LIN COMMUNICATION SYSTEM, Diagnostic DTC:B2785

DTC Code DTC Name
B2785 Communication Malfunction between ECUs Connected by LIN

DESCRIPTION

The certification ECU (smart key ECU assembly) monitors communication between all the ECUs connected to the certification bus lines. When the certification ECU (smart key ECU assembly) detects errors in communication with all the ECUs connected to the certification bus lines at a set interval and 3 times in a row, DTC B2785 will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2785 Communication Malfunction between ECUs Connected by LIN

  • Errors in LIN communication between ECUs or an open or short in communication lines.

  • LIN communication error detected by the certification ECU (smart key ECU assembly) 3 times in a row.

  • Certification ECU (smart key ECU assembly)

  • Steering lock ECU (steering lock actuator or upper bracket assembly)

  • ID code box (immobiliser code ECU)

  • Wire harness or connector

  • STRG LOCK fuse

  • ECU-B NO. 3 fuse

WIRING DIAGRAM

A01ILCKE53

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • If the certification ECU (smart key ECU assembly), steering lock ECU (steering lock actuator or upper bracket assembly) or ID code box (immobiliser code ECU) is replaced, refer to Service Bulletin.

  • Before performing the inspection, check that DTC B2786, B2789 or B278C is not output.

    Click here

  • When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - EACH ECU)


    1. Disconnect the G22 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the G26 steering lock ECU (steering lock actuator or upper bracket assembly) connector.

    3. Disconnect the G15 ID code box (immobiliser code ECU) connector.

    4. Measure the resistance according to the value(s) in the table below.

      Note

      Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the engine switch from on (IG) to off and wait for 180 seconds or more without operating any switches.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G22-6 (LIN) - G26-5 (LIN) Engine switch off Below 1 Ω
      G22-6 (LIN) - G15-2 (LIN1) Engine switch off Below 1 Ω
      G22-6 (LIN) - Body ground Engine switch off 10 kΩ or higher
      G26-5 (LIN) - Body ground Engine switch off 10 kΩ or higher
      G15-2 (LIN1) - Body ground Engine switch off 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. CHECK DTC OUTPUT (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY))


    1. Reconnect the G22 certification ECU (smart key ECU assembly) connector.

    2. Reconnect the G15 ID code box (immobiliser code ECU) connector.

    3. Clear the DTCs.

      Click here


      Body Electrical > Entry&Start > Clear DTCs

    4. Recheck for DTCs.


      Body Electrical > Entry&Start > Trouble Codes
      Result
      Result Proceed to
      DTC B2785 is output A
      DTC B2785 is not output B

    B

    REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) Click here

    A

  3. CHECK DTC OUTPUT (ID CODE BOX (IMMOBILISER CODE ECU))


    1. Reconnect the G26 steering lock ECU (steering lock actuator or upper bracket assembly) connector.

    2. Disconnect the G15 ID code box (immobiliser code ECU) connector.

    3. Clear the DTCs.

      Click here


      Body Electrical > Entry&Start > Clear DTCs

    4. Recheck for DTCs.


      Body Electrical > Entry&Start > Trouble Codes
      Result
      Result Proceed to
      DTC B2785 is output A
      DTC B2785 is not output B

    A

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    B

    REPLACE ID CODE BOX (IMMOBILISER CODE ECU)