SEAT HEATER SYSTEM Seat Heater for Front Right Seat does not Operate

DESCRIPTION

When the seat heater switch on air conditioning control assembly is operated, the air conditioning amplifier assembly receives the signal. The air conditioning amplifier assembly receives the signal and operates the front seat heater.

WIRING DIAGRAM


  1. for L-Sport Seat Type


    1. for Power Seat:

      B005B8WE05
      B005B8WE03

    2. for Manual Seat:

      B005B8WE09
      B005B8WE10

  2. for F-Sport Seat Type

    B0059XIE05
    B0059XIE03

CAUTION / NOTICE / HINT

Note


  • If the battery voltage is low, the seat heater system may not operate. When "High Power Consumption / Partial Limit On AC/Heater Operation" is displayed on the multi-information display in the combination meter assembly, inspect the battery, referring to On-vehicle Inspection for the charging system.

    Tech Tips

    If the battery voltage is low, "Operation Limitation Control History Count (Level 1)" and "Operation Limitation Control History Count (Level 2) is counted.

    Click here


  • If the battery voltage is low, the seat heater system may not operate. Refer to Data List for the power steering system.


    • for Manual Tilt and Manual Telescopic Steering Column: Click here

    • for Power Tilt and Power Telescopic Steering Column: Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE


  1. READ VALUE USING GTS (FR Seat Heater Temperature)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Air Conditioner / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Air Conditioner > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      FR Seat Heater Temperature Front seat RH heater temperature -29.7°C to 59.55°C Within range from 32 to 43°C (89 to 109°F) Front seat heater is on

      Body Electrical > Air Conditioner > Data List
      Tester Display
      FR Seat Heater Temperature
      OK
      On the GTS screen, the seat heater temperature is as specified in the normal condition column.
      Result
      Result Proceed to
      OK A
      NG (for L-Sports Seat Type) B
      NG (for F-Sports Seat Type) C

    A

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

    C

    CHECK HARNESS AND CONNECTOR (FRONT SEAT CUSHION PAD WITH COVER RH - BATTERY AND BODY GROUND) Click here

    B

  2. CHECK HARNESS AND CONNECTOR (SEAT HEATER CONTROL SUB-ASSEMBLY RH - BATTERY AND BODY GROUND)


    1. B0059D1C29
      *A for Power Seat
      *B for Manual Seat
      *a

      Front view of wire harness connector

      (to Seat Heater Control Sub-assembly RH)

      Disconnect the seat heater control sub-assembly RH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for Power Seat
      Tester Connection Condition Specified Condition
      f9-6 (E) - Body ground Always Below 1 Ω
      for Manual Seat
      Tester Connection Condition Specified Condition
      P43-6 (E) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      for Power Seat
      Tester Connection Switch Condition Specified Condition
      f9-4 (IG) - Body ground Engine switch on (IG) 11 to 14 V
      f9-4 (IG) - Body ground Engine switch off Below 1 V
      for Manual Seat
      Tester Connection Switch Condition Specified Condition
      P43-4 (IG) - Body ground Engine switch on (IG) 11 to 14 V
      P43-4 (IG) - Body ground Engine switch off Below 1 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT SEAT HEATER CONTROL SUB-ASSEMBLY RH


    1. B005AM5C15
      *A for Power Seat
      *B for Manual Seat
      *a

      Seat Heater Control Sub-assembly RH

      (to Air Conditioning Amplifier Assembly)
      *b

      Seat Heater Control Sub-assembly RH

      (to Separate Type Front Seat Cushion Cover RH)

      Disconnect the f9 and SHR seat heater control sub-assembly RH connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for Power Seat
      Tester Connection Condition Specified Condition
      f9-5 (THR) - SHR-2 (TH1) Always Below 1 Ω
      f9-5 (THR) or SHR-2 (TH1) - Body ground Always 10 kΩ or higher
      f9-2 (PR) - SHR-3 (TH2) Always Below 1 Ω
      f9-2 (PR) or SHR-3 (TH2) - Body ground Always 10 kΩ or higher
      for Manual Seat
      Tester Connection Condition Specified Condition
      P43-5 (THR) - SHR-2 (TH1) Always Below 1 Ω
      P43-5 (THR) or SHR-2 (TH1) - Body ground Always 10 kΩ or higher
      P43-2 (PR) - SHR-3 (TH2) Always Below 1 Ω
      P43-2 (PR) or SHR-3 (TH2) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE SEAT HEATER CONTROL SUB-ASSEMBLY RH Click here

    OK

  4. INSPECT SEPARATE TYPE FRONT SEAT CUSHION COVER RH


    1. Remove the separate type front seat cushion cover RH.


    2. Inspect the separate type front seat cushion cover RH.


      Result
      Proceed to
      OK
      NG

    NG

    REPLACE SEPARATE TYPE FRONT SEAT CUSHION COVER RH for Manual Seat: Click here for Power Seat: Click here

    OK

  5. INSPECT SEPARATE TYPE FRONT SEATBACK COVER RH


    1. Remove the separate type front seatback cover RH.


    2. Inspect the separate type front seatback cover RH.


      Result
      Proceed to
      OK
      NG

    NG

    REPLACE SEPARATE TYPE FRONT SEATBACK COVER RH for Manual Seat: Click here for Power Seat: Click here

    OK

  6. CHECK SEAT HEATER CONTROL SUB-ASSEMBLY RH


    1. Temporarily replace the seat heater control sub-assembly RH with a new or known good one.

      Click here

    2. Check that the seat heater system is operated normally.

      OK
      The seat heater system is operated normally.
      Result
      Proceed to
      OK
      NG

    OK

    END (SEAT HEATER CONTROL SUB-ASSEMBLY RH WAS DEFECTIVE)

    NG

  7. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - SEAT HEATER CONTROL SUB-ASSEMBLY RH)


    1. Disconnect the I50 and I54 air conditioning amplifier assembly connectors.

    2. Disconnect the f9*1 or P43*2 seat heater control sub-assembly RH connector.


      • *1: for Power Seat

      • *2: for Manual Seat

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD (for Power Seat)
      Tester Connection Condition Specified Condition
      I50-16 (SHP+) - f9-1 (SWR) Always Below 1 Ω
      I50-16 (SHP+) or f9-1 (SWR) - Body ground Always 10 kΩ or higher
      I54-3 (TSR) - f9-5 (THR) Always Below 1 Ω
      I54-3 (TSR) or f9-5 (THR) - Body ground Always 10 kΩ or higher
      I54-7 (SG-3) - f9-2 (PR) Always Below 1 Ω
      I54-7 (SG-3) or f9-2 (PR) - Body ground Always 10 kΩ or higher
      for LHD (for Manual Seat)
      Tester Connection Condition Specified Condition
      I50-16 (SHP+) - P43-1 (SWR) Always Below 1 Ω
      I50-16 (SHP+) or P43-1 (SWR) - Body ground Always 10 kΩ or higher
      I54-3 (TSR) - P43-5 (THR) Always Below 1 Ω
      I54-3 (TSR) or P43-5 (THR) - Body ground Always 10 kΩ or higher
      I54-7 (SG-3) - P43-2 (PR) Always Below 1 Ω
      I54-7 (SG-3) or P43-2 (PR) - Body ground Always 10 kΩ or higher
      for RHD (for Power Seat)
      Tester Connection Condition Specified Condition
      I50-17 (SHD+) - f9-1 (SWR) Always Below 1 Ω
      I50-17 (SHD+) or f9-1 (SWR) - Body ground Always 10 kΩ or higher
      I54-4 (TSL) - f9-5 (THR) Always Below 1 Ω
      I54-4 (TSL) or f9-5 (THR) - Body ground Always 10 kΩ or higher
      I54-8 (SG-6) - f9-2 (PR) Always Below 1 Ω
      I54-8 (SG-6) or f9-2 (PR) - Body ground Always 10 kΩ or higher
      for RHD (for Manual Seat)
      Tester Connection Condition Specified Condition
      I50-17 (SHD+) - P43-1 (SWR) Always Below 1 Ω
      I50-17 (SHD+) or P43-1 (SWR) - Body ground Always 10 kΩ or higher
      I54-4 (TSL) - P43-5 (THR) Always Below 1 Ω
      I54-4 (TSL) or P43-5 (THR) - Body ground Always 10 kΩ or higher
      I54-8 (SG-6) - P43-2 (PR) Always Below 1 Ω
      I54-8 (SG-6) or P43-2 (PR) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  8. CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


    1. Temporarily replace the air conditioning amplifier assembly with a new or known good one.

      Click here

    2. Check that the seat heater system is operated normally.

      OK
      The seat heater system is operated normally.
      Result
      Proceed to
      OK
      NG

    OK

    END (AIR CONDITIONING AMPLIFIER ASSEMBLY WAS DEFECTIVE)

    NG

    REPLACE AIR CONDITIONING CONTROL ASSEMBLY Click here

  9. CHECK HARNESS AND CONNECTOR (FRONT SEAT CUSHION PAD WITH COVER RH - BATTERY AND BODY GROUND)


    1. B0059D1C24
      *a

      Front view of wire harness connector

      (to Front Seat Cushion Pad with Cover RH)

      Disconnect the front seat cushion pad with cover RH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      f19-6 (E) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      f19-4 (B1) - Body ground Engine switch on (IG) 11 to 14 V
      f19-4 (B1) - Body ground Engine switch off Below 1 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  10. INSPECT FRONT SEAT CUSHION PAD WITH COVER RH


    1. Remove the front seat cushion pad with cover RH.

      Click here

    2. Inspect the front seat cushion pad with cover RH.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT SEAT CUSHION PAD WITH COVER RH Click here

    OK

  11. INSPECT FRONT SEATBACK PAD WITH COVER RH


    1. Remove the front seatback pad with cover RH.

      Click here

    2. Inspect the front seatback pad with cover RH.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT SEATBACK PAD WITH COVER RH Click here

    OK

  12. CHECK SEAT HEATER CONTROL SUB-ASSEMBLY RH


    1. Temporarily replace the seat heater control sub-assembly RH with a new or known good one.

      Click here

    2. Check that the seat heater system is operated normally.

      OK
      The seat heater system is operated normally.
      Result
      Proceed to
      OK
      NG

    OK

    END (SEAT HEATER CONTROL SUB-ASSEMBLY RH WAS DEFECTIVE)

    NG

  13. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - FRONT SEAT CUSHION PAD WITH COVER RH)


    1. Disconnect the I50 and I54 air conditioning amplifier assembly connectors.

    2. Disconnect the f19 front seat cushion pad with cover RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      I50-16 (SHP+) - f19-1 (SW) Always Below 1 Ω
      I50-16 (SHP+) or f19-1 (SW) - Body ground Always 10 kΩ or higher
      I54-3 (TSR) - f19-5 (TH) Always Below 1 Ω
      I54-3 (TSR) or f19-5 (TH) - Body ground Always 10 kΩ or higher
      I54-7 (SG-3) - f19-2 (P) Always Below 1 Ω
      I54-7 (SG-3) or f19-2 (P) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      I50-17 (SHD+) - f19-1 (SW) Always Below 1 Ω
      I50-17 (SHD+) or f19-1 (SW) - Body ground Always 10 kΩ or higher
      I54-4 (TSL) - f19-5 (TH) Always Below 1 Ω
      I54-4 (TSL) or f19-5 (TH) - Body ground Always 10 kΩ or higher
      I54-8 (SG-6) - f19-2 (P) Always Below 1 Ω
      I54-8 (SG-6) or f19-2 (P) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    GO TO STEP 8 Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR