AUTOMATIC TRANSAXLE SYSTEM, Diagnostic DTC:P056014

DTC Code DTC Name
P056014 System Voltage Circuit Short to Ground or Open

DESCRIPTION

The battery supplies electricity to the ECM even when the engine switch is off. This power allows the ECM to store data such as DTC history and freeze frame data. If the battery voltage falls below a minimum level, the stored ECM data will be cleared and the ECM will determine that there is a malfunction in the power supply circuit. The next time the engine is started, the ECM will illuminate the MIL and store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P056014 System Voltage Circuit Short to Ground or Open ECM back-up power source circuit voltage is low for 3 seconds or more (1-trip detection logic).

  • Back-up power source circuit

  • Battery terminals

  • Battery

  • ECM

 Comes on DTC stored

SAE Code:

P0562

Tech Tips

If DTC P056014 is stored, the ECM will not store other DTCs.

CONFIRMATION DRIVING PATTERN

Tech Tips

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG) and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the engine switch off and wait for 2 minutes or more.

  5. Turn the engine switch on (IG) and turn the GTS on.

  6. Wait for 3 seconds or more with the engine switch on (IG).

  7. Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

  8. Input the DTC: P056014.

  9. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.

WIRING DIAGRAM

B006KN6E02
*a MAIN
*b EFI-MAIN
*c EFI NO. 1
*d Battery

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

    Click here

PROCEDURE


  1. INSPECT BATTERY


    1. Check that the battery is not depleted.

      Click here

      OK
      Battery is not depleted.
      Result
      Proceed to
      OK
      NG

    NG

    CHARGE OR REPLACE BATTERY

    OK

  2. CHECK BATTERY TERMINAL


    1. Check that the battery terminals are not loose or corroded.

      OK
      Battery terminals are not loose or corroded.
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE BATTERY TERMINAL

    OK

  3. CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)


    1. B006L3AC03
      *a

      Front view of wire harness connector

      (to ECM)

      Disconnect the A53 ECM connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A53-1 (BATT) - Body ground Always 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ECM)

    OK

  4. CHECK WHETHER DTC OUTPUT RECURS (DTC P056014)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs.


      Powertrain > Transmission > Clear DTCs

    5. Turn the engine switch off and wait for at least 30 seconds.

    6. Turn the engine switch on (IG).

    7. Turn the GTS on.

    8. Wait 5 seconds or more.

    9. Enter the following menus: Powertrain / Transmission / Trouble Codes.


      Powertrain > Transmission > Trouble Codes

    10. Read the DTCs.

      Result
      Result Proceed to
      DTC P056014 is output A
      DTCs are not output B

    B

    CHECK FOR INTERMITTENT PROBLEMS Click here

    A

  5. REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    PERFORM REGISTRATION Click here