THEFT DETERRENT SYSTEM SYSTEM DESCRIPTION


  1. OUTLINE OF THEFT DETERRENT SYSTEM


    • The theft deterrent system can be set by locking the doors using any of the following operations:


      • Entry lock operation

      • Wireless lock operation

      • Key linked lock operation

      • By opening and closing the doors

        Tech Tips

        Vehicles not Displaying the Item "Security control with mechanism key" on the GTS Vehicles Displaying the Item "Security control with mechanism key" on the GTS Vehicles Displaying the Item "Security control with mechanism key" on the GTS and not Equipped with Door Ajar Warning Buzzer Function
        Entry lock operation ○ ○* ○
        Wireless lock operation ○ ○ ○
        Key linked lock operation ○ - -
        By opening and closing the doors ○ - -

        *: w/ Entry Function


        • ○: Available

        • -: Not Available

    • In the armed state, the alarm function will be activated if one of the following conditions is met:


      • Any of the doors are unlocked.

      • Any of the doors, the engine hood or the back door is opened.

      • The theft warning ultrasonic sensor (intrusion sensor) detects movement inside the cabin.*1

      • The theft warning ultrasonic sensor (tilt sensor) detects that the vehicle is tilted.*2


      • *1: w/ Intrusion Sensor Cancel Switch

      • *2: w/ Tilt Sensor

    • In the alarm sounding state, the system blinks the turn signal lights. At the same time, the system sounds the vehicle horns and security horn assembly*1 or theft warning siren assembly*2 to deter break-in and theft as well as to warn people around the vehicle.


      • *1: w/ Security Horn Assembly

      • *2: w/o Security Horn Assembly

    • The theft deterrent system can be canceled by unlocking the doors using the following operation:


      • Entry lock operation

      • Wireless lock operation

      • Key linked lock operation

        Tech Tips

        Vehicles not Displaying the Item "Security control with mechanism key" on the GTS Vehicles Displaying the Item "Security control with mechanism key" on the GTS Vehicles Displaying the Item "Security control with mechanism key" on the GTS and not Equipped with Door Ajar Warning Buzzer Function
        Entry lock operation ○ ○*1 ○
        Wireless lock operation ○ ○ ○
        Key linked lock operation ○

        -

        (○)*2

        -

        (○)*2

        *1: w/ Entry Function

        *2: This function is set through the customize function.

        Click here


        • ○: Available

        • -: Not Available

    • The theft deterrent system has an active arming mode. There are 4 states in this mode: a disarmed state, an arming preparation state, an armed state and an alarm sounding state.


    1. Disarmed state:


      • The alarm function is not operating.

      • The theft deterrent system is not operating.

    2. Arming preparation state:


      • The time until the system goes into the armed state.

      • The theft deterrent system is not operating.

    3. Armed state:


      • The theft deterrent system is operating.

    4. Alarm sounding state:


      • The alarm function is operating.

      Alarm Methods and Time
      Alarm Method Turn Signal Lights Blinking
      Vehicle Horns

      Sounding

      (approximately 0.4-second cycles)
      Security Horn Assembly*1

      Sounding

      (approximately 0.4-second cycles)
      Theft Warning Siren Assembly*2 Sounding
      Alarm Time Approximately 27.5 seconds

  • FUNCTION OF MAIN COMPONENTS

    Component Function
    Security indicator light Informs driver of theft deterrent system status.

    • Security horn assembly*1

    • Theft warning siren assembly*2

    		 Sounds when attempted break-in or theft is detected.
    Turn signal lights Blink when attempted break-in or theft is detected.
    Vehicle horns Sound when attempted break-in or theft is detected.

