ENGINE ASSEMBLY COMPONENTS
ILLUSTRATION
| *1 | NO. 1 ENGINE UNDER COVER | *2 | NO. 2 ENGINE UNDER COVER |
| *3 | REAR ENGINE UNDER COVER LH | *4 | REAR ENGINE UNDER COVER RH |
| *5 | FRONT LOWER BUMPER ABSORBER | - | - |
ILLUSTRATION
| *1 | RADIATOR RESERVE TANK ASSEMBLY | *2 | RADIATOR RESERVE TANK BRACKET |
| *3 | NO. 1 FUEL PIPE CLAMP SUB-ASSEMBLY | *4 | NO. 1 FUEL PIPE CLAMP |
| *5 | NO. 2 ENGINE MOUNTING STAY RH | *6 | NO. 1 FUEL VAPOR FEED HOSE |
| *7 | NO. 2 RADIATOR HOSE | *8 | UNION TO CONNECTOR TUBE HOSE |
| *9 | NO. 1 RADIATOR HOSE | *10 | HEATER WATER HOSE |
| *11 | OIL COOLER HOSE | *12 | NO. 2 FUEL PIPE CLAMP |
| *13 | ECM | *14 | NO. 1 WATER BY-PASS HOSE |
| *15 | NO. 2 WATER BY-PASS HOSE | *16 | FUEL PIPE |
| *17 | V-RIBBED BELT | *18 | V-BANK COVER SUB-ASSEMBLY |
| *19 | TRANSMISSION CONTROL CABLE ASSEMBLY | *20 | NO. 1 RELAY BLOCK COVER |
| *21 | ENGINE ROOM RELAY BLOCK ASSEMBLY | *22 | ENGINE WIRE |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | FRONT ENGINE MOUNTING INSULATOR | *2 | REAR ENGINE MOUNTING INSULATOR |
| *3 | COLUMN HOLE COVER SILENCER SHEET | *4 | NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY |
| *5 | NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY | *6 | FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY |
| *7 | FRONT SUSPENSION MEMBER BRACE SUB-ASSEMBLY LH | *8 | FRONT SUSPENSION MEMBER BRACE SUB-ASSEMBLY RH |
| *9 | FRONT SUSPENSION MEMBER REINFORCEMENT LH | *10 | FRONT SUSPENSION MEMBER REINFORCEMENT RH |
| *11 | FRONT CROSSMEMBER SUB-ASSEMBLY | - | - |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | - | - |
ILLUSTRATION
| *1 | ENGINE ASSEMBLY WITH TRANSAXLE | *2 | WIRE HARNESS BRACKET |
| *3 | MANIFOLD STAY | *4 | ENGINE WIRE |
| *5 | ENGINE MOUNTING INSULATOR LH | *6 | ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH |
| *7 | FRONT ENGINE MOUNTING BRACKET | *8 | DRIVE SHAFT BEARING BRACKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT | *2 | FRONT DRIVE PLATE SPACER |
| *3 | BRACKET | *4 | DRIVE PLATE AND RING GEAR SUB-ASSEMBLY |
| *5 | REAR DRIVE PLATE SPACER | *6 | FLYWHEEL HOUSING UNDER COVER |
| *7 | GENERATOR ASSEMBLY | *8 | ENGINE WIRE |
| *9 | O-RING | *10 | STARTER ASSEMBLY |
| *11 | AUTOMATIC TRANSAXLE ASSEMBLY | *12 | NO. 1 COOLER REFRIGERANT SUCTION HOSE |
| *13 | COMPRESSOR AND MAGNETIC CLUTCH | *14 | NO. 1 COOLER REFRIGERANT DISCHARGE HOSE |
| *a | BLACK COLOR: x 1 SILVER COLOR: x 5 |
- | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part |  |
Adhesive 1324 |
 |
Compressor oil ND-OIL 8 or equivalent | ★ | Precoated part |