ENGINE UNIT COMPONENTS
ILLUSTRATION
| *1 | ENGINE COOLANT TEMPERATURE SENSOR | *2 | KNOCK CONTROL SENSOR WIRE |
| *3 | ENGINE OIL PRESSURE SWITCH ASSEMBLY | *4 | KNOCK CONTROL SENSOR |
| *5 | NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE | *6 | ENGINE OIL LEVEL DIPSTICK |
| *7 | NO. 2 TIMING GEAR COVER | *8 | O-RING |
| *9 | GASKET | *10 | ENGINE ASSEMBLY |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
Adhesive 1324 | ★ | Precoated part |
ILLUSTRATION
| *1 | EXHAUST MANIFOLD SUB-ASSEMBLY RH (TWC: Front Catalyst) | *2 | EXHAUST MANIFOLD TO HEAD GASKET |
| *3 | NO. 2 EXHAUST MANIFOLD HEAT INSULATOR | *4 | EXHAUST MANIFOLD SUB-ASSEMBLY LH (TWC: Front Catalyst) |
| *5 | IGNITION COIL ASSEMBLY | *6 | NO. 2 MANIFOLD STAY |
| *7 | NO. 1 VACUUM SWITCHING VALVE ASSEMBLY | *8 | WATER PUMP PULLEY |
| *9 | V-RIBBED BELT TENSIONER ASSEMBLY | *10 | NO. 2 IDLER PULLEY SUB-ASSEMBLY |
| *11 | EXHAUST MANIFOLD TO HEAD GASKET LH | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | for Bank 1 | - | - |
| *1 | CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY RH (for Exhaust Side of Bank 1) | *2 | CYLINDER HEAD COVER SEAL WASHER |
| *3 | SPARK PLUG | *4 | O-RING |
| *5 | VVT SENSOR (for Exhaust Side of Bank 1) | *6 | CYLINDER HEAD COVER SUB-ASSEMBLY |
| *7 | CYLINDER HEAD COVER GASKET | *8 | GASKET |
| *9 | OIL PIPE UNION | *10 | OIL PIPE |
| *11 | OIL CONTROL VALVE FILTER RH | *12 | SPARK PLUG TUBE GASKET |
| *13 | CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY RH (for Intake Side of Bank 1) | *14 | VVT SENSOR (for Intake Side of Bank 1) |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
Adhesive 1324 | ★ | Precoated part |
ILLUSTRATION
| *A | for Bank 2 | - | - |
| *1 | CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY LH (for Exhaust Side of Bank 2) | *2 | CYLINDER HEAD COVER SEAL WASHER |
| *3 | SPARK PLUG | *4 | O-RING |
| *5 | VVT SENSOR (for Exhaust Side of Bank 2) | *6 | CYLINDER HEAD COVER SUB-ASSEMBLY LH |
| *7 | NO. 2 CYLINDER HEAD COVER GASKET | *8 | GASKET |
| *9 | OIL PIPE UNION | *10 | NO. 1 OIL PIPE |
| *11 | OIL CONTROL VALVE FILTER LH | *12 | VENTILATION VALVE SUB-ASSEMBLY |
| *13 | OIL FILLER CAP SUB-ASSEMBLY | *14 | OIL FILLER CAP GASKET |
| *15 | SPARK PLUG TUBE GASKET | *16 | CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY LH (for Intake Side of Bank 2) |
| *17 | VVT SENSOR (for Intake Side of Bank 2) | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
Adhesive 1324 | ★ | Precoated part |
ILLUSTRATION
| *A | w/ Taper Screw Plug | *B | w/o Taper Screw Plug |
| *1 | FRONT NO. 1 ENGINE MOUNTING BRACKET LH | *2 | WATER OUTLET GASKET |
| *3 | WATER OUTLET | *4 | O-RING |
| *5 | CYLINDER BLOCK WATER DRAIN COCK PLUG | *6 | CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY |
| *7 | ENGINE OIL LEVEL DIPSTICK GUIDE | *8 | CRANKSHAFT POSITION SENSOR |
| *9 | DRAIN COCK ASSEMBLY | *10 | WATER INLET HOUSING |
| *11 | NO. 2 WATER INLET HOUSING GASKET | *12 | GASKET |
