INSTALL NO. 3 FRAME WIRE


    1. B006PTK

      Attach the wire harness clamp to install the No. 3 frame wire.

    2. Connect the 2 connectors.

  38. INSTALL REAR SEAT LEGREST COVER


    1. B006R7H

      Install the rear seat legrest cover with the 4 screws.

  39. INSTALL REAR SEAT HEADREST SUPPORT


    1. B006KPVC01
      B006N8A Install in this Direction

      Attach the claw to install the 2 rear seat headrest supports.

  40. INSTALL REAR LOWER INNER RECLINING ADJUSTER ARM SUB-ASSEMBLY LH


    1. B006OBW

      Install the rear lower inner reclining adjuster arm sub-assembly LH with the 4 bolts.

      Torque:
      22 N*m  { 224 kgf*cm, 16 ft.*lbf }

    2. Attach the wire harness clamp.

    3. Connect the connector.

  41. INSTALL SEAT HEATER ASSEMBLY

    Click here

  42. INSTALL SEAT COVER WIRE


    1. B006Q6BN01

      Install the seat cover wire.

      Tech Tips


      • Wire 1000 mm (3.28 ft.) or longer and shaped wire are available as supplied parts.

      • When a wire that is less than 1000 mm in length is needed, cut or shape 1000 mm (3.28 ft.) wire into the dimensions shown in the illustration.

      • Make sure to read the precautions before preparing the wire.

        Click here

      Dimensions
      A 370 mm (1.21 ft.)
      B 240 mm (9.45 in.)
      C 260 mm (10.2 in.)

      Tech Tips

      The dimensions shown in the illustration are the lengths.

      B006OSZ

  43. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER

    Tech Tips


    • When installing the seat cover, refer to the precautions in order to prevent wrinkles from forming.

      Click here

    • Align the seam allowance in a single direction as shown in the illustration.

      B006KXAN01

    1. B006R96C01
      B006N8A Remove in this Direction

      Slide the seat cover wire until it reaches a position where the hog rings in the center can be installed.

    2. B006O4XC01
      *1 Hog Ring Pliers

      Using hog ring pliers, install the separate type rear seat cushion cover to the rear seat cushion pad LH with 4 new hog rings in the order shown in the illustration.

      Note


      • Be careful not to damage the separate type rear seat cushion cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.

    3. B006PN4C01
      B006N8A Install in this Direction

      Return the seat cover wire to its original position.

    4. B006NWCC01
      *1 Hog Ring Pliers

      Using hog ring pliers, install the separate type rear seat cushion cover to the rear seat cushion pad LH with 12 new hog rings in the order shown in the illustration.

      Note


      • Be careful not to damage the separate type rear seat cushion cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.

    5. B006Q1FC01
      *1 Hog Ring Pliers

      Using hog ring pliers, install the separate type rear seat cushion cover with 6 new hog rings in the order shown in the illustration.

      Note


      • Be careful not to damage the separate type rear seat cushion cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.

  44. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD


    1. B006KNE

      Attach the hook.

    2. B006QDYC01
      B006N8A Install in this Direction

      Rotate the separate type rear seat cushion cover with pad as shown in the illustration and attach the guide.

    3. Attach the hook to install the separate type rear seat cushion cover with pad.

      B006PZW

    4. Attach the claw of the seat cushion climate control duct.

    5. B006O0P

      Attach the claw and install the connector of the occupant detection sensor.

    6. B006LQY

      Connect the 2 connectors.

  45. INSTALL REAR SEAT CLIMATE CONTROL ECU LH


    1. B006RAZ

      Install the rear seat climate control ECU LH with the 2 nuts.

    2. Connect the connector.

  46. INSTALL POSITION CONTROL ECU ASSEMBLY


    1. B006LFG

      Install the position control ECU assembly with the 2 nuts.

    2. Connect the 3 connectors.

  47. INSTALL SEAT TRACK LOCK OPEN LEVER SUB-ASSEMBLY LH


    1. B006RAB

      Install the seat track lock open lever sub-assembly LH with the 2 nuts.

