FRONT SPEED SENSOR INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the LH side and RH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. INSTALL FRONT SKID CONTROL SENSOR WIRE LH (w/ AVS)


    1. Install the sensor clamp as follows.


      1. B0058YFC02
        *1 Absorber Bracket
        *2 Flexible Hose Clamp
        *3 Skid Control Sensor Clamp

        Install the grommet to the absorber bracket.

      2. Attach hook A of the sensor clamp to the absorber bracket.

        Note

        Do not twist the wire harness for the sensor clamp when installing it.

      3. Install the flexible hose clamp together with the skid control sensor clamp to the absorber bracket with the bolt.

        Torque:
        18.8 N*m  { 192 kgf*cm, 14 ft.*lbf }

      4. Install the grommet to the absorber bracket.

      5. Connect the connector to the absorber control actuator.

    2. Install the sensor clamp to the side member with the bolt.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note

      Do not twist the wire harness for the sensor clamp when installing it.

    3. Install the clamp.

    4. Fold back the fender liner and connect the connector.

  2. INSTALL FRONT SPEED SENSOR LH (w/ AVS)


    1. B0058WG

      Install the flexible hose clamp together with the sensor clamp with the bolt.

      Torque:
      18.8 N*m  { 192 kgf*cm, 14 ft.*lbf }

      Note

      Do not twist the wire harness for the sensor clamp when installing it.

    2. Install the front speed sensor LH to the steering knuckle with the bolt.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note


      • Prevent foreign matter from attaching to the front speed sensor tip.

      • Firmly insert the front speed sensor body into the steering knuckle before tightening the bolt.

    3. Connect the connector.

  3. INSTALL FRONT SPEED SENSOR LH (w/o AVS)


    1. Install the front speed sensor LH to the steering knuckle with the bolt.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note


      • Prevent foreign matter from attaching to the front speed sensor tip.

      • Firmly insert the front speed sensor body into the steering knuckle before tightening the bolt.

    2. Install the sensor clamp as follows.


      1. B00585RC01
        *1 Absorber Bracket
        *2 Flexible Hose Clamp

        Attach hook A and B of the sensor clamp to the flexible hose bracket.

        Note

        Do not twist the wire harness for the sensor clamp when installing it.

      2. Install the flexible hose clamp together with the sensor clamp to the absorber bracket with the bolt.

        Torque:
        18.8 N*m  { 192 kgf*cm, 14 ft.*lbf }

      3. Install the clamp to the absorber bracket.

    3. Install the sensor clamp to the side member with the bolt.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note

      Do not twist the wire harness for the sensor clamp when installing it.

    4. Install the clamp.

    5. Fold back the fender liner and connect the connector.

  4. INSTALL FRONT TIRE

    Click here

  5. CHECK FOR SPEED SENSOR SIGNAL

    Click here