ROOF HEADLINING REMOVAL

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE REAR SEAT ASSEMBLY (for Manual Seat)

    Click here

  4. REMOVE REAR SEAT ASSEMBLY (for Power Seat)

    Click here

  5. REMOVE TONNEAU COVER ASSEMBLY


    1. B005AGN

      Remove the tonneau cover assembly.

  6. REMOVE DECK BOARD ASSEMBLY


    1. B005BDY

      w/o Spare Tire, for Compact Size Spare Tire:

      Remove the deck board assembly.

    2. B0057YE

      for Full Size Spare Tire:

      Remove the deck board assembly.

  7. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY


    1. B0059B2

      w/o Spare Tire, for Compact Size Spare Tire:

      Remove the No. 3 deck board sub-assembly.

    2. B005AP7

      for Full Size Spare Tire:

      Remove the No. 3 deck board sub-assembly.

  8. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY


    1. B0058OY

      w/o Spare Tire, for Compact Size Spare Tire:

      Remove the No. 2 deck board sub-assembly.

    2. B00585Z

      for Full Size Spare Tire:

      Remove the No. 2 deck board sub-assembly.

  9. REMOVE REAR DECK FLOOR BOX (w/ Spare Tire)


    1. B0057DR

      for Compact Size Spare Tire:

      Remove the rear deck floor box.

    2. B00583H

      for Full Size Spare Tire:

      Remove the rear deck floor box.

  10. REMOVE SPARE TIRE (w/ Spare Tire)


    1. Remove the spare tire.

  11. REMOVE DECK FLOOR BOX LH (w/ Spare Tire)


    1. B005B8J

      Remove the 4 clips.

    2. Detach the 3 guides and remove the deck floor box LH.

  12. REMOVE DECK FLOOR BOX LH (w/o Spare Tire)


    1. B00588Y

      Remove the 2 clips.

    2. Detach the 4 guides and remove the deck floor box LH.

  13. REMOVE DECK FLOOR BOX RH (w/ Spare Tire)


    1. B0058L3

      Remove the 2 clips.

    2. Detach the 4 guides and remove the deck floor box RH.

  14. REMOVE DECK FLOOR BOX RH (w/o Spare Tire)


    1. B00575D

      Remove the 2 clips.

    2. Detach the 4 guides and remove the deck floor box RH.

  15. REMOVE NO. 1 TOOL BOX SUB-ASSEMBLY (w/ Spare Tire)


    1. B005BGK

      Remove the screw.

    2. Detach the 2 claws, clip and 5 guides and remove the No. 1 tool box sub-assembly.

  16. REMOVE NO. 1 TOOL BOX SUB-ASSEMBLY (w/o Spare Tire)


    1. B005AYZ

      Remove the screw.

    2. Detach the 4 claws, 2 clips and 4 guides and remove the No. 1 tool box sub-assembly.

  17. REMOVE NO. 2 TOOL BOX SUB-ASSEMBLY (w/ Spare Tire)


    1. B0057OQ

      Remove the screw.

    2. Detach the 2 clips and 4 guides and remove the No. 2 tool box sub-assembly.

  18. REMOVE NO. 2 TOOL BOX SUB-ASSEMBLY (w/o Spare Tire)


    1. B00577R

      Remove the screw.

    2. Detach the clip and 4 guides and remove the No. 2 tool box sub-assembly.

  19. REMOVE REAR FLOOR FINISH PLATE


    1. Detach the 4 claws and 4 clips and remove the rear floor finish plate.

      B0058QZC05
      *A w/ Spare Tire *B w/o Spare Tire

  20. REMOVE DOOR SCUFF PLATE ASSEMBLY LH


    1. B005A3FC05
      B0057KY Protective Tape

      Put protective tape around the door scuff plate assembly LH.

    2. B005AJZC05
      *a Claw A
      *b Claw B

      Detach the 2 claws and guide on the front side of the door scuff plate assembly LH in the order shown in the illustration.

      Tech Tips


      • Pull the door scuff plate assembly LH towards you in the direction indicated by the arrow in the illustration to detach claw A.