    • Front door courtesy light switch assembly (for LH/RH)

    • Rear door courtesy light switch assembly (for LH/RH)

    		 Detects door status (open or closed).
    Door unlock detection switch Detects door status (locked or unlocked).
    Engine hood courtesy switch (hood lock assembly) Detects engine hood status (open or closed).
    Back door courtesy light switch (back door lock assembly) Detects back door status (open or closed).
    Intrusion sensor cancel switch*3

    • Sends a signal to the main body ECU (multiplex network body ECU) to cancel the theft warning ultrasonic sensor (intrusion sensor).*3

    • Sends a signal to the main body ECU (multiplex network body ECU) to cancel the theft warning ultrasonic sensor (tilt sensor).*4
    Certification ECU (smart key ECU assembly)

    • Receives wireless door lock/unlock signal.

    • Receives entry door lock/unlock signal.*5
    Theft warning ultrasonic sensor (intrusion sensor)*3 Sends a signal to the main body ECU (multiplex network body ECU) to sound the alarm when detecting an intrusion.
    Theft warning ultrasonic sensor (tilt sensor)*4 Sends a signal to the main body ECU (multiplex network body ECU) to sound the alarm when detecting a change in the pitch angle of the vehicle inclination.

  • ACTIVE ARMING MODE


    1. Active arming mode:

      This system operates as described in the diagram below when one of the items for each condition is met.

      Tech Tips

      The term "all doors" used in this section refers to the driver door, front passenger door, rear door LH and rear door RH and back door.

      B0058M5E13
      Vehicles not displaying the item "Security control with mechanism key" on the GTS
      Condition Item
      Condition [1]

      In disarmed state 1, when the engine switch is off, the system state is switched if the following condition is met:


      • With all doors and the engine hood closed, all doors are locked by wireless operation, the entry and start system or key linked power door lock operation.

      In disarmed state 1, when the engine switch is off, the engine hood is closed and all doors are locked, the system state is switched if the following condition is met:


      • The state changes from any of the doors being opened to all doors being closed.
      Condition [2]

      • Allow approximately 30 seconds to elapse.
      Condition [3]

      One of the following conditions is met:


      • All doors are unlocked by wireless operation, the entry and start system or key linked power door lock operation.

      • Any door is unlocked.

      • Any door is opened.

      • The engine switch is pushed.

      • The engine switch is turned on (ACC) or on (IG).

      • The battery is reconnected.
      Condition [4]

      One of the following conditions is met:


      • The engine hood is opened when the engine hood is closed.

      • The theft warning ultrasonic sensor (intrusion sensor) detects movement within the vehicle.*1

      • The theft warning ultrasonic sensor (tilt sensor) detects a change in the pitch angle of the vehicle inclination.*2

      • The glass breakage sensor detects that glass is broken.*2

      • Any door is opened when all doors are closed.

      • Any door is unlocked when all doors are locked.

      • When 5 seconds or more have elapsed after the engine switch is pressed, the power source mode is changed from off to on (IG) without pressing the engine switch.

      Note

      Ultrasonic waves are used to detect intrusion. Ultrasonic waves do not penetrate steel or glass. When any of the door windows is left open, ultrasonic waves may escape. This may result in the detection of people in the surroundings, leaves or insects entering the vehicle, strong wind or other ultrasonic wave sources in the environment when the vehicle is parked with the door windows open. When parking the vehicle with the door windows open for ventilation, turn off the theft warning ultrasonic sensor (intrusion sensor) using the intrusion sensor cancel switch.*1
      Condition [5]

      One of the following conditions is met:


      • The engine switch is turned on (IG) and the engine is running at 550 rpm for 2 seconds or more.

      • All doors are unlocked by wireless operation, the entry and start system or key linked power door lock operation.

      • The engine switch is turned on (ACC) or on (IG) within 5 seconds after the engine switch is pushed.

      • The power back door is opened with the wireless one motion function.*3
      Condition [6]

      • After approximately 27.5 seconds, the alarm stops and the system returns to the armed state.
      Condition [7]

      One of the following conditions is met:


      • The open engine hood is closed with all the doors closed.

      • The power back door reservation lock is operated with the engine hood and a door other than the back door closed.*3
      Condition [8]

      One of the following conditions is met:


      • Any door is unlocked when all doors are locked.

      • Any door is opened.

      • The engine switch is pushed.

      • The engine switch is turned on (ACC) or on (IG).

