AUDIO AND VISUAL SYSTEM(for Radio and Display Type), Diagnostic DTC:B15C3

DTC Code DTC Name
B15C3 Speaker Output Short

DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C3 Speaker Output Short A short is detected in the speaker output circuit

  • Harness or connector

  • Speaker

  • Telematics transceiver*

  • Radio and display receiver assembly

WIRING DIAGRAM


  1. w/o Manual (SOS) Switch

    B006OYOE02

  2. w/ Manual (SOS) Switch

    B006NNDE01

PROCEDURE


  1. CHECK MODEL


    1. Choose the model to be inspected.

      Result
      Result Proceed to
      w/o Manual (SOS) Switch A
      w/ Manual (SOS) Switch B

    B

    CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BODY GROUND) Click here

    A

  2. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BODY GROUND)


    1. Disconnect the F37 and F38 radio and display receiver assembly connectors.

    2. Disconnect the H2 and H4 front No. 2 speaker assembly connectors.

    3. Disconnect the d1 and d2 rear No. 2 speaker assembly connectors.

    4. Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F37-1 (FR+) - Body ground Always 10 kΩ or higher
      F37-5 (FR-) - Body ground Always 10 kΩ or higher
      F37-2 (FL+) - Body ground Always 10 kΩ or higher
      F37-6 (FL-) - Body ground Always 10 kΩ or higher
      F38-1 (RR+) - Body ground Always 10 kΩ or higher
      F38-3 (RR-) - Body ground Always 10 kΩ or higher
      F38-2 (RL+) - Body ground Always 10 kΩ or higher
      F38-6 (RL-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (FRONT AND REAR NO. 2 SPEAKER ASSEMBLY - BODY GROUND)


    1. Disconnect the I1 and I17 front No. 1 speaker assembly connectors.

    2. Disconnect the H2 and H4 front No. 2 speaker assembly connectors.

    3. Disconnect the J10 and J23 rear No. 1 speaker assembly connectors.

    4. Disconnect the d1 and d2 rear No. 2 speaker assembly connectors.

    5. Measure the resistance between each of the speaker assemblies and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H2-3 (+) - Body ground Always 10 kΩ or higher
      H2-1 (-) - Body ground Always 10 kΩ or higher
      H4-3 (+) - Body ground Always 10 kΩ or higher
      H4-1 (-) - Body ground Always 10 kΩ or higher
      d1-3 (+) - Body ground Always 10 kΩ or higher
      d1-1 (-) - Body ground Always 10 kΩ or higher
      d2-3 (+) - Body ground Always 10 kΩ or higher
      d2-1 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. B006QNGC30
      *a

      Component without harness connected

      (Front No. 1 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Always 3.2 to 4.8 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

    OK

  5. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. B006QOYC47
      *A for RH
      *B for LH
      *a

      Component without harness connected

      (Front No. 2 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      4 (TWR+) - 2 (TWR-) Always 10 kΩ or higher
      3 (+) - 4 (TWR+) Always Below 1 Ω
      1 (-) - 2 (TWR-) Always Below 1 Ω
      4 (TWL+) - 2 (TWL-) Always 10 kΩ or higher
      3 (+) - 4 (TWL+) Always Below 1 Ω
      1 (-) - 2 (TWL-) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY Click here

    OK

  6. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY


    1. Replace the front No. 2 speaker assembly with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    3. Recheck for DTCs and check that no DTCs are output.


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.

      Tech Tips


      • Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.

      • When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.

      • Perform the above inspection on both the LH and RH side.

      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

  7. INSPECT REAR NO. 1 SPEAKER ASSEMBLY


    1. Remove the rear No. 1 speaker assembly.

      Click here

    2. B006QNGC30
      *a

      Component without harness connected

      (Rear No. 1 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Always 3.2 to 4.8 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY Click here

    NG

  8. INSPECT REAR NO. 2 SPEAKER ASSEMBLY


    1. Remove the rear No. 2 speaker assembly.

      Click here

    2. B006QOYC68
      *a

      Component without harness connected

      (Rear No. 2 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      4 (+TW) - 2 (-TW) Always 10 kΩ or higher
      3 (+) - 4 (+TW) Always Below 1 Ω
      1 (-) - 2 (-TW) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR NO. 2 SPEAKER ASSEMBLY Click here

    OK

  9. REPLACE REAR NO. 2 SPEAKER ASSEMBLY


    1. Replace the rear No. 2 speaker assembly with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    3. Recheck for DTCs and check that no DTCs are output.


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.

      Tech Tips


      • Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.

      • When there is a possibility that either the right or left rear No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.

      • Perform the above inspection on both the LH and RH side.

