AUDIO AND VISUAL SYSTEM(for 8 Speakers) Microphone Circuit between Microphone and Radio Receiver

DESCRIPTION



WIRING DIAGRAM

A01XNAME02

CAUTION / NOTICE / HINT

Note

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to precaution for audio and visual system.

Click here

PROCEDURE


  1. CHECK MICROPHONE (OPERATION CHECK)


    1. B005A78

      Enter the "Microphone Check" screen. Refer to Check Mic & Voice Recognition in Operation Check.

      Click here

    2. When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

    3. Push the recording switch and perform voice recording.

      Tech Tips


      • Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.

      • Voice can be recorded for up to 5 seconds.

    4. Check that the recording indicator remains on while recording and that the recorded voice is played normally without noise or distortion.

      OK
      All check results are normal.
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE RADIO RECEIVER ASSEMBLY Click here

    NG

  2. CONFIRM MODEL


    1. Choose the model to be inspected.

      Model
      Model Proceed to
      w/o Telematics Transceiver A
      w/ Telematics Transceiver B

    B

    CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY) Click here

    A

  3. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)


    1. Disconnect the I121 radio receiver assembly connector.

    2. Disconnect the T7 map light assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I121-6 (SNS2) - T7-1 (SNS2) Always Below 1 Ω
      I121-4 (MACC) - T7-4 (MACC) Always Below 1 Ω
      I121-5 (MIN+) - T7-3 (MCO+) Always Below 1 Ω
      I121-19 (MIN-) - T7-2 (MCO-) Always Below 1 Ω
      I121-18 (SGND) - Body ground Always 10 kΩ or higher
      I121-6 (SNS2) or T7-1 (SNS2) - Body ground Always 10 kΩ or higher
      I121-4 (MACC) or T7-4 (MACC) - Body ground Always 10 kΩ or higher
      I121-5 (MIN+) or T7-3 (MCO+) - Body ground Always 10 kΩ or higher
      I121-19 (MIN-) or T7-2 (MCO-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT MAP LIGHT ASSEMBLY


    1. A01XNTHN01

      Remove the map light assembly.

      Click here

    2. Remove the telephone microphone assembly.

      Click here

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A-1 (SNS2) - B-3 (SNS2) Always Below 1 Ω
      A-4 (MACC) - B-6 (MACC) Always Below 1 Ω
      A-3 (MCO+) - B-5 (MIC+) Always Below 1 Ω
      A-2 (MCO-) - B-4 (MIC-) Always Below 1 Ω
      A-1 (SNS2) - A-2 (MCO-) Always 10 kΩ or higher
      A-1 (SNS2) - A-3 (MCO+) Always 10 kΩ or higher
      A-1 (SNS2) - A-4 (MACC) Always 10 kΩ or higher
      A-2 (MCO-) - A-3 (MCO+) Always 10 kΩ or higher
      A-2 (MCO-) - A-4 (MACC) Always 10 kΩ or higher
      A-3 (MCO+) - A-4 (MACC) Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE MAP LIGHT ASSEMBLY Click here

    OK

  5. CHECK TELEPHONE MICROPHONE ASSEMBLY


    1. Replace the telephone microphone assembly with a new or known good one.

      Click here

    2. Check the malfunction disappears.

      OK
      Malfunction disappears.
      Result
      Proceed to
      OK
      NG

    OK

    END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  6. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)


    1. Disconnect the I121 radio receiver assembly connector.

    2. Disconnect the T7 map light assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I121-6 (SNS2) - T7-1 (SNS2) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - DCM [TELEMATICS TRANSCEIVER])


    1. Disconnect the I121 radio receiver assembly connector.

    2. Disconnect the I40 DCM (telematics transceiver) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I121-5 (MIN+) - I40-18 (MCO+) Always Below 1 Ω
      I121-19 (MIN-) - I40-19 (MCO-) Always Below 1 Ω
      I121-5 (MIN+) - Body ground Always 10 kΩ or higher
      I121-19 (MIN-) - Body ground Always 10 kΩ or higher
      I121-18 (SGND) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  8. CHECK HARNESS AND CONNECTOR (DCM [TELEMATICS TRANSCEIVER] - MAP LIGHT ASSEMBLY)


    1. Disconnect the I40 DCM (telematics transceiver) connector.

    2. Disconnect the T7 map light assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I40-33 (MCVD) - T7-4 (MACC) Always Below 1 Ω
      I40-34 (MCI+) - T7-3 (MCO+) Always Below 1 Ω
      I40-35 (MCI-) - T7-2 (MCO-) Always Below 1 Ω
      I40-33 (MCVD) - Body ground Always 10 kΩ or higher
      I40-34 (MCI+) - Body ground Always 10 kΩ or higher
      I40-35 (MCI-) - Body ground Always 10 kΩ or higher
      I40-32 (SGND) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  9. INSPECT MAP LIGHT ASSEMBLY


    1. A01XNTHN01

      Remove the map light assembly.

      Click here

    2. Remove the telephone microphone assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A-1 (SNS2) - B-3 (SNS2) Always Below 1 Ω
      A-4 (MACC) - B-6 (MACC) Always Below 1 Ω
      A-3 (MCO+) - B-5 (MIC+) Always Below 1 Ω
      A-2 (MCO-) - B-4 (MIC-) Always Below 1 Ω
      A-1 (SNS2) - A-2 (MCO-) Always 10 kΩ or higher
      A-1 (SNS2) - A-3 (MCO+) Always 10 kΩ or higher
      A-1 (SNS2) - A-4 (MACC) Always 10 kΩ or higher
      A-2 (MCO-) - A-3 (MCO+) Always 10 kΩ or higher
      A-2 (MCO-) - A-4 (MACC) Always 10 kΩ or higher
      A-3 (MCO+) - A-4 (MACC) Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE MAP LIGHT ASSEMBLY Click here

    OK

  10. CHECK DCM (TELEMATICS TRANSCEIVER)


    1. B0057H2C08
      *a

      Component with harness connected

      (DCM [Telematics Transceiver])

      Disconnect the T7 map light assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I40-32 (SGND) - Body ground Always Below 1 Ω
      I40-35 (MCI-) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      I40-33 (MCVD) - Body ground Engine switch on (ACC) 4 to 6 V
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE DCM (TELEMATICS TRANSCEIVER) Click here

    OK

  11. CHECK TELEPHONE MICROPHONE ASSEMBLY


    1. Replace the telephone microphone assembly with a new or known good one.

      Click here

    2. Check the malfunction disappears.

      OK
      Malfunction disappears.
      Result
      Proceed to
      OK
      NG

    OK

    END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

    NG

    REPLACE RADIO RECEIVER ASSEMBLY Click here