      • Pull the door scuff plate assembly LH upwards in the direction indicated by the arrow in the illustration to detach claw B.

    3. B0059GLC05
      *a Claw A
      *b Claw B

      Detach the 2 claws and guide on the rear side of the door scuff plate assembly LH in the order shown in the illustration.

      Tech Tips


      • Pull the door scuff plate assembly LH towards you in the direction indicated by the arrow in the illustration to detach claw A.

      • Pull the door scuff plate assembly LH upwards in the direction indicated by the arrow in the illustration to detach claw B.

    4. B0058E4

      Pull the door scuff plate assembly LH upwards in the direction indicated by the arrow in the illustration to detach the 6 claws and remove the door scuff plate assembly LH.

  21. REMOVE DOOR SCUFF PLATE ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  22. REMOVE COWL SIDE TRIM BOARD LH


    1. B0058O6

      Remove the cap nut.

    2. Detach the clip and remove the cowl side trim board LH.

  23. REMOVE COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure described for the LH side.

  24. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. B005APT

      Remove the front door opening trim weatherstrip LH.

  25. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  26. REMOVE REAR DOOR SCUFF PLATE LH


    1. B0058F9C04
      B0057KY Protective Tape

      Put protective tape around the rear door scuff plate LH.

    2. B005B08C04
      *a Claw A
      *b Claw B

      Detach the 2 claws and guide on the front side of the rear door scuff plate LH in the order shown in the illustration.

      Tech Tips


      • Pull the rear door scuff plate LH towards you in the direction indicated by the arrow in the illustration to detach claw A.

      • Pull the rear door scuff plate LH upwards in the direction indicated by the arrow in the illustration to detach claw B.

    3. B005A6SC04
      *a Claw A
      *b Claw B

      Detach the 2 claws and guide on the rear side of the rear door scuff plate LH in the order shown in the illustration.

      Tech Tips


      • Pull the rear door scuff plate LH towards you in the direction indicated by the arrow in the illustration to detach claw A.

      • Pull the rear door scuff plate LH upwards in the direction indicated by the arrow in the illustration to detach claw B.

    4. B005AG7

      Pull the rear door scuff plate LH upwards in the direction indicated by the arrow in the illustration to detach the 4 claws and remove the rear door scuff plate LH.

  27. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  28. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. B005AIV

      Remove the rear door opening trim weatherstrip LH.

  29. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  30. REMOVE FRONT PILLAR GARNISH ASSEMBLY LH


    1. B005BDQC02
      *1 Front Pillar Garnish Clip
      *a Place hand here

      Place your hand in the position shown in the illustration and pull the upper portion of the front pillar garnish assembly LH in the direction indicated by the arrow to detach the 2 front pillar garnish clips.

      Tech Tips

      Make the front pillar garnish assembly LH hang down from the front pillar garnish clip.

    2. Turn the end of the front pillar garnish clip 90° with needle-nose pliers and remove it from the front pillar garnish assembly LH.

      Tech Tips

      Tape the tips of the needle-nose pliers before use.

    3. Detach the 2 guides and remove the front pillar garnish assembly LH.

      B0059KBC04
      *1 Front Pillar Garnish Clip - -
      *a 90° - -
      B0057KY Protective Tape - -

    4. Using your fingers, grasp the parts indicated by the arrows shown in the illustration and remove the front pillar garnish clip.

      Note

      If the front pillar garnish clip is damaged, replace it with a new one.

      B0059A4

    5. When the front pillar garnish clip cannot be removed by using your fingers:


      1. B00576TN02

        While pressing the part indicated by the arrow shown in the illustration with your finger, lift the front pillar garnish clip in direction A.

      2. B0058L8N03

        While pulling in direction B, push the part indicated by the arrow shown in the illustration with the end of a screwdriver to remove the front pillar garnish clip.

        Note

        If the front pillar garnish clip is damaged, replace it with a new one.

    6. B0057KOC05
      *a Protective Cover
      B0057KY Adhesive Tape

      Protect the curtain shield airbag assembly LH.


      1. Completely cover the curtain shield airbag assembly LH with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

        Note

        Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish assembly LH is removed.

