SLIDING ROOF SYSTEM, Diagnostic DTC:B2342

DTC Code DTC Name
B2342 Switch Failure

DESCRIPTION

This DTC is stored when the sliding roof drive gear sub-assembly (sliding roof ECU) detects that the map light assembly (slide roof switch) is stuck for 30 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2342 Switch Failure sliding roof drive gear sub-assembly (sliding roof ECU) detects map light assembly (slide roof switch) is stuck for 30 seconds or more.

  • Sliding roof drive gear sub-assembly (sliding roof ECU)

  • Map light assembly (slide roof switch)

  • Harness or connector

WIRING DIAGRAM

B005AOQE02

CAUTION / NOTICE / HINT

Note


  • If the sliding roof drive gear sub-assembly (sliding roof ECU) is replaced, the sliding roof drive gear sub-assembly (sliding roof ECU) must be initialized.

    Click here

  • The sliding roof system uses the CAN and LIN communication systems. First, confirm that there are no malfunctions in the CAN and LIN communication systems. Refer to How to Proceed with Troubleshooting.

    Click here

PROCEDURE


  1. READ VALUE USING GTS (Switch Failure [Past])


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Sliding Roof / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Sliding Roof > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Open Switch Failure(Past) OPEN switch failure signal (Past) OFF or ON

      OFF: No OPEN switch failure signal (Past)

      ON: OPEN switch failure signal (Past)

      		 -
      Close Switch Failure(Past) CLOSE switch failure signal (Past) OFF or ON

      OFF: No CLOSE switch failure signal (Past)

      ON: CLOSE switch failure signal (Past)

      		 -
      Up Switch Failure(Past) UP switch failure signal (Past) OFF or ON

      OFF: No UP switch failure signal (Past)

      ON: UP switch failure signal (Past)

      		 -
      Down Switch Failure(Past) DOWN switch failure signal (Past) OFF or ON

      OFF: No DOWN switch failure signal (Past)

      ON: DOWN switch failure signal (Past)

      		 -
      Open Switch Failure(Current) OPEN switch failure signal (Current) OFF or ON

      OFF: No OPEN switch failure signal (Current)

      ON: OPEN switch failure signal (Current)

      		 -
      Close Switch Failure(Current) CLOSE switch failure signal (Current) OFF or ON

      OFF: No CLOSE switch failure signal (Current)

      ON: CLOSE switch failure signal (Current)

      		 -
      Up Switch Failure(Current) UP switch failure signal (Current) OFF or ON

      OFF: No UP switch failure signal (Current)

      ON: UP switch failure signal (Current)

      		 -
      Down Switch Failure(Current) DOWN switch failure signal (Current) OFF or ON

      OFF: No DOWN switch failure signal (Current)

      ON: DOWN switch failure signal (Current)

      		 -

      Body Electrical > Sliding Roof > Data List
      Tester Display
      Open Switch Failure(Past)
      Close Switch Failure(Past)
      Up Switch Failure(Past)
      Down Switch Failure(Past)
      Open Switch Failure(Current)
      Close Switch Failure(Current)
      Up Switch Failure(Current)
      Down Switch Failure(Current)
      OK
      OFF appears on the GTS screen.
      Result
      Result Proceed to
      All items are displayed "OFF" A
      In part or in whole item displayed "ON" B

    A

    REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY Click here

    B

  2. INSPECT MAP LIGHT ASSEMBLY


    1. Remove the map light assembly (slide roof switch).

      Click here

    2. Inspect the map light assembly (slide roof switch).

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE MAP LIGHT ASSEMBLY Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY - MAP LIGHT ASSEMBLY AND BODY GROUND)


    1. Disconnect the T9 sliding roof drive gear sub-assembly connector.

    2. Disconnect the T6 map light assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T9-4 (UP) - T6-23 (UP) Always Below 1 Ω
      T9-4 (UP) or T6-23 (UP) - Body ground Always 10 kΩ or higher
      T9-5 (CLS) - T6-12 (CLS) Always Below 1 Ω
      T9-5 (CLS) or T6-12 (CLS) - Body ground Always 10 kΩ or higher
      T9-6 (DWN) - T6-24 (DOWN) Always Below 1 Ω
      T9-6 (DWN) or T6-24 (DOWN) - Body ground Always 10 kΩ or higher
      T9-7 (OPN) - T6-11 (OPN) Always Below 1 Ω
      T9-7 (OPN) or T6-11 (OPN) - Body ground Always 10 kΩ or higher
      T9-12 (E) - Body ground Always Below 1 Ω
      T6-19 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR