AUDIO AND VISUAL SYSTEM(except 8 Speakers) HOW TO PROCEED WITH TROUBLESHOOTING

DTC Code DTC Name
HOW TO PROCEED WITH TROUBLESHOOTING

CAUTION / NOTICE / HINT

Tech Tips


  • Use the following procedure to troubleshoot the audio and visual system.

  • *: Use the GTS.

PROCEDURE


  1. VEHICLE BROUGHT TO WORKSHOP

    Result
    Proceed to
    NEXT

    NEXT

  2. CUSTOMER PROBLEM ANALYSIS


    • When troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

    • Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

    • The following 5 items are important points for problem analysis:

      What Vehicle model, system name
      When Date, time, occurrence frequency
      Where Road conditions
      Under what conditions? Driving conditions, weather conditions
      How did it happen? Problem symptoms
    Result
    Proceed to
    NEXT

    NEXT

  3. INSPECT BATTERY VOLTAGE


    1. Measure the battery voltage.

      Standard voltage
      11 to 14 V

      Tech Tips

      If the voltage is below 11 V, recharge or replace the battery before proceeding.

      Result
      Proceed to
      NEXT

    NEXT

  4. CHECK CABIN


    1. Check that condensation is not likely to occur in the cabin and that the temperature is not high or extremely low in the cabin.

      OK
      Condensation is not likely being produced and the temperature is not high or extremely low.

      Tech Tips


      • A humid cabin and a rapid change in temperature may lead to condensation. Condensation in the cabin may cause a short circuit.

      • The audio and visual system may not operate normally when the temperature is -20°C (-4°F) or lower, or 65°C (149°F) or higher.

      Result
      Proceed to
      OK
      NG

    NG

    SET CABIN TO APPROPRIATE TEMPERATURE

    OK

  5. CHECK CAN COMMUNICATION SYSTEM*


    1. Check if the CAN communication system is functioning normally.

      for LHD: Click here

      for RHD: Click here

      Result
      Result Proceed to
      CAN communication system is functioning normally A
      CAN communication system is not functioning normally (for LHD) B
      CAN communication system is not functioning normally (for RHD) C

    B

    GO TO CAN COMMUNICATION SYSTEM Click here

    C

    GO TO CAN COMMUNICATION SYSTEM Click here

    A

  6. CHECK FOR DTC*


    1. Check for DTCs and note any codes that are output.

      Click here


      Body Electrical > Navigation System > Trouble Codes

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    3. Recheck for DTCs by simulating the operation indicated by the DTCs.

      Click here


      Body Electrical > Navigation System > Trouble Codes
      Result
      Result Proceed to
      No DTC is output (w/ Sound Library Function) A
      No DTC is output (w/o Sound Library Function) B
      DTCs are output C

    B

    GO TO STEP 8 Click here

    C

    GO TO DIAGNOSTIC TROUBLE CODE CHART Click here

    A

  7. CHECK HARD DISK DRIVE


    1. Enter the "HDD Check" screen. Refer to Check Hard Disk Drive in Operation Check.

      Click here

      OK
      "OK" is displayed.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE HARD DISC DRIVE (HDD) Click here

    OK

  8. PROBLEM SYMPTOMS TABLE


    1. Refer to Problem Symptoms Table.

      Click here

      Result
      Result Proceed to
      Fault is not listed in Problem Symptoms Table A
      Fault is listed in Problem Symptoms Table B

      Tech Tips

      If the symptoms do not recur and no DTCs are output, attempt to reproduce the symptoms.


    B

    GO TO STEP 10 Click here

    A

  9. PERFORM TROUBLESHOOTING BASED ON PROBLEM SYMPTOM


    1. Terminals of ECU

      Click here

    2. Data List / Active Test

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  10. ADJUST, REPAIR OR REPLACE

    Result
    Proceed to
    NEXT

    NEXT

  11. RECHECK FOR DTC*


    1. After clearing DTCs, recheck for DTCs.

      Click here


      Body Electrical > Navigation System > Trouble Codes
      Result
      Proceed to
      NEXT

    NEXT

  12. PERFORM CONFIRMATION TEST

    Result
    Proceed to
    NEXT

    NEXT

    END