  31. REMOVE FRONT PILLAR GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  32. REMOVE OUTER LAP BELT ANCHOR COVER

    Tech Tips

    Use the same procedure for both outer lap belt anchor covers.


    1. B0059RA

      Detach the 2 claws and guide and remove the outer lap belt anchor cover.

  33. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. B005AG6

      Remove the bolt and disconnect the front seat outer belt assembly LH.

  34. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  35. REMOVE LOWER CENTER PILLAR GARNISH LH


    1. B005B3U

      Pull both sides of the lower center pillar garnish LH outward to detach the 2 claws.

    2. Detach the 4 clips and remove the lower center pillar garnish LH.

  36. REMOVE LOWER CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  37. REMOVE CENTER PILLAR GARNISH ASSEMBLY LH


    1. B0057BK

      Remove the 2 clips.

    2. Detach the clip.

    3. Pass the front seat outer belt floor anchor through the center pillar garnish assembly LH, and remove the center pillar garnish LH.

  38. REMOVE CENTER PILLAR GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  39. REMOVE NO. 3 BATTERY SERVICE COVER BOARD (for Power Seat)

    Click here

  40. REMOVE NO. 2 BATTERY SERVICE COVER BOARD (for Power Seat)

    Click here

  41. REMOVE UPPER DECK TRIM SIDE BOARD LH


    1. B005B5P

      Remove the bolt.

    2. Detach the 10 claws and guide and remove the upper deck trim side board LH.

  42. REMOVE UPPER DECK TRIM SIDE BOARD RH

    Tech Tips

    Use the same procedure described for the LH side.

  43. REMOVE ROPE HOOK ASSEMBLY

    Tech Tips

    Use the same procedure for both rope hook assemblies.


    1. B005BA8C04
      B0057KY Protective Tape

      Using a screwdriver, detach the 2 claws and open the cover.

      Tech Tips

      Tape the screwdriver tip before use.

    2. B00583I

      Remove the bolt and rope hook assembly.

  44. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY

    Tech Tips

    Use the same procedure for all luggage hold belt striker assemblies.


    1. B005A56

      Remove the bolt and luggage hold belt striker assembly.

  45. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    1. for LH Side:


      1. Using a screwdriver, push in the claw and turn the No. 1 luggage compartment trim hook in the direction indicated by the arrow shown in the illustration.

        Tech Tips

        Tape the screwdriver tip before use.

      2. Pull the No. 1 luggage compartment trim hook in the direction indicated by the arrow in the illustration to detach the claw and guide and remove the No. 1 luggage compartment trim hook.

        B0057ZOC04
        B0057KY Protective Tape - -

    2. for RH Side:


      1. Using a screwdriver, push in the claw and turn the No. 1 luggage compartment trim hook in the direction indicated by the arrow shown in the illustration.

        Tech Tips

        Tape the screwdriver tip before use.

      2. Pull the No. 1 luggage compartment trim hook in the direction indicated by the arrow in the illustration to detach the claw and guide and remove the No. 1 luggage compartment trim hook.

        B005AO7C04
        B0057KY Protective Tape - -

  46. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Detach the 5 claws, 2 clips and 2 guides.

    2. Disconnect the connectors and remove the deck trim side panel assembly LH.

      B0059JS

  47. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  48. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH


    1. B005A9L

      Detach the 7 clips and remove the inner roof side garnish assembly LH.

  49. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  50. REMOVE VISOR BRACKET COVER

    Tech Tips

    Use the same procedure for both visor bracket covers.


    1. B005AXM

      Using moulding remover A, detach the 4 claws and remove the visor bracket cover.

  51. REMOVE VISOR ASSEMBLY LH


    1. B0057EYC01
      *1 Visor Holder

      Disconnect the visor assembly LH from the visor holder.

    2. Remove the 2 screws and visor assembly LH.

  52. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  53. REMOVE VISOR HOLDER

    Tech Tips

    Use the same procedure for both visor holders.


    1. B005B6AN12

      Turn the visor holder clockwise approximately 45° and pull it out as shown in the illustration.