      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY Click here

  10. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BODY GROUND)


    1. Disconnect the F37 and F38 radio and display receiver assembly connectors.

    2. Disconnect the M1 telematics transceiver connector.

    3. Disconnect the H4 front No. 2 speaker assembly LH connector.

    4. Disconnect the d1 and d2 rear No. 2 speaker assembly connectors.

    5. Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F37-1 (FR+) - Body ground Always 10 kΩ or higher
      F37-5 (FR-) - Body ground Always 10 kΩ or higher
      F37-2 (FL+) - Body ground Always 10 kΩ or higher
      F37-6 (FL-) - Body ground Always 10 kΩ or higher
      F38-1 (RR+) - Body ground Always 10 kΩ or higher
      F38-3 (RR-) - Body ground Always 10 kΩ or higher
      F38-2 (RL+) - Body ground Always 10 kΩ or higher
      F38-6 (RL-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  11. CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - BODY GROUND)


    1. Disconnect the M1 telematics transceiver connector.

    2. Disconnect the H2 front No. 2 speaker assembly RH connector.

    3. Measure the resistance between the telematics transceiver and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      M1-5 (SPO+) - Body ground Always 10 kΩ or higher
      M1-6 (SPO-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  12. CHECK HARNESS AND CONNECTOR (FRONT AND REAR NO. 2 SPEAKER ASSEMBLY - BODY GROUND)


    1. Disconnect the I1 and I17 front No. 1 speaker assembly connectors.

    2. Disconnect the H2 and H4 front No. 2 speaker assembly connectors.

    3. Disconnect the J10 and J23 rear No. 1 speaker assembly connectors.

    4. Disconnect the d1 and d2 rear No. 2 speaker assembly connectors.

    5. Measure the resistance between each of the speaker assemblies and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H2-3 (+) - Body ground Always 10 kΩ or higher
      H2-1 (-) - Body ground Always 10 kΩ or higher
      H4-3 (+) - Body ground Always 10 kΩ or higher
      H4-1 (-) - Body ground Always 10 kΩ or higher
      d1-3 (+) - Body ground Always 10 kΩ or higher
      d1-1 (-) - Body ground Always 10 kΩ or higher
      d2-3 (+) - Body ground Always 10 kΩ or higher
      d2-1 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  13. INSPECT TELEMATICS TRANSCEIVER


    1. Remove the telematics transceiver.

      Click here

    2. B006RKVC26
      *a

      Component without harness connected

      (Telematics Transceiver)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 (SPI+) - 5 (SPO+) Always Below 1 Ω
      3 (SPI-) - 6 (SPO-) Always Below 1 Ω
      2 (SPI+) - 3 (SPI-) Always 10 kΩ or higher
      5 (SPO+) - 6 (SPO-) Always 10 kΩ or higher
      2 (SPI+) or 5 (SPO+) - Body ground Always 10 kΩ or higher
      3 (SPI-) or 6 (SPO-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE TELEMATICS TRANSCEIVER Click here

    OK

  14. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. B006QNGC30
      *a

      Component without harness connected

      (Front No. 1 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Always 3.2 to 4.8 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

    OK

  15. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. B006QOYC47
      *A for RH
      *B for LH
      *a

      Component without harness connected

      (Front No. 2 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      4 (TWR+) - 2 (TWR-) Always 10 kΩ or higher
      3 (+) - 4 (TWR+) Always Below 1 Ω
      1 (-) - 2 (TWR-) Always Below 1 Ω
      4 (TWL+) - 2 (TWL-) Always 10 kΩ or higher
      3 (+) - 4 (TWL+) Always Below 1 Ω
      1 (-) - 2 (TWL-) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY Click here

    OK

  16. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY


    1. Replace the front No. 2 speaker assembly with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    3. Recheck for DTCs and check that no DTCs are output.


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.

      Tech Tips


      • Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.

      • When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.

      • Perform the above inspection on both the LH and RH side.

      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

  17. INSPECT REAR NO. 1 SPEAKER ASSEMBLY


    1. Remove the rear No. 1 speaker assembly.

      Click here

    2. B006QNGC30
      *a

      Component without harness connected

      (Rear No. 1 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Always 3.2 to 4.8 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY Click here

    NG

  18. INSPECT REAR NO. 2 SPEAKER ASSEMBLY


    1. Remove the rear No. 2 speaker assembly.

      Click here

    2. B006QOYC68
      *a

      Component without harness connected

      (Rear No. 2 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      4 (+TW) - 2 (-TW) Always 10 kΩ or higher
      3 (+) - 4 (+TW) Always Below 1 Ω
      1 (-) - 2 (-TW) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR NO. 2 SPEAKER ASSEMBLY Click here

    OK

  19. REPLACE REAR NO. 2 SPEAKER ASSEMBLY


    1. Replace the rear No. 2 speaker assembly with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    3. Recheck for DTCs and check that no DTCs are output.


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.

      Tech Tips


      • Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.

      • When there is a possibility that either the right or left rear No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.

      • Perform the above inspection on both the LH and RH side.

      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY Click here