Tech Tips
Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
Inspect the fuses and relays related to this system before inspecting the suspected areas below.
| Symptom | Suspected Area | Link |
|---|---|---|
| Stop and start system does not operate | Stop and start system operation prohibition based on the battery conditions (Refer to [Stop and Start System does not Operate (Battery Condition)]) | |
| Engine hood courtesy switch circuit | ||
| Driver door courtesy switch circuit (system prohibits control) | ||
| Driver door courtesy switch circuit (CAN communication DTC U014087) | ||
| Driver door courtesy switch circuit | ||
| Driver seat belt buckle switch circuit (system prohibits control) | ||
| Driver seat belt buckle switch circuit (CAN communication DTC U014087) | ||
| Front seat inner belt assembly LH | ||
| Front seat inner belt assembly RH | ||
| Air conditioning system (system prohibits control) | ||
| Air conditioning system | ||
| Brake booster vacuum is low (system prohibits control) | ||
| Brake booster vacuum is low | ||
| Backup boost converter circuit | ||
| Park/Neutral position switch assembly circuit | ||
| Starter signal circuit | ||
| STA signal circuit | ||
| Starter inrush current reduction relay circuit | ||
| Crankshaft position sensor | ||
| ECM | ||
| Vacuum sensor | ||
| Brake booster assembly (for RHD) | ||
| Brake booster assembly (for LHD) | ||
| Oil pump with solenoid assembly | ||
| Starter assembly | ||
| The deceleration sensor zero point calibration is performed | ||
| Deceleration sensor (airbag ECU assembly) (w/ Navigation system) | ||
| Deceleration sensor (airbag ECU assembly) (w/o Navigation system) | ||
| Skid control ECU (brake actuator assembly) | ||
| CAN communication system (for RHD) | ||
| CAN communication system (for LHD) | ||
| Engine stop and start ECU | ||
| Battery*1 | ||
| Wire harness or connector | - | |
| Starter assembly does not operate | Battery | |
| Starter assembly | ||
| Park/Neutral position switch assembly | ||
| Smart entry and start system (for start function) | ||
| Starter signal circuit (SFI system) | ||
| Starter signal circuit | ||
| Cranking speed decreases | Battery | |
| Starter inrush current reduction relay circuit | ||
| Starter assembly | ||
| Stop and start cancel indicator does not operate | Combination meter assembly | |
| Indicator circuit (CAN communication system for RHD) | ||
| Indicator circuit (CAN communication system for LHD) | ||
| Engine stop and start ECU | ||
| Stop and start indicator does not operate | Combination meter assembly | |
| Indicator circuit (CAN communication system for RHD) | ||
| Indicator circuit (CAN communication system for LHD) | ||
| Engine stop and start ECU | ||
| Stop and start control cannot be canceled | ECAN terminal voltage | |
| Stop and start cancel switch circuit | ||
| Engine not stopped by stop and start control (stop and start operation prohibited) | Engine hood courtesy switch circuit | |
| Driver side door courtesy switch circuit | ||
| Stop light switch assembly | ||
| Engine stop and start ECU | ||
| Multi-information display screen does not change after pressing steering pad switch assembly | Stop and start priority control system | |
| Multi-information display screen changes without pressing steering pad switch assembly | Stop and start priority control system | |
| When the stop and start system cancel switch (combination switch assembly) is pressed and held, control does not change | Stop and start priority control system | |
| Even though the stop and start system cancel switch (combination switch assembly) and steering pad switch assembly are operated, the multi-information display screen does not change, and control does not change | Stop and start priority control system | |
| The control mode changes but Multi-information display screen is not displayed | Stop and start priority control system | |
| The control mode does not change but an interruption message is displayed in the combination meter assembly | Stop and start priority control system | |
| Control mode returns to default mode after turning engine switch on (IG) | Stop and start priority control system |
*1: If the vehicle has not been used for a long time, the battery charge may be low and stop and start control operation may be prohibited. In this case, recharge the battery, initialize the integrated current value*2 and drive the vehicle approximately 5 to 40 minutes until stop and start control operation is permitted.
*2: Use the GTS to perform Integrated Current Value Initialization.
Tech Tips
If the Data List item [Integrated Current] is 0 or more, it is not necessary to perform initialization.