    2. Detach the 2 claws and remove the visor holder.

  54. REMOVE ASSIST GRIP SUB-ASSEMBLY

    Tech Tips

    Use the same procedure for both assist grip sub-assemblies.


    1. B0059IBC01
      *a Cutout

      Insert SST into the cutout of the assist grip cover LH as shown in the illustration.

      SST
      09813-00010

      Note

      To prevent the assist grip sub-assembly from being damaged, make sure to insert SST straight into the cutout.

    2. B005AQNC01
      *a 30 to 45°
      B0057RX Remove in this Direction

      Pull SST as shown in the illustration to detach the claw.

      Note

      To prevent the assist grip sub-assembly from being damaged, make sure to only pull SST as shown in the illustration.

      Tech Tips

      Use the same procedure for the claw on the other side of the assist grip cover LH.

    3. B0057QC

      Detach the 2 clips and remove the assist grip sub-assembly.

    4. Remove the remaining clip.

  55. REMOVE REAR ASSIST GRIP ASSEMBLY LH


    1. B005ADIC01
      *a Cutout

      Insert SST into the cutout of the assist grip cover LH as shown in the illustration.

      SST
      09813-00010

      Note

      To prevent the rear assist grip assembly LH from being damaged, make sure to insert SST straight into the cutout.

    2. B005BAXC01
      *a 30 to 45°
      B0057RX Remove in this Direction

      Pull SST as shown in the illustration to detach the claw.

      Note

      To prevent the rear assist grip assembly LH from being damaged, make sure to only pull SST as shown in the illustration.

      Tech Tips

      Use the same procedure for the claw on the other side of the assist grip cover LH.

    3. B00579V

      Detach the 2 clips and remove the rear assist grip assembly LH.

    4. Remove the remaining clip.

  56. REMOVE REAR ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  57. REMOVE MAP LIGHT ASSEMBLY

    Click here

  58. REMOVE SPOT LIGHT ASSEMBLY

    Click here

  59. REMOVE SEAT BELT ANCHOR COVER


    1. B005BAJ

      Detach the 2 claws, 3 clips and 2 guides and remove the seat belt anchor cover.

  60. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror, w/o Lane Departure Alert System)

    Click here

  61. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)

    Click here

  62. REMOVE NO. 2 FORWARD RECOGNITION COVER (w/ EC Mirror, w/ Lane Departure Alert System)

    Click here

  63. REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ EC Mirror, w/ Lane Departure Alert System)

    Click here

  64. REMOVE ROOF HEADLINING ASSEMBLY (for Normal Roof)


    1. B005AUM

      Disconnect the connectors and detach the clamps from the front pillar LH.

    2. B0057KS

      Disconnect the connectors and detach the clamps from the front pillar RH.

    3. for LHD:


      1. B0058SWC01
        *A w/ Rain Sensor

        w/ EC Mirror, w/o Lane Departure Alert System:

        Disconnect the connectors.

      2. B0057K0C01
        *A w/ Rain Sensor

        w/ EC Mirror, w/ Lane Departure Alert System:

        Disconnect the connectors.

    4. for RHD:


      1. B0057DXC01
        *A w/ Rain Sensor

        w/ EC Mirror, w/o Lane Departure Alert System:

        Disconnect the connectors.

      2. B00594PC01
        *A w/ Rain Sensor

        w/ EC Mirror, w/ Lane Departure Alert System:

        Disconnect the connectors.

    5. B005ATH

      Disconnect the connector from the rear pillar RH.

    6. for Type A:


      1. Detach the 3 clips.

        B0058EN
      2. B0059ZC

        Turn the roof headlining assembly diagonally and bend slightly to remove it from the back door.

        Note


        • Make sure wrinkles do not form in the roof headlining assembly during removal.

        • Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.

        • Do not damage the roof headlining assembly or vehicle interior.

    7. for Type B:


      1. Detach the 3 clips.

        B00588J
      2. B0059J4

        Turn the roof headlining assembly diagonally and bend slightly to remove it from the back door.

        Note


        • Make sure wrinkles do not form in the roof headlining assembly during removal.

        • Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.

        • Do not damage the roof headlining assembly or vehicle interior.

