LIN COMMUNICATION SYSTEM TERMINALS OF ECU


  1. CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


    1. Remove the main body ECU (multiplex network body ECU).


      B005AH5C16
      *1 Main Body ECU (Multiplex Network Body ECU) - -

    2. Connect the instrument panel junction block assembly connectors.

    3. Measure the voltage and resistance according to the value(s) in the table below.

      Tech Tips

      Measure the values on the wire harness side with the connectors disconnected.

      Tester Connection Wiring Color Terminal Description Condition Specified Condition
      A-11 (GND1) - Body ground - Ground Always Below 1 Ω
      A-31 (BECU) - Body ground - Battery power supply Always 11 to 14 V
      A-30 (ACC) - Body ground - ACC power supply Engine switch on (ACC) 11 to 14 V
      A-30 (ACC) - Body ground - ACC power supply Engine switch off Below 1 V
      A-32 (IG) - Body ground - IG power supply Engine switch on (IG) 11 to 14 V
      A-32 (IG) - Body ground - IG power supply Engine switch off Below 1 V

    4. Measure the pulse according to the value(s) in the table below.

      Tester Connection Wiring Color Terminal Description Condition Specified Condition
      A-16 (LIN2) - Body ground - LIN communication line Engine switch on (IG) Pulse generation

  2. CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

    B005AOHC01
    *A for LHD
    *B for RHD

    1. Disconnect the M10*1 or L3*2 multiplex network master switch assembly connector.

      *1: for LHD

      *2: for RHD

    2. Measure the resistance and voltage according to the value(s) in the table below.

      for LHD
      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      M10-11 (B) - Body ground SB - Body ground Battery power supply Always 11 to 14 V
      M10-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
      for RHD
      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      L3-11 (B) - Body ground L - Body ground Battery power supply Always 11 to 14 V
      L3-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

    3. Measure the pulse according to the value(s) in the table below.

      for LHD
      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      M10-17 (LIN1) - Body ground R - Body ground LIN communication line Engine switch on (IG) Pulse generation
      for RHD
      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      L3-17 (LIN1) - Body ground G - Body ground LIN communication line Engine switch on (IG) Pulse generation

  3. CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

    B0058UME21

    1. Disconnect the M2 front power window regulator motor assembly LH connector.

    2. Measure the resistance and voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      M2-2 (B) - Body ground

      P - Body ground (for LHD)

      W - Body ground (for RHD)

      		 Battery power supply Always 11 to 14 V
      M2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

    3. Measure the pulse according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      M2-9 (LIN) - Body ground

      W - Body ground (for LHD)

      B - Body ground (for RHD)

      		 LIN communication line Engine switch on (IG) Pulse generation

  4. CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

    B0058UME22

    1. Disconnect the L2 front power window regulator motor assembly RH connector.

    2. Measure the resistance and voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      L2-2 (B) - Body ground G - Body ground Battery power supply Always 11 to 14 V
      L2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

    3. Measure the pulse according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      L2-9 (LIN) - Body ground

      SB - Body ground (for LHD)

      W - Body ground (for RHD)

      		 LIN communication line Engine switch on (IG) Pulse generation

  5. CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

    B0058UME23

    1. Disconnect the O2 rear power window regulator motor assembly LH connector.

    2. Measure the resistance and voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      O2-2 (B) - Body ground LA-Y - Body ground Battery power supply Always 11 to 14 V
      O2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

    3. Measure the pulse according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      O2-9 (LIN) - Body ground P - Body ground LIN communication line Engine switch on (IG) Pulse generation

  6. CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

    B0058UME24

    1. Disconnect the N2 rear power window regulator motor assembly RH connector.

    2. Measure the resistance and voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      N2-2 (B) - Body ground LA-G - Body ground Battery power supply Always 11 to 14 V
      N2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

    3. Measure the pulse according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      N2-9 (LIN) - Body ground L - Body ground LIN communication line Engine switch on (IG) Pulse generation

  7. CHECK SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (w/ Sliding Roof System or Roof Sunshade System)

    B0059LVE06

    1. Disconnect the T9 sliding roof drive gear sub-assembly connector.

    2. Measure the resistance and voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      T9-8 (B) - Body ground W - Body ground Battery power supply Always 11 to 14 V
      T9-12 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω

    3. Measure the pulse according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      T9-11 (MPX1) - Body ground LG - Body ground LIN communication line Engine switch on (IG) Pulse generation

  8. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    B0058T7E08

    1. Disconnect the I53 certification ECU connector.

    2. Measure the resistance and voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      I53-10 (+B) - Body ground W - Body ground Battery power supply Always 11 to 14 V
      I53-11 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω

    3. Measure the pulse according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      I53-6 (LIN) - Body ground Y - Body ground LIN communication line Engine switch on (IG) Pulse generation