| *13 | THERMOSTAT | *14 | WATER INLET |
| *15 | REAR ENGINE OIL SEAL | *16 | REAR ENGINE OIL SEAL RETAINER |
| *17 | TAPER SCREW PLUG | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
Adhesive 1324 | ★ | Precoated part |
ILLUSTRATION
| *1 | NO. 1 OIL PAN BAFFLE PLATE | *2 | NO. 2 OIL PAN SUB-ASSEMBLY |
| *3 | OIL FILTER CAP ASSEMBLY | *4 | OIL PAN DRAIN PLUG |
| *5 | OIL PAN SUB-ASSEMBLY | *6 | OIL STRAINER SUB-ASSEMBLY |
| *7 | OIL FILTER ELEMENT | *8 | OIL PAN DRAIN PLUG GASKET |
| *9 | DRAIN PLUG | *10 | GASKET |
| *11 | O-RING | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | Type A | *B | Type B |
| *1 | CRANKSHAFT PULLEY | *2 | ENGINE WATER PUMP ASSEMBLY |
| *3 | TIMING CHAIN CASE OIL SEAL | *4 | TIMING CHAIN COVER SUB-ASSEMBLY |
| *5 | TIMING CHAIN COVER PLATE | *6 | TIMING CHAIN COVER PLATE GASKET |
| *7 | WATER PUMP GASKET | *8 | CRANKSHAFT PULLEY SET BOLT |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
Adhesive 1344 |  |
MP grease |
 |
Do not apply lubricants to the threaded parts | ★ | Precoated part |
ILLUSTRATION
| *1 | CHAIN SUB-ASSEMBLY | *2 | CHAIN TENSIONER SLIPPER |
| *3 | CRANKSHAFT TIMING SPROCKET | *4 | IDLE SPROCKET ASSEMBLY |
| *5 | NO. 1 CHAIN TENSIONER ASSEMBLY | *6 | NO. 1 CHAIN VIBRATION DAMPER |
| *7 | NO. 2 CHAIN VIBRATION DAMPER | *8 | NO. 1 IDLE GEAR SHAFT |
| *9 | NO. 2 IDLE GEAR SHAFT | *10 | GASKET |
| *11 | PULLEY SET KEY | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | for Bank 1 | - | - |
| *1 | CAMSHAFT | *2 | CAMSHAFT BEARING CAP |
| *3 | CAMSHAFT HOUSING SUB-ASSEMBLY RH | *4 | NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
| *5 | NO. 2 CAMSHAFT | *6 | NO. 2 CHAIN TENSIONER ASSEMBLY |
| *7 | VALVE LASH ADJUSTER ASSEMBLY | *8 | VALVE STEM CAP |
| *9 | NO. 2 CHAIN SUB-ASSEMBLY | *10 | CAMSHAFT TIMING GEAR ASSEMBLY |
| *11 | CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY | *12 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| *T1 | 1st: 10 (102, 7) 2nd: 16 (163, 12) |
- | - |
ILLUSTRATION
| *A | for Bank 2 | - | - |
| *1 | CAMSHAFT BEARING CAP | *2 | CAMSHAFT HOUSING SUB-ASSEMBLY LH |
| *3 | NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY | *4 | NO. 3 CAMSHAFT SUB-ASSEMBLY |
| *5 | NO. 3 CHAIN TENSIONER ASSEMBLY | *6 | NO. 4 CAMSHAFT SUB-ASSEMBLY |
| *7 | VALVE LASH ADJUSTER ASSEMBLY | *8 | VALVE STEM CAP |
| *9 | NO. 2 CHAIN SUB-ASSEMBLY | *10 | CAMSHAFT TIMING GEAR ASSEMBLY |
| *11 | CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY | *12 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| *T1 | 1st: 10 (102, 7) 2nd: 16 (163, 12) |
- | - |
ILLUSTRATION
| *1 | CYLINDER HEAD SUB-ASSEMBLY | *2 | CYLINDER HEAD GASKET |
| *3 | CYLINDER HEAD LH | *4 | NO. 2 CYLINDER HEAD GASKET |
| *5 | PLATE WASHER | *6 | CYLINDER HEAD SET BOLT |
| *7 | NO. 1 WATER BY-PASS HOSE | *8 | WATER INLET PIPE |
| *9 | CYLINDER BLOCK SUB-ASSEMBLY | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| *T1 | 1st: 36 (367, 27) 2nd: Turn 90° 3rd: Turn 90° |
- | - |