  65. REMOVE ROOF HEADLINING ASSEMBLY (for Sliding Roof)


    1. B005AUM

      Disconnect the connectors and detach the clamps from the front pillar LH.

    2. B0057KS

      Disconnect the connectors and detach the clamps from the front pillar RH.

    3. B005AZI

      Disconnect the drive gear connector.

    4. for LHD:


      1. B0058SWC02
        *A w/ Rain Senseor

        w/ EC Mirror, w/o Lane Departure Alert System:

        Disconnect the connectors.

      2. B0057K0C03
        *A w/ Rain Senseor

        w/ EC Mirror, w/ Lane Departure Alert System:

        Disconnect the connectors.

    5. for RHD:


      1. B0057DXC02
        *A w/ Rain Senseor

        w/ EC Mirror, w/o Lane Departure Alert System:

        Disconnect the connectors.

      2. B00594PC02
        *A w/ Rain Senseor

        w/ EC Mirror, w/ Lane Departure Alert System:

        Disconnect the connectors.

    6. B005ATH

      Disconnect the connector from the rear pillar RH.

    7. for Type A:


      1. Detach the 3 clips, 8 fasteners and guide.

        B005A8XC03
        *a Fastener *b Guide
      2. B005AZH

        Turn the roof headlining assembly diagonally and bend slightly to remove it from the back door.

        Note


        • Make sure wrinkles do not form in the roof headlining assembly during removal.

        • Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.

        • Do not damage the roof headlining assembly or vehicle interior.

    8. for Type B:


      1. Detach the 3 clips, 8 fasteners and guide.

        B005A6XC03
        *a Fastener *b Guide
      2. B00572K

        Turn the roof headlining assembly diagonally and bend slightly to remove it from the back door.

        Note


        • Make sure wrinkles do not form in the roof headlining assembly during removal.

        • Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.

        • Do not damage the roof headlining assembly or vehicle interior.

  66. REMOVE ROOF HEADLINING ASSEMBLY (for Glass Roof)


    1. B005AUM

      Disconnect the connectors and detach the clamps from the front pillar LH.

    2. B0057KS

      Disconnect the connectors and detach the clamps from the front pillar RH.

    3. for LHD:


      1. B0058SWC03
        *A w/ Rain Sensor

        w/ EC Mirror, w/o Lane Departure Alert System:

        Disconnect the connectors.

      2. B0057K0C02
        *A w/ Rain Sensor

        w/ EC Mirror, w/ Lane Departure Alert System:

        Disconnect the connectors.

    4. for RHD:


      1. B0057DXC03
        *A w/ Rain Sensor

        w/ EC Mirror, w/o Lane Departure Alert System:

        Disconnect the connectors.

      2. B00594PC03
        *A w/ Rain Sensor

        w/ EC Mirror, w/ Lane Departure Alert System:

        Disconnect the connectors.

    5. B005ATH

      Disconnect the connector from the rear pillar RH.

    6. Detach the 3 clips, 14 fasteners and guide.

      B0059HTC03
      *a Fastener *b Guide
    7. B0058K3

      Turn the roof headlining assembly diagonally and bend slightly to remove it from the back door.

      Note


      • Make sure wrinkles do not form in the roof headlining assembly during removal.

      • Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.

      • Do not damage the roof headlining assembly or vehicle interior.

  67. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH


    1. B005A3T

      Detach the 6 guides and remove the front shoulder belt anchor plate sub-assembly LH.

  68. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  69. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH

    Click here

  70. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  71. REMOVE REAR SIDE RAIL SPACER LH


    1. B0057Z2

      Remove the 2 bolts.

    2. Detach the claw and remove the rear side rail spacer LH.

  72. REMOVE REAR SIDE RAIL SPACER RH

    Tech Tips

    Use the same procedure described for the LH side.

  73. REMOVE REAR NO. 2 SIDE RAIL SPACER LH


    1. B00592H

      Remove the 2 bolts.

    2. Detach the 2 claws and remove the rear No. 2 side rail spacer LH.

  74. REMOVE REAR NO. 2 SIDE RAIL SPACER RH

    Tech Tips

    Use the same procedure described for the LH side.