POWER BACK DOOR SYSTEM CUSTOMIZE PARAMETERS


  1. CUSTOMIZE POWER BACK DOOR SYSTEM

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Record the current settings before customizing.


    1. Customizing with the GTS.


      1. Turn the engine switch off.

      2. Connect the GTS to the DLC3.

      3. Turn the enigne switch on (IG).

      4. Turn the GTS on.

      5. Enter the following menus: Customize Setting / PSD & PBD operation.

      6. Select the setting by referring to the table below.


        PSD & PBD operation
        Tester Display Description Default Setting ECU
        PBD SW Operation Function that turns the back door control switch on when a switch is pushed once or held down for 0.8 seconds. 0.8s 0:0.0s,1:0.8s Multiplex network door ECU
        PBD Buzzer Power back door warning buzzer operation condition signal OFF 0:OFF,1:ON Multiplex network door ECU
        Door Unlock with 1 Motion. Function that selects the door or doors to unlock when the back door is locked and the transmitter switch (electrical key transmitter sub-assembly) is pushed to operate the power back door.*1 ALL DOORS 0:BackDoor,1:ALL DOORS Multiplex network door ECU
        Wireless Power Back Door Open Function that operates the power back door by pushing the transmitter switch (electrical key transmitter sub-assembly).*2 Lock:0.8s/Unlock:0.8s 0000:"Lock:OFF/Unlock:OFF",0001:"Lock:OFF/Unlock:ON",0010:"Lock:OFF/Unlock:Twice",0011:"Lock:OFF/Unlock:0.8s",1010:"Lock:Twice/Unlock:Twice",1011:"Lock:0.8s/Unl**cut** Multiplex network door ECU
        PBD Assist Open Operation Function that enables or disables the power back door assist open operation. When PBD Assist Open is set to on (enabled) the back door will open automatically when the back door opener switch assembly (opener switch) is operated. ON 0:OFF,1:ON Multiplex network door ECU
        PBD Assist Close Operation Function that enables or disables the power back door assist close operation. When PBD Assist Close is set to on (enabled) the back door will open automatically when the back door control switch is operated. ON 0:OFF,1:ON Multiplex network door ECU
        Power Back Door Opening Adjust Function that can be used to set the power back door opening angle at 5 different positions. 5:Max 000:"1:Min",001:"2:Small",010:"3:Middle",011:"4:Large",100:"5:Max" Multiplex network door ECU

        • *1: "BackDoor" is only available for vehicles with the wireless one motion function.

        • *2: "Lock:Twice/Unlock:Twice" and "Lock:0.8s/Unlock:0.8s" are only available for vehicles with the wireless one motion function.

        • **cut**: ock: 0.8s

    2. Customizing with the Multi-display


      1. Turn the engine switch on (IG).

      2. Enter the following menus: Setup / Vehicle / Vehicle Customization / Other Vehicle Settings.

      3. Select the setting by referring to the table below.

        Display Description Default Setting ECU
        Power back door opening adjust Function that can be used to set the power back door opening angle at 5 different positions. 5 5, 4, 3, 2 or 1 Multiplex network door ECU

    3. Customizing with the combination meter assembly


      1. Turn the engine switch on (IG).

      2. Enter the following menus: Settings.

      3. Select the setting by referring to the table below.

        Display Description Default Setting Relevant ECU
        Power Back Door Function Function that enables or disables the power back door operation. ON ON or OFF Multiplex network door ECU