REAR SEAT ASSEMBLY(for Manual Seat) REMOVAL

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

PROCEDURE


  1. REMOVE TONNEAU COVER ASSEMBLY

    Click here

  2. REMOVE DECK BOARD ASSEMBLY

    Click here

  3. REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY


    1. B005AHWC05
      *A w/ Seat Heater System
      *a Rear seat cushion lock hook section
      *b Hook section at rear of rear seat cushion frame

      Lift the front end of the rear seat cushion assembly as shown in the illustration and detach the 2 hooks from the rear seat cushion lock hook section.

      Note

      The rear seat cushion frame will deform if lifted at a position far from the rear seat cushion lock hook.

    2. Detach the 2 hooks of the rear of the rear seat cushion frame.

    3. Pass the rear seat inner with center belt assembly RH through the rubber band of the rear seat cushion assembly.

    4. w/ Seat Heater System:


      1. Slightly lift up the bench type rear seat cushion assembly and disconnect the 2 connectors under it.

        Note

        Be careful not to damage the connector or wire harness.

    5. Remove the bench type rear seat cushion assembly.

      Note

      Be careful not to damage the vehicle body.

  4. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH


    1. B0058FNC01
      *1 Protective Tape

      Using a screwdriver, detach the claw to remove the reclining adjuster release handle LH.

      Tech Tips

      Tape the screwdriver tip before use.

  5. REMOVE RECLINING ADJUSTER RELEASE HANDLE RH

    Tech Tips

    Use the same procedure described for the LH side.

  6. REMOVE REAR DOOR SCUFF PLATE LH

    Click here

  7. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  8. REMOVE NO. 3 BATTERY SERVICE COVER BOARD


    1. B0058DA

      Remove the 2 clips.

    2. Detach the 2 clips and guide to remove the No. 3 battery service cover board.

  9. REMOVE NO. 2 BATTERY SERVICE COVER BOARD

    Tech Tips

    Use the same procedure described for the No. 3 battery service cover board.

  10. REMOVE REAR SEATBACK ASSEMBLY LH


    1. Operate the reclining adjuster release handle to fold down the rear seatback assembly LH.

    2. B0058L6

      Using a clip remover, remove the 4 clips.

    3. Return the rear seatback assembly LH to the upright position.

    4. B005BCK

      Detach the 6 clamps to disconnect the rear seat reclining control cable.

    5. B0058IY

      w/ Seat Belt Warning System, w/o Seat Heater System:


      1. Disconnect the connector.

      2. Detach the 2 clamps to disconnect the wire harness.

    6. B00575V

      w/ Seat Heater System:


      1. Disconnect the connector.

      2. Detach the 3 clamps to disconnect the wire harness.

    7. B0059R6

      Remove the 4 bolts.

    8. Detach the 2 guides to remove the rear seatback assembly LH.

      Note

      Be careful not to damage the vehicle body.

  11. REMOVE REAR SEATBACK ASSEMBLY RH


    1. Operate the reclining adjuster release handle to fold down the rear seatback assembly RH.

    2. B0059YO

      Using a clip remover, remove the 3 clips.

    3. Return the rear seatback assembly RH to the upright position.

    4. B0058Y1

      Detach the 6 clamps to disconnect the rear seat reclining control cable.

    5. B00580Y

      w/ Seat Belt Warning System, w/o Seat Heater System:


      1. Disconnect the connector.

      2. Detach the 2 clamps to disconnect the wire harness.

    6. B005BGW

      w/ Seat Heater System:


      1. Disconnect the connector.

      2. Detach the 3 clamps to disconnect the wire harness.

    7. B005BGL

      Remove the 4 bolts.

    8. Detach the 2 guides to remove the rear seatback assembly LH.

      Note

      Be careful not to damage the vehicle body.

  12. REMOVE BATTERY SERVICE COVER BOARD


    1. B005776

      Remove the 5 clips.

    2. Detach the 2 guides to remove the battery service cover board.

  13. REMOVE NO. 1 SEAT LEG ASSEMBLY


    1. B0058A2

      w/ Seat Belt Warning System:

      Detach the 2 claws and 3 clamps to disconnect the wire harness.

    2. w/ Seat Heater System:

      Detach the 2 claws and 3 clamps to disconnect the wire harness.

    3. B0056YP

      Remove the 10 bolts.

    4. Detach the 2 guides to remove the No. 1 seat leg assembly.

  14. REMOVE SEAT LEG BRACKET


    1. Partially remove the floor carpet.

    2. B0057LX

      Detach the clamp.

    3. Remove the 4 bolts and seat leg bracket.