FRONT BRAKE FLEXIBLE HOSE INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The following procedure is for the LH side.

Note


  • Since the RH side flexible hose and LH side flexible hose are not interchangeable, verify the part numbers when installing the front flexible hoses.

  • If the front flexible hose are to be reused, connect them after checking the identifiction marks plced when each hose was disconnected.

PROCEDURE


  1. INSTALL FRONT FLEXIBLE HOSE


    1. Connect the front flexible hose to the disc brake cylinder assembly LH with a new gasket and new union bolt.

      Torque:
      30.4 N*m  { 310 kgf*cm, 22 ft.*lbf }

      Tech Tips

      Insert the flexible hose lock securely into the lock hole in the disc brake cylinder assembly LH.

    2. w/ AVS:


      1. A01XP5XC01
        *1 Front Flexible Hose Bracket
        *2 Front Speed Sensor Clamp

        Set the flexible hose clamp on the flexible hose bracket.

      2. Hook the hook labeled A of the front speed sensor bracket onto the part of the absorber bracket labeled C.

      3. Insert the hook labeled B of the front speed sensor bracket into the part of the absorder bracket labeled D.

      4. Install the front flexible hose and front speed sensor bracket to the absorber bracket with the bolt.

        Torque:
        18.8 N*m  { 192 kgf*cm, 14 ft.*lbf }
      5. A01XOYTN01

        Install the flexible hose bracket and speed sensor clamp to the steering knuckle with the bolt labeled D.

        Torque:
        18.8 N*m  { 192 kgf*cm, 14 ft.*lbf }

      6. Install a new clip to the front flexible hose.

        Note

        Insttall the clip as far as it will go.

      7. A01XNFOC01
        *a Torque Wrench Fulcrum Length

        Using a union nut wrench, connect the front flexible hose to the brake tube labeled A while holding the front flexible hose with a wrench.

        Torque:
        Specified tightening torque
        15.2 N*m  { 155 kgf*cm, 11 ft.*lbf }

        Tech Tips


        • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

          Click here

        • When using union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 13.4 N*m (137 kgf*cm, 10ft.*lbf)

        Note


        • Do not bend or damage the brake tube.

        • Do not allow any foreign matter such as dirt and dust to enter the brake tube from the connecting point.

    3. w/o AVS:


      1. A01XNYBC01
        *1 Absorber Bracket
        *2 Flexible Hose Bracket
        *3 Front Speed Sensor Bracket

        Set the flexible hose clamp on the flexible hose bracket.

      2. Hook the hook labeled A of the front speed sensor bracket onto the part of the absorber bracket labeled C.

      3. Insert the hook labeled B of the front speed sensor bracket into the part of the absorber bracket labeled D.

      4. A01XOLPN01

        Install the front flexible hose and front speed sensor bracket to the absorber bracket with the bolt.

        Torque:
        18.8 N*m  { 192 kgf*cm, 14 ft.*lbf }

      5. Install the front flexible hose to the steering knuckle with the bolt labeled D.

        Torque:
        18.8 N*m  { 192 kgf*cm, 14 ft.*lbf }

      6. Install a new clip to the front flexible hose.

        Note

        Install the clip as far as it will go.

      7. A01XNA3C01
        *a Torque Wrench Fulcrum Length

        Using a union nut wrench, connect the brake tube to the front flexible hose while holding the front flexible hose with a wrench.

        Torque:
        Specified tightening torque
        15.2 N*m  { 155 kgf*cm, 11 ft.*lbf }

        Tech Tips


        • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

          Click here

        • When using union nut wrench (fulcrum length of 22 mm (0. 8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 13.4 N*m (137 kgf*cm, 10ft.*lbf)

        Note


        • Do not bend or damage the brake tube.

        • Do not allow any foreign matter such as dirt and dust to enter the brake tube from the connecting parts.

  2. BLEED BRAKE LINE

    Click here

  3. INSTALL FRONT WHEEL

    Click here