OUTER REAR VIEW MIRROR GLASS INSPECTION

PROCEDURE


  1. INSPECT OUTER MIRROR LH


    1. B0058I0C01
      *a

      Component without harness connected

      (Outer Mirror LH)

      w/ Mirror Heater:

      Check the outer mirror heater operation.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        1 - 2 25°C (77°F) 6.8 to 10.2 Ω

        If the result is not as specified, replace the outer mirror LH.

    2. w/ EC Mirror:

      Check EC mirror operation.


      1. Connect a new 1.5 V dry-cell battery.

      2. B005ABEC01
        *a

        Component without harness connected

        (Outer Mirror LH)

        Apply 1.5 V dry-cell battery to the terminals of the connector, and check that the EC mirror operation.

        Note

        Do not apply a voltage of higher than 1.5 V.

        OK
        Tester Connection Specified Condition

        Positive (+) end of the 1.5 V dry-cell battery → 4

        Negative (-) end of the 1.5 V dry-cell battery → 1

        		 Mirror surface becomes dark

        If the result is not as specified, replace the outer mirror LH.

    3. w/ Blind Spot Monitor System:

      Check the operation of the blind spot monitor indicator.


      1. B005ABEC06
        *a

        Component without harness connected

        (Outer Mirror LH)

        Connect 4 new 1.5 V dry-cell batteries in series.

      2. Apply 6 V dry-cell batteries to the terminals of the connector, and check the blind spot monitor indicator condition.

        OK
        Tester Connection Specified Condition

        Positive (+) end of the 6 V dry-cell battery → 3

        Negative (-) end of the 6 V dry-cell battery → 2

        		 Blind spot monitor indicator comes on

        If the result is not as specified, replace the outer mirror LH.

  2. INSPECT OUTER MIRROR RH


    1. B005AGXC01
      *a

      Component without harness connected

      (Outer Mirror RH)

      w/ Mirror Heater:

      Check the outer mirror heater operation.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        1 - 2 25°C (77°F) 6.8 to 10.2 Ω

        If the result is not as specified, replace the outer mirror RH.

    2. w/ EC Mirror:

      Check EC mirror operation.


      1. Connect a new 1.5 V dry-cell battery.

      2. B0057EOC01
        *a

        Component without harness connected

        (Outer Mirror RH)

        Apply 1.5 V dry-cell battery voltage to the terminals of the connector, and check that the EC mirror operation.

        Note

        Do not apply a voltage of higher than 1.5 V.

        OK
        Tester Connection Specified Condition

        Positive (+) end of the 1.5 V dry-cell battery → 4

        Negative (-) end of the 1.5 V dry-cell battery → 1

        		 Mirror surface becomes dark

        If the result is not as specified, replace the outer mirror RH.

    3. w/ Blind Spot Monitor System:

      Check the operation of the blind spot monitor indicator.


      1. B0057EOC06
        *a

        Component without harness connected

        (Outer Mirror RH)

        Connect 4 new 1.5 V dry-cell batteries in series.

      2. Apply 6 V dry-cell batteries to the terminals of the connector, and check the blind spot monitor indicator condition.

        OK
        Tester Connection Specified Condition

        Positive (+) end of the 6 V dry-cell battery → 3

        Negative (-) end of the 6 V dry-cell battery → 2

        		 Blind spot monitor indicator comes on

        If the result is not as specified, replace the outer mirror RH.