SLIDING ROOF SYSTEM Sliding Roof does not Move by Operating Sliding Roof Control Switch

DESCRIPTION

The sliding roof drive gear sub-assembly (sliding roof ECU) receives each signal when the map light assembly (slide roof switch) is operated and drives its built-in motor.

WIRING DIAGRAM

B005BD9E02

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • If the sliding roof drive gear sub-assembly (sliding roof ECU) is replaced, the sliding roof drive gear sub-assembly (sliding roof ECU) must be initialized.

    Click here

  • The sliding roof system uses the CAN and LIN communication systems. First, confirm that there are no malfunctions in the CAN and LIN communication systems. Refer to How to Proceed with Troubleshooting.

    Click here

  • If a sliding roof ECU (sliding roof drive gear sub-assembly) DTC is output, first perform troubleshooting for the sliding roof ECU (sliding roof drive gear sub-assembly) DTC.

    Click here

PROCEDURE


  1. PERFORM ACTIVE TEST USING GTS (Slide Roof)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Slide Roof / Active Test.

    5. Perform the Active Test according to the display on the GTS.


      Body Electrical > Sliding Roof > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Slide Roof Operate sliding roof motor OFF / Opn/Dwn / Clos/Up -

      Body Electrical > Sliding Roof > Active Test
      Tester Display
      Slide Roof
      OK
      Slide roof is operated using GTS.
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY Click here

    NG

  2. READ VALUE USING GTS (Open Switch, Close Switch, Up Switch, Down Switch)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Sliding Roof / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Sliding Roof > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Open Switch OPEN switch signal OFF or ON

      OFF: OPEN switch not pressed

      ON: OPEN switch pressed

      		 -
      Close Switch CLOSE switch signal OFF or ON

      OFF: CLOSE switch not pressed

      ON: CLOSE switch pressed

      		 -
      Up Switch UP switch signal OFF or ON

      OFF: UP switch not pressed

      ON: UP switch pressed

      		 -
      Down Switch DOWN switch signal OFF or ON

      OFF: DOWN switch not pressed

      ON: DOWN switch pressed

      		 -

      Body Electrical > Sliding Roof > Data List
      Tester Display
      Open Switch
      Close Switch
      Up Switch
      Down Switch
      OK
      The GTS display changes according to switch operation as shown in the table.
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY Click here

    NG

  3. INSPECT MAP LIGHT SWITCH


    1. Remove the map light assembly (slide roof switch).

      Click here

    2. Inspect the map light assembly (slide roof switch).

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE MAP LIGHT ASSEMBLY Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY - BATTERY AND BODY GROUND)


    1. B00577ZC31
      *a

      Front view of wire harness connector

      (to Sliding Roof Drive Gear Sub-assembly)

      Disconnect the sliding roof drive gear sub-assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      T9-1 (IG) - Body ground Engine switch on (IG) 11 to 14 V
      T9-1 (IG) - Body ground Engine switch off Below 1 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T9-12 (E) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY - MAP LIGHT ASSEMBLY AND BODY GROUND)


    1. Disconnect the T9 sliding roof drive gear sub-assembly connector.

    2. Disconnect the T6 map light assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T9-4 (UP) - T6-23 (UP) Always Below 1 Ω
      T9-4 (UP) or T6-23 (UP) - Body ground Always 10 kΩ or higher
      T9-5 (CLS) - T6-12 (CLS) Always Below 1 Ω
      T9-5 (CLS) or T6-12 (CLS) - Body ground Always 10 kΩ or higher
      T9-6 (DWN) - T6-24 (DOWN) Always Below 1 Ω
      T9-6 (DWN) or T6-24 (DOWN) - Body ground Always 10 kΩ or higher
      T9-7 (OPN) - T6-11 (OPN) Always Below 1 Ω
      T9-7 (OPN) or T6-11 (OPN) - Body ground Always 10 kΩ or higher
      T9-12 (E) - Body ground Always Below 1 Ω
      T6-19 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR