TRANSMISSION CONTROL CABLE ADJUSTMENT

PROCEDURE


  1. SECURE VEHICLE


    1. Fully apply the parking brake and chock a wheel.

      CAUTION:


      • Make sure to apply the parking brake and chock a wheel before performing this procedure.

      • If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.

      B006Q5R

  2. REMOVE CONSOLE BOX ASSEMBLY (for Integrated Type)

    Click here

  3. REMOVE CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL (for Separate Console Box Type)

    Click here

  4. REMOVE CENTER NO. 2 INSTRUMENT CLUSTER FINISH PANEL (for Separate Console Box Type)

    Click here

  5. REMOVE INSTRUMENT PANEL BOX ASSEMBLY (for Separate Console Box Type)

    Click here

  6. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for Separate Console Box Type)

    Click here

  7. ADJUST SHIFT LEVER POSITION


    1. Move the shift lever to N.

    2. B006KUV

      Disconnect the transmission control cable assembly from the shift lever assembly.

    3. B006L6EC01
      *a Stopper

      Using a screwdriver, pull out the stopper of the transmission control cable assembly.

      Note

      Do not remove the stopper. If it is removed, reinstall it to its original position.

    4. B006MZ6C01
      *a Stopper
      *b Nut
      *c Turn approximately 180°

      Turn the nut approximately 180° counterclockwise and, while holding the nut in that position, separate the transmission control cable assembly from the shift lock control unit assembly.

      Note

      Do not turn the nut excessively as the internal spring may come off and transmission control cable assembly will not be reusable.

    5. Push the 2 claws together at the top of the lock piece. While holding the 2 claws together, push the 2 lugs on the bottom of the lock piece toward each other and upward to push up the lock piece.

      B006OI9C10
      *a Bottom View *b Push
      *c Push out *d Lock Piece

    6. Turn the nut of the transmission control cable assembly 180° counterclockwise. While holding the nut in place, push in the stopper until it clicks twice.

      B006QNFC01
      *a Nut *b Turn approximately 180°
      *c Stopper *d Push in

      Note

      If the stopper cannot be pushed in, slightly turn the nut clockwise and then push in the stopper again.

    7. Connect the transmission control cable assembly to the shift lever assembly. Check that the spring is positioned at (A) and push in the stopper.

      B006NRWC01
      *1 Shift Lever Assembly - -
      *a Spring *b Push in
      *c Stopper *d Nut

      Note


      • If the stopper cannot be pushed in, slightly turn the nut clockwise and then push in the stopper again.

      • Make sure that the transmission control cable assembly is securely locked.

    8. B006MSLC01
      *a Pin
      *b Lock Piece

      Connect the transmission control cable assembly to the shift lever assembly.

      Note


      • The shift lever should be in N.

      • Connect the transmission control cable assembly all the way to the base of the pin.

      • Check that the lock piece is pulled up.

      • Connect the transmission control cable assembly so that the lock piece faces the passenger side.

    9. B006R7LC03
      *a Push in
      *b Lock Piece
      *c Adjuster Case

      Push the lock piece into the adjuster case.

      Note


      • Check that the park/neutral position switch assembly and shift lever are in neutral.

      • Securely push in the lock piece until the slider lock is engaged.

    10. After adjusting the shift lever position, check the operation and function of the shift lever. If there is a problem, adjust the position again.

  8. INSTALL CONSOLE BOX ASSEMBLY (for Integrated Type)

    Click here

  9. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for Separate Console Box Type)

    Click here

  10. INSTALL INSTRUMENT PANEL BOX ASSEMBLY (for Separate Console Box Type)

    Click here

  11. INSTALL CENTER NO. 2 INSTRUMENT CLUSTER FINISH PANEL (for Separate Console Box Type)

    Click here

  12. INSTALL CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL (for Separate Console Box Type)

    Click here