PARKING ASSIST MONITOR SYSTEM Image from Camera for Parking Assist Monitor is Abnormal

DESCRIPTION

The video signal from the rear television camera assembly is transmitted to the radio receiver assembly.

WIRING DIAGRAM

B0057AUE02

CAUTION / NOTICE / HINT

Note


  • When "System initializing" is displayed on the radio receiver assembly after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point.

    Click here

  • Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

    Click here

Tech Tips


    Images may be unclear even in normal conditions if:

  • Electrical devices are used in the cabin (noise may occur in the image).

  • Accessories that generate radio waves have been installed (noise may occur in the image).

  • The outer mirror switch assembly is operated (noise may occur in the image).

  • The camera lens is frosted over (the image immediately after turning the engine switch on (IG) may be blurred or darker than normal).

  • The camera lens is dirty with snow, mud, etc.

  • A strong beam of light, such as a sunbeam or headlight, hits the camera.

  • It is too dark around the camera (at night, etc.).

  • The ambient temperature around the camera is either too high or too low.

  • The vehicle is tilted at a steep angle.

  • The rear television camera assembly lens is scratched.

  • The rear television camera assembly lens has drops of water on it or the humidity is high.

  • When the camera is used under fluorescent lights, sodium lights, mercury lights, etc., the lights and the illuminated area may appear to flicker.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)


    1. Disconnect the I38 radio receiver assembly connector.

    2. Disconnect the Y6 rear television camera assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I38-39 (CA+) - Y6-6 (CB+) Always Below 1 Ω
      I38-18 (V+) - Y6-3 (CV+) Always Below 1 Ω
      I38-19 (V-) - Y6-2 (CV-) Always Below 1 Ω
      I38-40 (CGND) - Y6-5 (CGND) Always Below 1 Ω
      I38-39 (CA+) or Y6-6 (CB+) - Body ground Always 10 kΩ or higher
      I38-18 (V+) or Y6-3 (CV+) - Body ground Always 10 kΩ or higher
      I38-19 (V-) or Y6-2 (CV-) - Body ground Always 10 kΩ or higher
      I38-40 (CGND) or Y6-5 (CGND) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. CHECK RADIO RECEIVER ASSEMBLY (CGND, CA+)


    1. B00587DC31
      *a

      Component with harness connected

      (Radio Receiver Assembly)

      Remove the radio receiver assembly with the connector still connected.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I38-40 (CGND) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      I38-39 (CA+) - I38-40 (CGND) Engine switch on (ACC) 5.5 to 7.05 V
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE RADIO RECEIVER ASSEMBLY Click here

    OK

  3. CHECK REAR TELEVISION CAMERA ASSEMBLY


    1. Remove the radio receiver assembly with the connector still connected.

      B0057JKC10
      *a

      Component with harness connected

      (Radio Receiver Assembly)

      		 *b Waveform 1
      *c Waveform 2 *d Synchronization Signal
      *e Video Waveform - -

    2. Check the waveform of the rear television camera assembly using an oscilloscope.

      Tech Tips

      A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio receiver assembly with the connector connected.

      Item Content
      Terminal No. (Symbol) I38-18 (V+) - I38-40 (CGND)
      Tool Setting 200 mV/DIV., 50 μsec./DIV.
      Condition

      Waveform 1: Engine switch on (IG), shift lever in R, camera lens is not covered, displaying an image

      Waveform 2: Engine switch on (IG), shift lever in R, camera lens is covered, blacking out the screen

      Tech Tips

      The video waveform changes according to the image sent by the rear television camera assembly.

      Result
      Result Proceed to
      Waveform is as shown in the illustration A
      Waveform is not as shown in the illustration B

    B

    REPLACE REAR TELEVISION CAMERA ASSEMBLY Click here

    A

  4. CHECK HARNESS AND CONNECTOR (GVIF CABLE)


    1. Replace the GVIF cable with a new or normally functioning one.

    2. Check if the same malfunction recurs when the parking assist monitor screen is displayed.

      OK
      Malfunction does not reoccur (returns to normal).
      Result
      Proceed to
      OK
      NG

    OK

    END (GVIF CABLE IS DEFECTIVE)

    NG

  5. CHECK MULTI-DISPLAY ASSEMBLY


    1. Replace the multi-display assembly with a new or normally functioning one.

      Click here

    2. Check if the same malfunction recurs when the parking assist monitor screen is displayed.

      OK
      Malfunction does not reoccur (returns to normal).
      Result
      Proceed to
      OK
      NG

    OK

    END (MULTI-DISPLAY ASSEMBLY IS DEFECTIVE)

    NG

    REPLACE RADIO RECEIVER ASSEMBLY Click here