      • The battery is reconnected.

      • All doors are unlocked by wireless operation, the entry and start system or key linked power door lock operation.

      • The power back door is opened with the wireless one motion function.*3

      • During a close operation, the power back door reverses operation, stops partway or another door opens.*3
      Condition [9]

      In disarmed state 1, when the engine switch is off, the system state is switched if the following condition is met:


      • With all doors closed and the engine hood open, all doors are locked by wireless operation, the entry and start system or key linked power door lock operation.

      In disarmed state 1, when the engine switch is off, the engine hood and back door are open and all doors are locked, the system state is switched if the following condition is met:


      • The state changes from any of the doors being opened to all doors being closed.

      In disarmed state 1, when the engine switch is off, the system state is switched if the following condition is met:


      • During a power back door close operation with all other doors closed, the doors are locked (power back door reservation lock) by wireless operation.*3
      Condition [10]

      • The engine hood is opened.

      • *1: w/ Intrusion Sensor Cancel Switch

      • *2: w/ Tilt Sensor

      • *3: w/ Power Back Door System

      Vehicles displaying the item "Security control with mechanism key" on the GTS
      Condition Item
      Condition [1]

      In disarmed state 1, when the engine switch is off, the system state is switched if the following condition is met:


      • With all doors and the engine hood closed, all doors are locked by wireless operation or the entry and start system.*1

      • With all doors and the engine hood closed, all doors are locked by wireless operation.*2
      Condition [2]

      • Allow approximately 30 seconds to elapse.*3

      • Allow approximately 9 seconds to elapse.*4
      Condition [3]

      One of the following conditions is met:


      • All doors are unlocked by wireless operation or the entry and start system.*1

      • All doors are unlocked by wireless operation.*2

      • Any door is unlocked.

      • Any door is opened.

      • The engine switch is pushed.

      • The engine switch is turned on (ACC) or on (IG).

      • The battery is reconnected.
      Condition [4]

      One of the following conditions is met:


      • The engine hood is opened when the engine hood is closed.

      • The back door is opened when the back door is closed.

      • The theft warning ultrasonic sensor (intrusion sensor) detects movement within the vehicle.*5

      • The theft warning ultrasonic sensor (tilt sensor) detects a change in the pitch angle of the vehicle inclination.*6

      • The glass breakage sensor detects that glass is broken.*6

      • Any door is opened when all doors are closed.

      • Any door is unlocked when all doors are locked.

      • When 5 seconds or more have elapsed after the engine switch is pressed, the power source mode is changed from off to on (IG) without pressing the engine switch.

      • The engine hood is open.

      • Any door is opened.

      • The power source mode is on (IG).

      Note

      Ultrasonic waves are used to detect intrusion. Ultrasonic waves do not penetrate steel or glass. When any of the door windows is left open, ultrasonic waves may escape. This may result in the detection of people in the surroundings, leaves or insects entering the vehicle, strong wind or other ultrasonic wave sources in the environment when the vehicle is parked with the door windows open. When parking the vehicle with the door windows open for ventilation, turn off the theft warning ultrasonic sensor (intrusion sensor) using the intrusion sensor cancel switch.*5
      Condition [5]

      One of the following conditions is met:


      • The engine switch is turned on (IG) and the engine is running at 550 rpm for 2 seconds or more.

      • All doors are unlocked by wireless operation or the entry and start system.*1

      • All doors are unlocked by wireless operation.*2

      • The power back door is opened with the wireless one motion function.*7
      Condition [6]

      • After approximately 27.5 seconds, the alarm stops and 5 seconds later the system returns to the armed state.
      Condition [7]

      One of the following conditions is met:


      • The open engine hood is closed with all the doors closed.

      • The power back door reservation lock is operated with the engine hood and a door other than the back door closed.*7
      Condition [8]

      One of the following conditions is met:


      • Any door is unlocked when all doors are locked.

      • Any door is opened.

      • The engine switch is pushed.

      • The engine switch is turned on (ACC) or on (IG).

      • The battery is reconnected.

      • All doors are unlocked by wireless operation, the entry and start system.*1

      • All doors are unlocked by wireless operation.*2

      • The power back door is opened with the wireless one motion function.*7

      • During a close operation, the power back door reverses operation, stops partway or another door opens.*7
      Condition [9]

      In disarmed state 1, when the engine switch is off, the system state is switched if the following condition is met:


      • With all doors closed and the engine hood and back door open, all doors are locked by wireless operation or the entry and start system.*1

      • With all doors closed and the engine hood and back door open, all doors are locked by wireless operation.*2

      In disarmed state 1, when the engine switch is off, the system state is switched if the following condition is met:


      • During a power back door close operation with all other doors closed, the doors are locked (power back door reservation lock) by wireless operation.*7
      Condition [10]

      • The engine hood is opened.

      • *1: w/ Entry Function

      • *2: w/o Entry Function

      • *3: w/ Door Ajar Warning Buzzer Function

      • *4: w/o Door Ajar Warning Buzzer Function

      • *5: w/ Intrusion Sensor Cancel Switch

      • *6: w/ Tilt Sensor

      • *7: w/ Power Back Door System

  • FORCED DOOR LOCK CONTROL


    1. The forced door lock control prevents the vehicle from being tampered with. Immediately after a door is unlocked (armed state), all doors are forced to lock by a forced door lock signal.


      1. If the following conditions are met, the forced door lock control is operated.


        • The theft deterrent system is in the armed state.

        • Any door is unlocked.

  • PANIC ALARM CONTROL (w/ Panic Switch)


    1. Panic alarm control makes it possible to voluntarily set off the panic alarm by pressing the panic switch on the electrical key transmitter sub-assembly.


      1. Conditions that cause panic alarm control to set off the panic alarm:

        The panic switch on the electrical key transmitter sub-assembly is pressed under the following conditions:


        • The engine switch is off.

        • The theft deterrent system is not in the alarm sounding state.

      2. Conditions that cause the panic alarm control to shut off the alarm:

        Any of the following conditions is met during panic alarm control operation:


        • The engine switch is turned on (IG).

        • The panic switch is pressed again.

        • Any of the switches on the electrical key transmitter sub-assembly (lock/unlock/back door open) is pressed.

        • The panic alarm ends (approximately 27.5 seconds have elapsed).

        • The theft deterrent system switches to the alarm sounding state. Under this condition, the theft deterrent system controls the alarm rather than the panic alarm control. In order to cancel this alarm, refer to the theft deterrent system alarm sounding state cancellation procedure.

  • THEFT WARNING ULTRASONIC SENSOR (INTRUSION SENSOR) (w/ Intrusion Sensor Cancel Switch)

    Note

    Ultrasonic waves are used to detect intrusion. Ultrasonic waves do not penetrate steel or glass. When any of the door windows is left open, ultrasonic waves may escape. This may result in the detection of people in the surroundings, leaves or insects entering the vehicle, strong wind or other ultrasonic wave sources in the environment when the vehicle is parked with the door windows open. When parking the vehicle with the door windows open for ventilation, turn off the theft warning ultrasonic sensor (intrusion sensor) using the intrusion sensor cancel switch.


    1. A theft warning ultrasonic sensor (intrusion sensor) is provided in the map light assembly located in the front of the vehicle interior.

    2. The main body ECU (multiplex network body ECU) activates the theft warning ultrasonic sensor (intrusion sensor) when the system changes from the disarmed state to the armed preparation state. If an intrusion detection signal is input from the theft warning ultrasonic sensor (intrusion sensor) during the armed state, the main body ECU (multiplex network body ECU) changes to the alarm sounding state in order to output an alarm.*1

    3. The main body ECU (multiplex network body ECU) activates the theft warning ultrasonic sensor (intrusion sensor) when the system changes from the disarmed state to the armed preparation state.*2


      • All windows are closed:

        If an intrusion detection signal is input after the glass breakage signal is input from the theft warning ultrasonic sensor (intrusion sensor) during the armed state, the main body ECU (multiplex network body ECU) changes to the alarm state in order to output an alarm.

      • Any window is opened:

        If an intrusion detection signal is input from the theft warning ultrasonic sensor (intrusion sensor) during the armed state, the main body ECU (multiplex network body ECU) changes to the alarm state in order to output an alarm.


      • *1: w/ Door Ajar Warning Buzzer Function

      • *2: w/o Door Ajar Warning Buzzer Function

    4. When the system is in the disarmed state, the function of the theft warning ultrasonic sensor (intrusion sensor) can be disabled by pressing the intrusion sensor cancel switch.

    5. The theft warning ultrasonic sensor (intrusion sensor) may erroneously detect intrusion in the following states:


      • Persons or pets are in the vehicle.

      • The vehicle is parked in a place where extreme vibrations or noises occur, such as in a parking garage.

      • Ice or snow is removed from the vehicle, causing the vehicle to receive repeated impacts or vibrations.

      • The wind or something similar causes an externally mounted reflectively coated windshield cover to move.

      • The theft warning ultrasonic sensor (intrusion sensor) may react to a hanger or other objects hanging in the cabin when they drop or swing.

      • The system changes to the armed state even when any of the windows is open. The theft warning ultrasonic sensor (intrusion sensor) may react to objects moving outside the vehicle when any of the windows is open.

      • The vehicle is inside an automatic or high-pressure car wash.

      • The vehicle experiences impacts, such as hail, lightning strikes and other kinds of repeated impacts or vibrations.

  • THEFT WARNING ULTRASONIC SENSOR (TILT SENSOR) (w/ Tilt Sensor)


    1. The theft warning ultrasonic sensor (tilt sensor) detects the pitch angle of vehicle inclination using 2 deceleration sensors. When the theft warning ultrasonic sensor (tilt sensor) detects a change in the pitch angle of vehicle inclination, such as a thief attempting to tow the vehicle, it transmits the warning signal to the main body ECU (multiplex network body ECU).

    2. The main body ECU (multiplex network body ECU) activates the theft warning ultrasonic sensor (tilt sensor) when the system changes from the armed preparation state to the armed state. If a warning signal is received from the theft warning ultrasonic sensor (tilt sensor) when in the armed state, the main body ECU (multiplex network body ECU) changes to the alarm sounding state in order to sound the alarm.

    3. When the system is in the disarmed state, pressing the intrusion sensor cancel switch disables the function of the theft warning ultrasonic sensor (tilt sensor). If the system changes to the armed state, the theft warning ultrasonic sensor (tilt sensor) will not activate. This function is canceled each time all doors are unlocked by the wireless operation, entry and start system or key linked power door lock operation, and is reinstated when the theft warning ultrasonic sensor (tilt sensor) is on.

    4. Under the following conditions, if the vehicle tilts or acceleration in the vertical or horizontal direction is detected by the theft warning ultrasonic sensor (tilt sensor), the alarm may activate accidentally. To avoid accidental alarm activation, turn the theft warning ultrasonic sensor (tilt sensor) off using the intrusion sensor cancel switch.


      • The vehicle is transported by a ferry, trailer or train.

      • The vehicle is parked in a multi-story parking facility.

      • The vehicle is washed by a conveyor type car washing machine.

      • A tire blows out.

      • The vehicle is jacked up for a tire or wheel change.

      • An earthquake occurs or the road subsides.

      • Goods such as skis or snowboards are loaded or unloaded.

  • THEFT WARNING SIREN ASSEMBLY (w/o Security Horn Assembly)


    1. The theft warning siren assembly has an internal battery. If power to the theft warning siren assembly is interrupted or the communication line is open, the theft warning siren assembly detects it and sounds the alarm using the internal battery.

    2. The theft warning siren assembly has the following alarm controls: normal alarm control and open circuit alarm control. Under normal alarm control, the alarm sounds based on instructions from the main body ECU (multiplex network body ECU) whereas under open circuit alarm control, the theft warning siren assembly judges current security conditions and sounds the alarm by itself.


