NAVIGATION SYSTEM, Diagnostic DTC:B15D6

DTC Code DTC Name
B15D6 Display Disconnected

DESCRIPTION

The multi-display assembly and radio receiver assembly are connected by the AVC-LAN communication line.

This DTC is stored when an AVC-LAN communication error occurs between the multi-display assembly and radio receiver assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15D6 Display Disconnected A device that is listed in the AVC-LAN connected device record of the master unit is missing
  • Multi-display assembly power source circuit

  • AVC-LAN circuit between radio receiver assembly and multi-display assembly

  • Multi-display assembly

  • Radio receiver assembly

  • Harness or connector

Tech Tips

For the AVC-LAN communication line, the radio receiver assembly is the master unit.

WIRING DIAGRAM

B00574GE01

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • When replacing the radio receiver assembly, always replace it with a new one.

    If a radio receiver assembly which was installed to another vehicle is used, the following may occur:


    • A communication malfunction DTC may be stored.

    • The radio receiver assembly may not operate normally.

Tech Tips

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click here

PROCEDURE


  1. CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)


    1. Check for optional components.


      1. Check that optional components (including associated wiring) which generate radio waves are not installed.

        Result
        Result Proceed to
        Optional components (including associated wiring) are installed. A
        Optional components (including associated wiring) are not installed. B

        Tech Tips


        • Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

        • This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.


    B
    A
  2. REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)


    1. Remove optional components (including associated wiring).

      Note

      Do not remove optional components or associated wiring without the permission of the customer.

      Result
      Proceed to
      NEXT

    NEXT
  3. CHECK DTC


    1. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs
    2. Recheck for DTCs and check that no DTCs are output.

      Click here


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK
    NG
  4. CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - BATTERY AND BODY GROUND)


    1. B005B6PC27
      *a

      Front view of wire harness connector

      (to Multi-display Assembly)

      Disconnect the multi-display assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I42-13 (GND1) - Body ground Always Below 1 Ω
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      I42-12 (B) - Body ground Always

      11 to 14 V*1

      10.5 to 16 V*2

      I42-24 (ACC) - Body ground Engine switch on (ACC)

      11 to 14 V*1

      10.5 to 16 V*2

      *1: w/o Stop and Start System
      *2: w/ Stop and Start System
      Result
      Proceed to
      OK
      NG

    NG
    OK
  5. INSPECT RADIO RECEIVER ASSEMBLY (TX1+, TX1-)


    1. B0059QVN01

      Remove the radio receiver assembly.

      Click here

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5 (TX1+) - 6 (TX1-) Always 60 to 80 Ω
      Result
      Proceed to
      OK
      NG

    NG
    OK
  6. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MULTI-DISPLAY ASSEMBLY)


    1. Disconnect the I152 radio receiver assembly connector.

    2. Disconnect the I42 multi-display assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I152-5 (TX1+) - I42-7 (TX+) Always Below 1 Ω
      I152-6 (TX1-) - I42-19 (TX-) Always Below 1 Ω
      I152-5 (TX1+) - Body ground Always 10 kΩ or higher
      I152-6 (TX1-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG
    OK
  7. CHECK MULTI-DISPLAY ASSEMBLY


    1. Replace the multi-display assembly with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs
    3. Recheck for DTCs and check that no DTCs are output.

      Click here


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK
    NG