DATA LIST
Tech Tips
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note
In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Sliding Roof / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Open Switch | Open switch signal | ON or OFF | ON: Open switch pressed OFF: Open switch not pressed |
- |
| Close Switch | Close switch signal | ON or OFF | ON: Close switch pressed OFF: Close switch not pressed |
- |
| Front SW Auto Operation | Roof sunshade auto function | ON or OFF | Customization status displayed | - |
| Hall IC1 Pulse | Hall IC1 pulse output | Lo or Hi | Lo and Hi repeat during motor operation | Lo: Hall IC1 output is low Hi: Hall IC1 output is high |
| Hall IC1 Status | Status of Hall IC1 | Normal or Error | Normal: Hall IC1 normal Error: Hall IC1 not normal |
- |
| Hall IC2 Pulse | Hall IC2 pulse output | Lo or Hi | Lo and Hi repeat during motor operation | Lo: Hall IC2 output is low Hi: Hall IC2 output is high |
| Hall IC2 Status | Status of Hall IC2 | Normal or Error | Normal: Hall IC2 normal Error: Hall IC2 not normal |
- |
| Ignition (Direct Signal) | Engine switch signal | ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off |
"OFF" is also displayed for this item when the engine switch is on (ACC). |
| Ignition (MPX) | Engine switch signal (LIN signal) | ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off |
"OFF" is also displayed for this item when the engine switch is on (ACC). |
| Open Switch Failure(Past) | Open switch failure signal (Past) | ON or OFF | ON: Roof sunshade open signal failure (Past) OFF: No roof sunshade open signal failure (Past) |
- |
| Close Switch Failure(Past) | Close switch failure signal (Past) | ON or OFF | ON: Roof sunshade close signal failure (Past) OFF: No roof sunshade close signal failure (Past) |
- |
| Open Switch Failure(Current) | Open switch failure signal (Current) | ON or OFF | ON: Roof sunshade open signal failure (Current) OFF: No roof sunshade open signal failure (Current) |
- |
| Close Switch Failure(Current) | Close switch failure signal (Current) | ON or OFF | ON: Roof sunshade close signal failure (Current) OFF: No roof sunshade close signal failure (Current) |
- |
| Number of Trouble Codes | Number of DTCs | Min.: 0, Max.: 255 | Number of stored DTCs | - |
ACTIVE TEST
Tech Tips
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Sliding Roof / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Slide Roof | Operate roof sunshade | OFF / Opn/Dwn / Clos/Up | - |