      1. Normal alarm control

        The theft warning siren assembly sounds when the theft deterrent system is in the alarm sounding state and does not sound when the system is not in the alarm sounding state.

        Tech Tips

        If communication interruption between the theft warning siren assembly and main body ECU (multiplex network body ECU) continues for 70 seconds or more while the theft deterrent system is in the alarm sounding state, the theft warning siren assembly stops sounding.

      2. B005875E02

        Open circuit alarm control

        The theft warning siren assembly changes between the disarmed state and armed state in accordance with the theft deterrent system changes between the disarmed state and armed state. If the power source, ground or communication line is open while the theft warning siren assembly is in the armed state, the theft warning siren assembly sounds.

        During the open circuit alarm sounding state, the theft warning siren assembly sounds intermittently for 27.5 seconds and then stops for 5 seconds. This pattern repeats a maximum of 9 times.

        The intermittent sounding will stop when either condition is met:

        1. The theft warning siren assembly changes to the disarmed state.

        2. The open circuit is returned to normal.

        B0059WPE03

  • SECURITY INDICATOR LIGHT OUTPUT


    1. According to the state of the theft deterrent system, the main body ECU (multiplex network body ECU) outputs a signal to turn the security indicator light on. However, some of the actual lighting conditions of the security indicator light are different from the output signals of the main body ECU (multiplex network body ECU).

      Output
      State of Theft Deterrent System Security Indicator Light
      Output Signal from Main Body ECU (Multiplex Network Body ECU) Actual Lighting Condition
      Disarmed state (1), (2) Off

      • Off (Immobiliser system unset)

      • Blinking (Immobiliser system set)
      Arming preparation state On On
      Armed state Off Blinking
      Alarm sounding state On On
      Blinking Cycle
      Time Security Indicator Light
      0.125 seconds On
      1.875 seconds Off

      Tech Tips

      When the immobiliser system is set, the security indicator light blinks during both the disarmed state and the armed state due to output signals from the immobiliser system.

  • CHECK THEFT WARNING ULTRASONIC SENSOR (INTRUSION SENSOR) (w/ Intrusion Sensor Cancel Switch) (w/o Door Ajar Warning Buzzer Function)

    Note

    Perform the theft warning ultrasonic sensor (intrusion sensor) operation inspection with the GTS disconnected.


    1. Check that the engine hood is closed.

    2. Check the theft warning ultrasonic sensor (intrusion sensor) operation (customize setting "Intrusion Sensor Sound Detection Function" is "ON").


      1. Turn the engine switch off.

      2. Lock all the doors using the wireless door lock or entry door lock function and check that the security indicator light illuminates (armed preparation state) (all windows need to be closed).

      3. Wait 30 seconds after locking all the doors using the wireless door lock or entry door lock function and check that the security indicator light blinks (armed state). Then, make a loud sound by hitting metal objects together (jangle a bunch of keys, etc.) near the theft warning ultrasonic sensor (intrusion sensor) in the vehicle and check that the theft deterrent system alarm operates due to movement inside the vehicle.

        Tech Tips

        If the electrical key transmitter is within the entry exterior area at this time, the alarm does not operate due to the theft warning ultrasonic sensor (intrusion sensor).

      4. Perform an unlock operation using the wireless or entry operation to stop the alarm.

    3. Check the theft warning ultrasonic sensor (intrusion sensor) operation (customize setting "Intrusion Sensor Sound Detection Function" is "OFF").


      1. Turn the engine switch off.

      2. Lock all the doors using the wireless door lock or entry door lock function and check that the security indicator light illuminates (armed preparation state) (all windows need to be opened).

      3. Wait 30 seconds after locking all the doors using the wireless door lock or entry door lock function and check that the security indicator light blinks (armed state). Then, check that the theft deterrent system alarm operates due to movement inside the vehicle.

        Tech Tips

        If the electrical key transmitter is within the entry exterior area at this time, the alarm does not operate due to the intrusion sensor.

      4. Perform an unlock operation using the wireless or entry operation to stop the alarm.

  • CHECK THEFT WARNING ULTRASONIC SENSOR (INTRUSION SENSOR) (w/ Intrusion Sensor Cancel Switch) (w/ Door Ajar Warning Buzzer Function)


    1. Check that the engine hood is closed.

    2. Check the theft warning ultrasonic sensor (intrusion sensor) operation.


      1. Turn the engine switch off.

      2. Lock all the doors using the wireless door lock or entry door lock function and check that the security indicator light illuminates (armed preparation state) (all windows need to be opened).

      3. Wait 30 seconds after locking all the doors using the wireless door lock or entry door lock function and check that the security indicator light blinks (armed state). Then, check that the theft deterrent system alarm operates due to movement inside the vehicle.

        Tech Tips

        If the electrical key transmitter is within the entry exterior area at this time, the alarm does not operate due to the intrusion sensor.

      4. Perform an unlock operation using the wireless or entry operation to stop the alarm.

  • CHECK INTRUSION SENSOR CANCEL SWITCH (w/ Intrusion Sensor Cancel Switch) (w/o Door Ajar Warning Buzzer Function)

    Note

    Perform the theft warning ultrasonic sensor (intrusion sensor) operation inspection with the GTS disconnected.


    1. Check that the engine hood is closed.

    2. Check the intrusion sensor cancel switch operation (customize setting "Intrusion Sensor Sound Detection Function" is "ON").


      1. Turn the engine switch off.

      2. Press the intrusion sensor cancel switch and check that "Theft sensor OFF" is displayed on the combination meter.

      3. Lock all the doors using the wireless door lock or entry door lock function and check that the security indicator light illuminates (armed preparation state).

      4. Approximately 30 seconds after locking all the doors via wireless operation or smart operation, check that the security indicator light changes to blinking (armed state). Also, after making a metal-on-metal striking sound (such as by shaking keys) near the sensor, check that the auto alarm warning does not operate according to movement in the cabin. At this time, do not bring the electrical key transmitter sub-assembly close to the smart exterior area.

        Tech Tips

        Even if the theft warning ultrasonic sensor (intrusion sensor) is off, the theft deterrent system is in the armed state. Therefore, if any of the doors is manually unlocked, the alarm operates.

    3. Check the intrusion sensor cancel switch operation (customize setting "Intrusion Sensor Sound Detection Function" is "OFF").


      1. Turn the engine switch off.

      2. Press the intrusion sensor cancel switch and check that "Theft sensor OFF" is displayed on the combination meter.

      3. Lock all the doors using the wireless door lock or entry door lock function and check that the security indicator light illuminates (armed preparation state).

      4. Approximately 30 seconds after locking all the doors via wireless operation or smart operation, check that the security indicator light changes to blinking (armed state) and the auto alarm does not operate according to movement in the cabin. At this time, do not bring the electrical key transmitter sub-assembly close to the smart exterior area.

        Tech Tips

        Even if the theft warning ultrasonic sensor (intrusion sensor) is off, the theft deterrent system is in the armed state. Therefore, if any of the doors is manually unlocked, the alarm operates.

  • CHECK INTRUSION SENSOR CANCEL SWITCH (w/ Intrusion Sensor Cancel Switch) (w/ Door Ajar Warning Buzzer Function)


    1. Check that the engine hood is closed.

    2. Check the intrusion sensor cancel switch operation.


      1. Turn the engine switch off.

      2. Press the intrusion sensor cancel switch and check that "Theft sensor OFF" is displayed on the combination meter.

      3. Lock all the doors using the wireless door lock or entry door lock function and check that the security indicator light illuminates (armed preparation state).

      4. Approximately 30 seconds after locking all the doors via wireless operation or smart operation, check that the security indicator light changes to blinking (armed state) and the auto alarm does not operate according to movement in the cabin. At this time, do not bring the electrical key transmitter sub-assembly close to the smart exterior area.

        Tech Tips

        Even if the theft warning ultrasonic sensor (intrusion sensor) is off, the theft deterrent system is in the armed state. Therefore, if any of the doors is manually unlocked, the alarm operates.