      Torque:
      14 N*m  { 143 kgf*cm, 10 ft.*lbf }

    2. Connect the connector.

  48. INSTALL REAR NO. 1 SEAT FOOTREST COVER


    1. B006LEDC01
      B006N8A Install in this Direction

      Attach the guide and install the rear No. 1 seat footrest cover.

    2. B006OD8

      Attach the claw.

  49. INSTALL REAR SEAT FOOTREST PANEL


    1. B006MZGC01
      B006N8A Install in this Direction

      Install the rear seat footrest panel to the rear seat footrest frame.

  50. INSTALL REAR SEAT FOOTREST COVER SUB-ASSEMBLY RH


    1. B006QT8C02
      B006N8A Install in this Direction

      Attach the hook.

    2. Install the rear seat footrest cover with the 6 clips in the order shown in the illustration.

    3. B006M3GC01
      B006N8A Install in this Direction

      Install the rear seat footrest assembly with the 2 bolts.

      Torque:
      14 N*m  { 143 kgf*cm, 10 ft.*lbf }

  51. INSTALL REAR SEAT LEGREST COVER


    1. B006KI5

      Install the rear seat legrest cover with the 2 screws.

  52. INSTALL REAR SEAT LEG COVER LH


    1. B006OLZC01
      B006N8A Install in this Direction

      Attach the clip and guide to install the rear seat leg cover LH.

  53. INSTALL REAR SEAT LEG SIDE COVER LH


    1. B006LA4C01
      B006N8A Install in this Direction

      Attach the clip to install the rear seat leg side cover LH.

  54. INSTALL REAR NO. 1 SEAT INSIDE RECLINING ADJUSTER COVER


    1. B006QRWC01
      B006N8A Install in this Direction

      Attach the clip and claw to install the rear No. 1 seat inside reclining adjuster cover.

  55. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

    Click here

  56. INSTALL SEAT HEATER ASSEMBLY

    Click here

  57. INSTALL SEAT COVER WIRE


    1. Install the seat cover wire.

      Tech Tips


      • Wire 1000 mm (3.28 ft.) or longer and shaped wire are available as supplied parts.

      • When a wire that is less than 1000 mm in length is needed, cut or shape 1000 mm (3.28 ft.) wire into the dimensions shown in the illustration.

      • Make sure to read the precautions before preparing the wire.

        Click here

      B006O0LN01
      Dimensions
      A 260 mm (10.2 in.) B 530 mm (1.74 ft.)
      C 350 mm (1.15 ft.) - -

      Tech Tips

      The dimensions shown in the illustration are the lengths.

      B006OSZ

  58. INSTALL SEPARATE TYPE REAR SEATBACK COVER

    Tech Tips


    • When installing the seat cover, refer to the precautions in order to prevent wrinkles from forming.

      Click here

    • Align the seam allowance in a single direction as shown in the illustration.

      B006OLON01

    1. B006L66C01
      B006N8A Remove in this Direction

      Slide the seat cover wire until it reaches a position where the hog rings in the center can be installed.

    2. B006QB3C01
      *1 Hog Ring Pliers

      Using hog ring pliers, install the separate type rear seatback cover to the separate type rear seatback pad with 2 new hog rings in the order shown in the illustration.

      Note


      • Be careful not to damage the separate type rear seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.

    3. B006MRNC01
      B006N8A Install in this Direction

      Return the seat cover wire to its original position.

    4. B006OOUC01
      *1 Hog Ring Pliers

      Using hog ring pliers, install the separate type rear seatback cover to the separate type rear seatback pad with 10 new hog rings in the order shown in the illustration.

      Note


      • Be careful not to damage the separate type rear seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.

  59. INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD


    1. B006QH3C01
      B006N8A Install in this Direction (1)
      B006NJK Install in this Direction (2)

      Push in installation direction (1) shown in the illustration to install the separate type rear seatback cover with pad.