  9. CHECK ID CODE BOX (IMMOBILISER CODE BOX)

    B005A1FE06

    1. Disconnect the I26 ID code box connector.

    2. Measure the resistance and voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      I26-1 (+B) - Body ground B - Body ground Battery power supply Always 11 to 14 V
      I26-5 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

    3. Measure the pulse according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      I26-2 (LIN1) - Body ground V - Body ground LIN communication line Engine switch on (IG) Pulse generation

  10. CHECK STEERING LOCK ACTUATOR ASSEMBLY

    B005AJ2E02

    1. Disconnect the I2 steering lock actuator assembly connector.

    2. Measure the resistance and voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      I2-7 (B) - Body ground L - Body ground Battery power supply Always 11 to 14 V
      I2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

    3. Measure the pulse according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      I2-5 (LIN) - Body ground G - Body ground LIN communication line Engine switch on (IG) Pulse generation

  11. CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

    B0059OME15

    1. Disconnect the I50 air conditioning amplifier assembly connector.

    2. Measure the resistance and voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      I50-1 (IG+) - Body ground SB - Body ground IG power supply Engine switch off Below 1 V
      I50-1 (IG+) - Body ground SB - Body ground IG power supply Engine switch on (IG) 11 to 14 V
      I50-21 (B) - Body ground GR - Body ground Battery power supply Always 11 to 14 V
      I50-14 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

    3. Measure the pulse according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      I50-37 (LIN) - Body ground B - Body ground LIN communication line Engine switch on (IG) Pulse generation

  12. CHECK AIR CONDITIONING CONTROL ASSEMBLY

    B0059R2E03

    1. Disconnect the I13 air conditioning control assembly connector.

    2. Measure the resistance and voltage according to the value(s) in the table below.

      w/o Stop and Start System
      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      I13-8 (IG+) - Body ground LG - Body ground IG power supply Engine switch on (IG) 11 to 14 V
      I13-8 (IG+) - Body ground LG - Body ground IG power supply Engine switch off Below 1 V
      I13-14 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
      w/ Stop and Start System
      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      I13-8 (IG+) - Body ground W - Body ground IG power supply Engine switch on (IG) 10.5 to 16 V
      I13-8 (IG+) - Body ground W - Body ground IG power supply Engine switch off Below 1 V
      I13-14 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

    3. Measure the pulse according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      I13-6 (LIN) - Body ground B - Body ground LIN communication line Engine switch on (IG) Pulse generation

  13. CHECK RAIN SENSOR (w/ Rain Sensor)

    B0058RDE05

    1. Disconnect the T8 rain sensor connector.

    2. Measure the resistance and voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      T8-4 (SIG) - Body ground GR - Body ground IG power supply Engine switch on (IG) 11 to 14 V
      T8-4 (SIG) - Body ground GR - Body ground IG power supply Engine switch off Below 1 V
      T8-2 (ES) - Body ground W - Body ground Ground Always Below 1 Ω

    3. Measure the pulse according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      T8-1 (MPX) - Body ground V - Body ground LIN communication line Engine switch on (IG) Pulse generation

  14. CHECK WINDSHIELD WIPER RELAY ASSEMBLY (w/ Rain Sensor)

    B005AOWE02

    1. Disconnect the I56 windshield wiper relay assembly connector.

    2. Measure the resistance and voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      I56-2 (IG) - Body ground L - Body ground IG power supply Engine switch on (IG) 11 to 14 V
      I56-2 (IG) - Body ground L - Body ground IG power supply Engine switch off Below 1 V
      I56-12 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω
      I56-16 (WIG) - Body ground L - Body ground Battery power supply Engine switch on (IG) 11 to 14 V
      Engine switch off Below 1 V

    3. Measure the pulse according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      I56-14 (MPX1) - Body ground V - Body ground LIN communication line Engine switch on (IG) Pulse generation

  15. CHECK DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY (w/Double Locking System)

    B0057QPE02

    1. Disconnect the I129 double lock door control relay assembly connector.

    2. Measure the resistance and voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      I129-7 (CPUB) - Body ground L - Body ground Battery power supply Engine switch off 11 to 14 V
      I129-1 (+B) - Body ground G - Body ground Battery power supply Always 11 to 14 V
      I129-14 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

    3. Measure the pulse according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      I129-9 (MPX1) - Body ground V - Body ground LIN communication line Engine switch on (IG) Pulse generation

  16. CHECK KICK DOOR CONTROL SENSOR (w/ Hands Free Power Back Door)

    B005AQ4E02

    1. Disconnect the W9 kick door control sensor connector.

    2. Measure the resistance and voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      W9-1 (B) - Body ground Y - Body ground Battery power supply Always 11 to 14 V
      W9-4 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

    3. Measure the pulse according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      W9-2 (LIN) - Body ground P - Body ground LIN communication line Engine switch on (IG) Pulse generation