PARKING ASSIST MONITOR SYSTEM DIAGNOSIS SYSTEM


  1. PARKING ASSIST MONITOR DIAGNOSIS SYSTEM


    1. For parking assist monitor system diagnosis, signals received by the radio receiver assembly can be checked and the parking assist monitor system can be calibrated, adjusted and checked using the radio receiver assembly.

      Note

      Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

      Click here

      Tech Tips

      The displayed items may differ depending on vehicle specifications.

  2. DIAGNOSIS SCREEN TRANSITION (DURING PARKING ASSIST MONITOR SYSTEM INITIALIZATION)

    B00582VE01
    *1 Start diagnostic mode
    B0058S3

  3. DIAGNOSIS SCREEN TRANSITION (AFTER PARKING ASSIST MONITOR SYSTEM INITIALIZATION)

    B0057OTE01
    *1 Start diagnostic mode
    B0059WW

  4. VEHICLE SIGNAL CHECK


    1. Start diagnostic mode.

      w/ Navigation System:

      Click here

      w/ Audio and Visual System (for 8 Inch Display):

      Click here

      w/ Audio and Visual System (for 10.3 Inch Display):

      Click here

    2. B0058Z8

      Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.

    3. B0057Z0

      Select "Vehicle Signal" on the "Function Check/Setting I" screen.

      Note

      If the "Camera Setting" selection screen is not displayed, turn the engine switch off and enter the diagnosis screen after turning the engine switch on (IG) once again.

    4. B005AUS

      Vehicle Signal Check Mode


      1. When the "Vehicle Signal Check Mode" screen is displayed, check the item displayed for "REV".

        Tech Tips


        • Only conditions having inputs are displayed.

        • This screen displays vehicle signals input to the radio receiver assembly.

    5. Finish diagnostic mode.

      w/ Navigation System:

      Click here

      w/ Audio and Visual System (for 8 Inch Display):

      Click here

      w/ Audio and Visual System (for 10.3 Inch Display):

      Click here

  5. CAR SIGNAL CHECK (PARKING ASSIST MONITOR SYSTEM INPUT SIGNALS)


    1. B0058Z8

      Start diagnostic mode.

      w/ Navigation System:

      Click here

      w/ Audio and Visual System (for 8 Inch Display):

      Click here

      w/ Audio and Visual System (for 10.3 Inch Display):

      Click here


      1. Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.

      2. B0057Z0

        Select "Camera Setting" on the "Function Check/Setting I" screen.

        Note

        If the "Camera Setting" selection screen is not displayed, turn the engine switch off and enter the diagnosis screen after turning the engine switch on (IG) once again.

        Tech Tips

        After "Next" is selected, the screen transitions differ depending on whether initialization of the parking assist monitor system was performed after the radio receiver assembly was replaced.

        Parking Assist Monitor System Initialization Screen Transition
        Not performed Car Signal Check screen
        Performed Mode Setting screen
      3. B0056YE

        When the screen changes to the "Mode Setting" screen, select "Back Camera Setting" to display the "Signal Check" screen.

        Tech Tips

        To select a grayed out item, select and hold the item for 2 seconds or more.

    2. B005B99

      Signal Check


      1. On the "Signal Check" screen, it is possible to inspect the state of signals and check the settings.

        Item Inspection Detail Note
        CAN CAN communication signal input When "CHK" (red) is displayed, selecting "Next" will not change to the next screen.

        Tech Tips


        • When "CHK" (red) is displayed, perform inspections based on the result of the following inspections.


        • If performing the adjustment after proceeding to the next screen, confirm that all items display "OK" (blue) before selecting "Next".

    3. CAN inspection

      Tech Tips

      If "CHK" (red) is displayed for "CAN", check for DTCs and perform troubleshooting based on the output DTCs.

      Click here

    4. Finish diagnostic mode.

      w/ Navigation System:

      Click here

      w/ Audio and Visual System (for 8 Inch Display):

      Click here

      w/ Audio and Visual System (for 10.3 Inch Display):

      Click here

  6. CAMERA SYNCHRONOUS ERROR HISTORY

    Tech Tips

    This function is used to check the date and time of occurrence when a camera synchronous error occurs.


    1. Check camera synchronous error history.


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Navigation System / Utility / Camera Synchronous Error History.


        Body Electrical > Navigation System > Utility
        Tester Display
        Camera Synchronous Error History

      5. When an item is stored for Camera Synchronous Error History, record it before repairing the radio receiver assembly and rear television camera assembly.

        Tech Tips

        Camera Synchronous Error History can store up to 5 history data items. If a new camera synchronous error occurs when 5 data items have already been stored, the oldest data is cleared and the new data is stored.

    2. Clear camera synchronous error history.


      1. When DTCs are cleared using any of the following operations, Camera Synchronous Error History will be cleared as well.

        Click here


        • Cleared using the GTS.

        • Cleared using the system check mode screen.

        • Cleared using the unit check mode screen.

  7. VIDEO DEVICE CONNECTION CHECK

    Click here

  8. CALIBRATION WHEN SERVICING VEHICLE

    Note

    Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

    Click here