TELEMATICS SYSTEM(w/ Telematics Transceiver for G-BOOK), Diagnostic DTC:B15DB

DTC Code DTC Name
B15DB Telematics Transceiver Disconnected

DESCRIPTION

If the radio receiver assembly cannot detect the telematics transceiver for a certain period of time (90 seconds) after the engine switch is turned on (ACC) and the radio receiver assembly confirms that the information is missing by checking past telematics transceiver recognition information (registered information), this DTC will be stored.

Tech Tips

The telematics system uses USB communication between devices. If an open, short, short to +B or short to ground occurs in the USB circuit, communication is interrupted and the telematics system will not operate normally.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15DB Telematics Transceiver Disconnected telematics transceiver disconnected

  • Harness or connector

  • Telematics transceiver

  • Radio receiver assembly

  • Navigation ECU

Tech Tips

This DTC may be stored due to environmental reasons such as electrical noise or interference.

WIRING DIAGRAM

B0058DXE04

CAUTION / NOTICE / HINT

Note


  • Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for G-BOOK.

    Click here

  • When replacing the telematics transceiver, make sure to replace it with a new one.

  • When replacing the radio receiver assembly or navigation ECU, always replace it with a new one.

    If a radio receiver assembly or navigation ECU which was installed to another vehicle is used, the following may occur:


    • A communication malfunction DTC may be stored.

    • The radio receiver assembly or navigation ECU may not operate normally.

PROCEDURE


  1. CHECK DTC


    1. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    2. Turn the engine switch off.

    3. Turn the engine switch on (IG) and wait for 90 seconds.

    4. Recheck for DTCs and check that no DTCs are output.

      Click here


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

  2. CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - BATTERY AND BODY GROUND)


    1. B0058EWC03
      *a

      Front view of wire harness connector

      (to Telematics Transceiver)

      Disconnect the telematics transceiver connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I40-4 (E) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      I40-1 (+B) - Body ground Always 10.5 to 16 V
      I40-8 (ACC) - Body ground Engine switch on (ACC) 10.5 to 16 V
      I40-7 (IG2) - Body ground Engine switch on (IG) 10.5 to 16 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - DCM [TELEMATICS TRANSCEIVER])


    1. Disconnect the I154 radio receiver assembly connector.

    2. Disconnect the I100 telematics transceiver connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I154-10 (USBV) - I100-4 (USBV) Always Below 1 Ω
      I154-11 (USBG) - I100-2 (USBG) Always Below 1 Ω
      I154-10 (USBV) - Body ground Always 10 kΩ or higher
      I154-11 (USBG) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK RADIO RECEIVER ASSEMBLY (USBV, USBG)


    1. Disconnect the DCM (telematics transceiver) connector.

    2. B005A3XC05
      *a

      Front view of wire harness connector

      (to Telematics Transceiver)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I100-2 (USBG) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      I100-4 (USBV) - I100-2 (USBG) Engine switch on (ACC) 4.75 to 5.25 V
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE RADIO RECEIVER ASSEMBLY Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - NAVIGATION ECU)


    1. B005BI1C05
      *a

      Front view of wire harness connector

      (to Telematics Transceiver)
      *b

      Front view of wire harness connector

      (to Navigation ECU)

      Disconnect the I100 telematics transceiver connector.

    2. Disconnect the I175 navigation ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I100-1-1 (USB-) - I175-2 (USB-) Always Below 1 Ω
      I100-1-2 (USB+) - I175-1 (USB+) Always Below 1 Ω
      I100-1-3 (USBS) - I175-3 (USBS) Always Below 1 Ω
      I100-1-1 (USB-) - Body ground Always 10 kΩ or higher
      I100-1-2 (USB+) - Body ground Always 10 kΩ or higher
      I100-1-3 (USBS) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK TELEMATICS TRANSCEIVER


    1. Replace the telematics transceiver with a new one.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    3. Turn the engine switch off.

    4. Turn the engine switch on (IG) and wait for 90 seconds.

    5. Recheck for DTCs and check that no DTCs are output.

      Click here


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END (TELEMATICS TRANSCEIVER IS DEFECTIVE)

    NG

  7. CHECK NAVIGATION ECU


    1. Replace the navigation ECU with a new one.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    3. Turn the engine switch off.

    4. Turn the engine switch on (IG) and wait for 90 seconds.

    5. Recheck for DTCs and check that no DTCs are output.

      Click here


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END (NAVIGATION ECU IS DEFECTIVE)

    NG

    REPLACE RADIO RECEIVER ASSEMBLY Click here