LOWER INSTRUMENT PANEL REMOVAL

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. TABLE OF BOLT, SCREW AND CLIP

    Tech Tips

    All bolts, screws, and clips relevant to installing and removing the instrument panel are shown along with their alphabet code in the table below.

    B0059PBE01

  2. DISABLE AUTOAWAY/RETURN FUNCTION (for Power Tilt and Power Telescopic Steering Column)


    1. Disable the autoaway/return function by changing the customize parameter.

      Click here

      CAUTION:

      Record the current customize parameter setting (whether the autoaway/return function is enabled or disabled) in order to restore the current setting after finishing the operation.

      Tech Tips

      Performing the above operation causes the autoaway/return function to be disabled when the engine switch is turned off.

    2. Turn the engine switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column assembly.

    3. Turn the engine switch off.

  3. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

    Click here

  4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  5. REMOVE HEADLIGHT DIMMER SWITCH ASSEMBLY

    Click here

  6. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY

    Click here

  7. REMOVE CONSOLE BOX ASSEMBLY

    Click here

  8. REMOVE AIR CONDITIONING CONTROL ASSEMBLY


    1. B00575T

      Pull the air conditioning control assembly in the direction indicated by the arrows shown in the illustration to detach the 6 clips.

    2. Disconnect the connectors and remove the air conditioning control assembly.

  9. REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY


    1. B005BAG

      Place your hand as shown in the illustration, and then pull the center instrument panel register assembly in the direction indicated by the arrow shown in the illustration to detach the 4 clips and remove the center instrument panel register assembly.

  10. REMOVE CENTER HEATER TO REGISTER DUCT


    1. B005BCRC02
      *a Clip <C>

      Remove the 2 clips <C>.

    2. Detach the 2 claws and remove the center heater to register duct.

  11. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET

    Click here

  12. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. B005A55

      for LHD:


      1. Using moulding remover A, detach the 3 claws and guide.

      2. Disconnect the connector and remove the No. 2 instrument panel under cover sub-assembly.

    2. B0058WX

      for RHD:


      1. Using moulding remover A, detach the 2 claws and guide.

      2. Disconnect the connector and remove the No. 2 instrument panel under cover sub-assembly.

  13. REMOVE DOOR SCUFF PLATE ASSEMBLY LH

    Click here

  14. REMOVE DOOR SCUFF PLATE ASSEMBLY RH

    Click here

  15. REMOVE COWL SIDE TRIM BOARD LH

    Click here

  16. REMOVE COWL SIDE TRIM BOARD RH

    Click here

  17. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  18. REMOVE TELEMATICS TRANSCEIVER WITH BRACKET

    Click here

  19. REMOVE NO. 1 SPEAKER ASSEMBLY WITH BOX

    Click here

  20. REMOVE NO. 2 INSTRUMENT PANEL HOLE COVER (for RHD)


    1. B00581ZC02
      B0057KY Protective Tape

      Put protective tape around the No. 2 instrument panel hole cover.

    2. Using a screwdriver, detach the 2 claws and 2 guides and remove the No. 2 instrument panel hole cover.

      Tech Tips

      Tape the screwdriver tip before use.

  21. REMOVE INSTRUMENT PANEL HOLE COVER (for RHD)


    1. B00598MC02
      *a Screws <A> or <B>

      Remove the 2 screws <A> or <B> and instrument panel hole cover.

  22. REMOVE GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY


    1. B0057DK

      Detach the claw and remove the glove compartment door stopper sub-assembly.

  23. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. for LHD:


      1. Detach the clamps.

      2. Remove the 2 bolts <D>.

      3. Remove the 9 bolts <F> or <G>.

      4. Remove the screw <E>.

      5. Disconnect the connector and room temperature sensor.

      6. Detach the 2 claws and disconnect the DLC3.

      7. Detach the claw and 2 guides and disconnect the hood lock control lever sub-assembly and remove the lower instrument panel sub-assembly.

        B00576AC05
        *1 Hood Lock Control Lever Sub-assembly - -
        *a Bolt <D> *b Bolt <F> or <G>
        *c Screw <E> *d Connector
        *e Room Temperature Sensor *f DLC3
        *g Guide - -

    2. for RHD:


      1. Detach the clamps.

      2. Remove the 2 bolts <D>.

      3. Remove the 9 bolts <F> or <G>.

      4. Remove the screw <E>.

      5. Disconnect the connector and room temperature sensor.

      6. Detach the 2 claws and disconnect the DLC3.

      7. Detach the claw and 2 guides and disconnect the hood lock control lever sub-assembly and remove the lower instrument panel sub-assembly.

        B0058UQC05
        *a Bolt <D> *b Bolt <F> or <G>
        *c Screw <E> *d Connector
        *e Room Temperature Sensor *f DLC3
        *g Guide *8 Hood Lock Control Lever Sub-assembly