    2. Push in the rear end of the separate type rear seatback cover with pad in installation direction (2) shown in the illustration.

    3. B006MQF

      Attach the hook.

    4. B006MEDC01
      *a Protrusion
      B006N8A Install in this Direction

      Align the rear seat headrest support protrusions with the grooves in the No. 1 seatback frame sub-assembly LH.

    5. Push as shown in the illustration and attach the claw to install the 2 rear seat headrest supports.

    6. w/o Manual Walk-in Mechanism:


      1. B006RJL

        Connect the connector of the seat heater assembly.

    7. w/ Manual Walk-in Mechanism:


      1. B006OV4

        Pass the rear seat wire RH through the slit of the separate type rear seatback cover.

      2. Attach the clamp.

      3. Connect the 2 connectors.

    8. B006QU8

      Attach the claw.

    9. B006PKJ

      Return the rear No. 2 seat protector.

    10. B006MMW

      Close the 2 fasteners.

    11. Store the 2 fasteners.

      B006LWF

    12. w/o Manual Walk-in Mechanism:


      1. B006QW1C01
        *1 Hog Ring Pliers

        Using hog ring pliers, install 3 new hog rings in the order shown in the illustration.

        Note


        • Be careful not to damage the separate type rear seatback cover.

        • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.

    13. w/ Manual Walk-in Mechanism:


      1. B006QOZC02
        *1 Hog Ring Pliers

        Using hog ring pliers, install 5 new hog rings in the order shown in the illustration.

        Note


        • Be careful not to damage the separate type rear seatback cover.

        • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.

  60. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY


    1. B006RFA

      Pull out the seat track control cable assembly.

    2. B006MBAC01
      B006N8A Install in this Direction

      While turning the seat track control cable assembly as shown in the illustration, connect it.

    3. Attach the cable clamp.

    4. B006MDP

      Install the rear seat lock control lever sub-assembly with the 2 screws.

  61. INSTALL SEAT STAND FRAME CAP


    1. B006PHF

      Attach the claw to install the seat stand frame cap.

  62. INSTALL REAR SEAT SHOULDER BELT COVER LH


    1. B006QGHC01
      B006N8A Install in this Direction

      Attach the rear seat shoulder belt cover LH to the No. 1 seat 3 point type belt assembly LH as shown in the illustration.

    2. B006MOQ

      Attach the claw to install the rear seat shoulder belt cover LH.

  63. INSTALL NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH (SEAT ANCHOR)


    1. Check that the No. 1 seat 3 point type belt assembly LH is not twisted.

    2. B006QRTC01
      *1 Protruding Part

      Install the seat anchor of the No. 1 seat 3 point type belt assembly LH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      The anchor part of the No. 1 seat 3 point type belt assembly LH must not overlap the protruding part.

  64. INSTALL REAR NO. 3 POWER SEAT SWITCH

    Click here

  65. INSTALL REAR NO. 1 SEAT INSIDE RECLINING ADJUSTER COVER


    1. B006N92C01
      B006N8A Install in this Direction

      Push as shown in the illustration to attach the claw and guide to install the rear No. 1 seat inside reclining adjuster cover.

  66. INSTALL REAR SEAT ARMREST FRAME SUB-ASSEMBLY RH


    1. B006N3F

      Attach the clip and guide.

    2. B006RI3N01

      Install the rear seat armrest frame sub-assembly RH with the 7 bolts in the order shown in the illustration.

      Torque:
      14 N*m  { 143 kgf*cm, 10 ft.*lbf }

    3. for RH Side:


      1. B006N7O

        Install the washer.

    4. B006M3E

      Install the 2 bolts.

      Torque:
      4.5 N*m  { 46 kgf*cm, 40 in.*lbf }

  67. INSTALL REAR SEAT TURN TABLE ASSEMBLY LH


    1. B006RE3C02
      B006Q1Z Place Hands Here
      B006N8A Install in this Direction

      Attach the guide and install the rear seat turn table assembly LH with the 6 nuts in the order shown in the illustration.

      Torque:
      14 N*m  { 143 kgf*cm, 10 ft.*lbf }

      CAUTION:

      Do not place your hands in the openings in the sliding parts as this may result in injury.

      B006RFTC01
      B006REL Opening in Sliding Parts - -

      Note

      Do not hold the bottom parts of the rear seat turn table assembly LH.

  68. INSTALL REAR NO. 1 SEAT LEG BRACKET


    1. B006P97

      Temporarily install the rear No. 1 seat leg bracket with the 2 nuts and bolt.

    2. While pressing the rear No. 1 seat leg bracket against the No. 1 seat leg sub-assembly LH and rear seat turn table assembly LH, tighten the 2 nuts.

      Torque:
      4.5 N*m  { 46 kgf*cm, 40 in.*lbf }

    3. Tighten the bolt.

      Torque:
      4.5 N*m  { 46 kgf*cm, 40 in.*lbf }

  69. INSTALL NO. 1 CUP HOLDER ASSEMBLY


    1. B006LBY

      Attach the claw to install the No. 1 cup holder assembly with the 2 screws.

  70. INSTALL REAR NO. 1 SEAT ARMREST ASSEMBLY RH


    1. Push as shown in the illustration to attach the claw and clip.

      B006PCMC02
      B006N8A Install in this Direction - -
    2. B006OYR

      Install the rear No. 1 seat armrest assembly RH with the 7 bolts.

      Torque:
      4.5 N*m  { 46 kgf*cm, 40 in.*lbf }

  71. INSTALL REAR SEAT CUSHION MOULDING LH


    1. B006NQYC01
      B006N8A Install in this Direction

      Push as shown in the illustration to attach the guide and claw.

    2. B006LDEC01
      B006N8A Install in this Direction

      Push as shown in the illustration and attach the claw and clip to install the rear seat cushion moulding LH.

  72. INSTALL SEAT ADJUSTER COVER CAP RH (w/o Manual Walk-in Mechanism)


    1. B006ONKC01
      B006N8A Install in this Direction

      Push as shown in the illustration, attach the guide and claw to install the seat adjuster cover cap RH.

  73. INSTALL SEAT ADJUSTER COVER CAP LH (w/ Manual Walk-in Mechanism)


    1. B006L6MC02
      B006Q1Z Place Hands Here
      B006N8A Install in this Direction

      Push as shown in the illustration, attach the guide and claw to install the seat adjuster cover cap LH.

  74. INSTALL SEAT LEG GARNISH COVER


    1. B006L0F

      Attach the claw to install the seat leg garnish cover.

  75. INSTALL RECLINING ADJUSTER COVER RH

    Note

    Do not reuse the reclining adjuster cover RH after removing it.


    1. B006MRM

      Connect the connector.

    2. B006P47C01
      B006N8A Install in this Direction

      Push as shown in the illustration, attach the guide, clip and claw to install a new reclining adjuster cover RH.

  76. INSTALL REAR NO. 1 SEAT INSIDE RECLINING ADJUSTER COVER


    1. B006OWO

      Attach the guide and clip.

    2. B006MK9

      Install the rear No. 1 seat inside reclining adjuster cover to the rear seat armrest frame sub-assembly LH with the 2 bolts and screw.

      Torque:
      for Bolt
      4.5 N*m  { 46 kgf*cm, 40 in.*lbf }

  77. INSTALL REAR SEAT ARMREST FRAME SUB-ASSEMBLY LH


    1. B006PA7

      Clean and remove any oil from the threads of the 2 stud bolts for the rear seat cushion frame sub-assembly LH and those of the 2 fixing nuts for the rear seat armrest frame sub-assembly LH.

    2. Apply adhesive to the threads of the 2 fixing nuts.

      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
    3. B006LMQ

      Install the rear seat armrest frame sub-assembly LH together with the rear No. 1 seat inside reclining adjuster cover with the 2 bolts and 2 nuts.

      Torque:
      14 N*m  { 143 kgf*cm, 10 ft.*lbf }

    4. w/o Manual Walk-in Mechanism:


      1. B006RF2

        Attach the clamp.

    5. w/ Manual Walk-in Mechanism:


      1. B006RGF

        Attach the clamp.

  78. INSTALL REAR OUTER SEAT TRACK COVER SUB-ASSEMBLY RH (w/ Manual Walk-in Mechanism)


    1. B006P3GC02
      B006N8A Install in this Direction

      While turning the cable end as shown in the illustration, connect it.

    2. Attach the cable clamp.

    3. B006NEFC02
      B006N8A Install in this Direction

      Attach the hook.

    4. B006L87

      Temporarily install the rear outer seat track cover sub-assembly RH with the 2 screws.

  79. INSTALL REAR SEAT RECLINING COVER LH (w/o Manual Walk-in Mechanism)


    1. B006LHIC01
      B006N8A Install in this Direction

      Push as shown in the illustration to attach the claw and clip.

    2. B006KPLC03
      *1 Bolt
      *2 Screw

      Install the rear seat reclining cover LH with the bolt.

      Torque:
      4.5 N*m  { 46 kgf*cm, 40 in.*lbf }

    3. Install the screw.

  80. INSTALL REAR SEAT RECLINING COVER RH (w/ Manual Walk-in Mechanism)


    1. B006ONJC02
      B006N8A Install in this Direction

      Push as shown in the illustration and attach the guide, claw and clip to install the rear seat reclining cover RH.

    2. Tighten the 2 screws of the rear outer seat track cover sub-assembly RH.

    3. B006LHFC06
      *1 Bolt
      *2 Screw

      Install the rear seat reclining cover RH with the bolt.

      Torque:
      4.5 N*m  { 46 kgf*cm, 40 in.*lbf }

    4. Install the screw.

  81. INSTALL SEAT STAND FRAME CAP (w/ Manual Walk-in Mechanism)


    1. B006P95C02
      B006N8A Install in this Direction

      Attach the claw and install the seat stand frame cap.

  82. INSTALL SEAT ADJUSTER COVER CAP LH (w/o Manual Walk-in Mechanism)


    1. B006Q8PC01
      B006N8A Install in this Direction

      Push as shown in the illustration, attach the guide and claw to install the seat adjuster cover cap LH.

  83. INSTALL SEAT ADJUSTER COVER CAP RH (w/ Manual Walk-in Mechanism)


    1. B006MAAC02
      B006Q1Z Place Hands Here
      B006N8A Install in this Direction

      Push as shown in the illustration, attach the guide and claw to install the seat adjuster cover cap RH.

  84. INSTALL REAR SEAT CUSHION


    1. B006P2P

      Install the rear seat cushion with the screw.

  85. INSTALL REAR POWER SEAT SWITCH LH

    Click here

  86. INSTALL REAR NO. 1 SEAT ARMREST ASSEMBLY LH


    1. B006PUUC01
      B006N8A Install in this Direction

      Push as shown in the illustration and attach the claw to install the rear seat armrest assembly LH.

    2. B006OUU

      Install the 4 bolts.

      Torque:
      4.5 N*m  { 46 kgf*cm, 40 in.*lbf }

    3. Attach the clamp and connect the connector.

  87. INSTALL REAR NO. 1 SEAT RECLINING COVER LH


    1. B006LMK

      Attach the clamp.

    2. B006LA5C01
      B006N8A Install in this Direction

      Push as shown in the illustration and attach the claw to install the rear No. 1 seat reclining cover LH.

  88. INSTALL REAR POWER SEAT SWITCH LH

    Click here

  89. INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE LH


    1. B006N8CC01
      B006N8A Install in this Direction

      Push as shown in the illustration and attach the claw to install the No. 1 reclining adjuster release handle LH.